2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308D MINI HYD EXCAVATOR FYC
Configuration: 308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
308D CR Excavator Machine Systems
Media Number -RENR9741-01 Publication Date -01/03/2010 Date Updated -03/03/2010
i03001513
Support (Swing Boom) - Remove
SMCS - 7051-S4
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-4758 Retaining Ring Pliers As 1
B
289-0008 Puller Stud 1
1P-1842 Puller Adapter 1
6V-2072 Sleeve assembly 1
6V-3175 Double Acting Cylinder 1
3S-6224 Electric Hydraulic Pump Gp 1
Start By:
A. Remove the boom. Refer to Disassembly and Assembly, "Boom - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01521292
1. Position suitable cribbing under swing boom cylinder (1), as shown.
Illustration 2 g01521293
2. Remove bolt (4). Remove pin assembly (2), shim (5), and shims (3). Reposition swing
boom cylinder (1) to one side.
2/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01521310
3. Remove bolts (6) and bracket (8). Remove rubber spacer (7) .
Illustration 4 g01521311
4. Use Tooling (A) to remove retaining ring (9). Remove shim (10) .
Illustration 5 g01521312
3/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Remove bolts (12). Use two persons or a suitable device for lowering in order to remove pin
assembly (11). The weight of pin assembly (11) is approximately 35 kg (77 lb).
Illustration 6 g01521314
Illustration 7 g01521786
6. Attach a suitable lifting device to support assembly (13). The weight of support assembly
(13) is approximately 299 kg (660 lb).
7. Remove bolts (14). Use two persons to remove lower pin assembly (15). The weight of pin
assembly (15) is approximately 26 kg (58 lb).
4/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01521745
The location of the above graphic is the upper support.
8. Take note of the placement of thrust washer (16) for installation purposes. Thrust washer
(16) may be displaced during the removal of the support assembly.
Illustration 9 g01521746
The location of the above graphic is the lower support.
9. Take note of the placement of shims (17) for installation purposes. Shims (17) may be
displaced during the removal of the support assembly.
5/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01521747
10. Carefully route hoses (18) through support assembly (13) during the removal of support
assembly (13). Use the suitable lifting device to remove support assembly (13) .
Illustration 11 g01521748
11. Remove lip seal (19) (not shown).
12. Use Tooling (B) to remove upper bearing (20) .
13. Repeat Steps 11 and 12 for the lower bearing.
6/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01521750
14. Use Tooling (B) to remove bearing (21) from support assembly (13). Repeat for the
remaining three bearings in support assembly (13) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jan 17 23:59:14 UTC+0800 2020
7/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308D MINI HYD EXCAVATOR FYC
Configuration: 308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
308D CR Excavator Machine Systems
Media Number -RENR9741-01 Publication Date -01/03/2010 Date Updated -03/03/2010
i03002614
Support (Swing Boom) - Install
SMCS - 7051-S4
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-4758 Retaining Ring Pliers As 1
B
289-0008 Puller Stud 1
1P-1842 Puller Adapter 1
6V-2072 Sleeve assembly 1
6V-3175 Double Acting Cylinder 1
3S-6224 Electric Hydraulic Pump Gp 1
C 1P-0520 Driver Gp 1
D 5P-0960 Grease Cartridge 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01521750
1. Use Tooling (B) to install four bearings (21) in support assembly (13) .
Illustration 2 g01521748
2. Use Tooling (B) to install upper bearing (20) .
3. Use Tooling (C) to install lip seal (19) (not shown).
2/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 4. Repeat Steps 2 and 3 for the lower bearing.
Illustration 3 g01521747
5. Use a suitable lifting device to position support assembly (13). The weight of support
assembly (13) is approximately 299 kg (660 lb).
6. Carefully route hoses (18) through support assembly (13) while you position support
assembly (13) on the machine.
Illustration 4 g01521745
The location of the above graphic is the upper support.
Note: Apply Tooling (D) to both surfaces of thrust washer (16) before installation.
7. Install thrust washer (16) in the same position that was noted in the removal procedure.
3/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 5 g01521746
The location of the above graphic is the lower support.
8. Install shims (17) in the same position that was noted in the removal procedure. Install the
required amount of shims (17) in order to achieve a maximum lateral clearance of 1.0 mm
(0.04 inch).
Illustration 6 g01521786
9. Apply Tooling (D) to the surface of the bore for upper pin assembly (15) before installation.
10. Use two persons to install upper pin assembly (15). The weight of upper pin assembly (15)
is approximately 26 kg (58 lb).
11. Install bolts (14) .
4/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 7 g01521312
12. Apply Tooling (D) to the surface of the bore for lower pin assembly (11) before installation.
13. Use two persons or a suitable device for raising in order to install lower pin assembly (11).
The weight of lower pin assembly (11) is approximately 35 kg (77 lb).
14. Install bolts (12) .
15. Remove the suitable lifting device from support assembly (13) .
Illustration 8 g01521311
16. Install shim (10). Use Tooling (A) to install retaining ring (9).
5/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 9 g01521310
17. Install rubber spacer (7). Install bracket (8) and bolts (6) .
Illustration 10 g01521293
18. Apply Tooling (D) to both bores for pin assembly (2) before installation. Install shim (5).
Position swing boom cylinder (1). Install shims (3) and pin assembly (2). Adjust shims (3)
to a maximum clearance of 1.0 mm (0.04 inch). Install bolt (3) .
6/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 11 g01521292
19. Remove the suitable cribbing from swing boom cylinder (1) .
End By: Install the boom. Refer to Disassembly and Assembly, "Boom - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 18 00:00:11 UTC+0800 2020
7/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308D MINI HYD EXCAVATOR FYC
Configuration: 308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 Engine
Disassembly and Assembly
308D CR Excavator Machine Systems
Media Number -RENR9741-01 Publication Date -01/03/2010 Date Updated -03/03/2010
i02856676
Window Wiper Motor - Remove and Install
SMCS - 7305
Removal Procedure
Illustration 1 g01423016
1. Remove bolts (1) and (2).
1/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01423019
2. Remove bolts (3) and move monitor (4) to one side. Remove bolts (5 ) and remove panel
(6).
Illustration 3 g01423022
3. Remove nut (8) and remove wiper arm (7).
2/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 4 g01423026
Illustration 5 g01423027
4. Remove cap (9). Remove nut (10) and two washers (11).
Illustration 6 g01423032
5. Remove bolts (12).
3/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 7 g01423036
6. Disconnect harness assembly (15). Remove bolts (14). Remove wiper motor assembly (13).
Installation Procedure
Illustration 8 g01423036
1. Position wiper motor assembly (13). Install bolts (14). Connect harness assembly (15).
4/7308D Mini Hydraulic Excavator FYC00001-UP (MACHINE) POWERED BY 4M40 ...
2020/1/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...