Caterpillar cat 307 csb mini hydraulic excavator (prefix bcm) service repair manual (bcm00001 and up)

Service Repair Manual
Models
307C and 307CSB Mini
Hydraulic Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307C MINI HYD EXCAVATOR BCM
Configuration: 307C & 307C SB Excavators BCM00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307C Excavator Machine Systems
Media Number -RENR4029-02 Publication Date -01/03/2005 Date Updated -29/03/2005
i06217139
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT3209 Retainer Nut Wrench As. 1
Start By:
A. Remove final drive and travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/18307C & 307C SB Excavators BCM00001-UP (MACHINE) POWERED BY 4M40 En...
2020/1/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02992200
1. Remove relief valves (3) . Remove bolts (2) and remove motor cover (1) .
2. Remove backup ring (4) and O-ring seal (5) from relief valves (3) .

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove cover (6) . Repeat step on the opposite side of the motor cover.
4. Remove spring (9) , pusher (8) and spool (7) from behind cover (6) .

5. Remove plug (10) .
6. Remove spring (11) , spool (12) from under plug (10) .

7. Remove plugs (13) and (14) .
8. Remove O-ring seals (15) from plugs. Remove steel balls (16) from motor cover.

9. Remove plug (17) from motor cover.
10. Remove spring (18) and poppet (19) from behind plug (17) . Remove O-ring seal (20) from
plug (17) . Repeat step on opposite side of the motor cover.

11. Remove valve plate (21) .
12. Remove bearing (22) .
13. Position final drive assembly as shown and remove O-ring seals (23) , (24) , and (25) .

Note: Use caution when using forced air, propelled parts can cause injury.
14. Apply shop air to brake piston oil port and remove brake piston (26) from body casing.
15. Remove backup rings (27) and (30) . Remove O-ring seals (28) and (29) from brake piston
(26) .
16. Remove friction plates (31) and steel plates (32) .
Note: Do not remove cylinder barrel during this step.

17. Position final drive assembly as shown. Remove barrel assembly (33) .
Note: During reassembly, the retainer, piston assemblies, and cylinder barrel must be
installed in the original locations. For this purpose, record the original positions of the parts
before and during disassembling process.
18. Remove retainer (34) with piston assemblies (35) from cylinder barrel (33) . Remove the
piston assemblies (35) from the retainer (34) .

19. Remove retainer ball (36) from cylinder barrel (33) .
20. Remove three pins (37) from cylinder barrel (33) .
10/18307C & 307C SB Excavators BCM00001-UP (MACHINE) POWERED BY 4M40 ...

21. Use a suitable press to apply pressure to plate (38) and remove snap ring (41) . Release
pressure from plate (38) . Remove plate (38) , spring (40) and plate (39) from cylinder
barrel (33) .
22. Remove swash plate (42) .

23. Remove steel balls (43) , piston assembly (44) , and spring (45) .
24. Position gear casing as shown. Remove bolts (46) and washers (47) .

Plate shown from bottom with fill and drain plugs removed.
25. Use a plastic hammer to loosen the sealant bond. Separate the cover (48) and the gear casing
(49)
26. Remove bolts (50) and thrust plate (51) .

27. Remove sun gear (52) , three planetary gears (53) , and three bearings (54) .
28. Remove carrier (55) .
29. If necessary, remove the three inner wheels (56) from the carrier.

30. Remove sun gear (57) . Remove bolts (58) and thrust plate (59) .
31. Remove four planetary gears (60) , four bearings (61) , four bushings (62) and four plates
(63) .

32. Remove bolt (64) and washer (65) .
33. Use a magnet to remove the pin (66)
Note: If pin is difficult to remove with magnet, follow the procedure listed.
a. Cover the screw hole with a piece of adhesive tape or a magnetic plate.
b. Drill a 3 mm (0.125 inch) hole in the pin (66) .
c. Thread a small screw into the hole drilled in the pin. Use necessary force to remove
the pin by grabbing onto the screw and pulling upwards.
34. Using tooling (A) , remove the ring nut (67) from the body casing.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

35. Use a suitable lifting device in order to remove the gear casing (50) from the body casing.
36. Remove angular bearing (68) from the gear casing.

37. Position gear casing upside down. Remove floating seal (69) and angular bearing (70) from
the gear casing.
38. Remove floating seal (73) from the body casing (74) .Tap the body casing with a plastic
hammer to remove shaft (71) and bearing (72) from the body casing (74) .
39. If necessary, remove the bearing (72) from the shaft (71) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jan 24 23:35:33 UTC+0800 2020

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 307C MINI HYD EXCAVATOR BCM
Configuration: 307C & 307C SB Excavators BCM00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
307C Excavator Machine Systems
Media Number -RENR4029-02 Publication Date -01/03/2005 Date Updated -29/03/2005
i06217162
Final Drive and Travel Motor - Assemble
SMCS - 4050-016; 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
B - Loctite High Flex Film -
C FT3209 Retainer Nut Wrench As. 1
D FT3208 Retainer Nut Wrench 1
E 9S-7353 Torque Wrench 1
F 6V-2055 Grease 1

Caterpillar cat 307 csb mini hydraulic excavator (prefix bcm) service repair manual (bcm00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

More from fjskefkksemm

More from fjskefkksemm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 307 csb mini hydraulic excavator (prefix bcm) service repair manual (bcm00001 and up)