Caterpillar cat 336 f l xe excavator (prefix dfy) service repair manual (dfy00001 and up)

Service Repair Manual
Models
336F L XE
336F LN XE Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L XE EXCAVATOR DFY
Configuration: 336F L XE & 336F LN XE Excavators DFY00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
C9.3 Engines for Caterpillar Built Machines
Media Number -UENR0130-06 Publication Date -01/08/2015 Date Updated -22/05/2017
i05296500
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate all components of the rocker arm shaft with clean engine oil.
Illustration 1 g01947678
2. Install exhaust rocker arm (3) and inlet rocker arm (4) on rocker shaft (1).
1/2
336F L XE & 336F LN XE Excavators DFY00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

3. Install plug (2) into rocker shaft (1). Install plug (2) to a depth of 1.25 ± 0.25 mm
(0.049 ± 0.010 inch).
End By:
a. Install the rocker arm and shaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:15:41 UTC+0800 2020
2/2
2020/6/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06019448
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the exhaust manifold.
B. Remove the fan drive mounting group.
C. Remove the fuel rail and the fuel manifold.
D. Remove the fuel filter base.
E. Remove the inlet manifold.
F. Remove the rocker arm and shaft.
G. Remove the unit injectors.
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
2020/6/18

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Remove tube assembly (1) .
2/4
2020/6/18

2. Remove bolts (4) .
3. Remove bolts (3) and remove bracket (2) .
Note: Examine bolts (5) for wear or for damage. Refer to Reuse And Salvage Guidelines,
SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines". Replace with
new bolts (5) , if necessary.
4. Remove bolts (5) and remove bolts (6) .
3/4
2020/6/18

5. Attach a suitable lifting device to cylinder head (7) . The weight of cylinder head (7) is
approximately 147 kg (325 lb). Remove cylinder head (7) .
Thu Jun 18 22:16:37 UTC+0800 2020
4/4
2020/6/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06019490
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/5
2020/6/18

1. Attach a suitable lifting device to cylinder head (7) . The weight of cylinder head (7) is
approximately 147 kg (325 lb). Position cylinder head (7) .
Note: Examine bolts (5) for wear or for damage. Refer to Reuse And Salvage Guidelines,
SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines". Replace with
new bolts (5) , if necessary.
2. Install bolts (5) and install bolts (6) .
2/5
2020/6/18

Bolt tightening sequence
Note: Lubricate the bolts with clean engine oil prior to assembly.
3. Tighten bolt (1) through bolt (26) in a numerical sequence.
Tighten the bolts to the following torque. ... 160 ± 15 N·m (118 ± 11 lb ft)
4. Tighten bolt (1) through bolt (26) again in a numerical sequence.
Tighten the bolts again to the following torque. ... 160 ± 15 N·m (118 ± 11 lb ft)
5. Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical
sequence.
Rotate the bolts in the clockwise direction. ... 90 degrees (1/4 turn)
6. Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
Tighten the bolts to the following torque. ... 160 ± 15 N·m (118 ± 11 lb ft)
8. Tighten bolt (1) through bolt (26) again in a numerical sequence.
Tighten the bolts again to the following torque. ... 160 ± 15 N·m (118 ± 11 lb ft)
9. Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical
sequence.
Rotate the bolts in the clockwise direction. ... 90 degrees (1/4 turn)
3/5
2020/6/18

Tighten the bolts to the following torque. ... 28 ± 7 N·m ( 21 ± 5 lb ft)
11. Position bracket (2) and install bolts (3) .
12. Install bolts (4) .
13. Install tube assembly (1) .
4/5
2020/6/18

End By:
a. Install the unit injectors.
b. Install the rocker arm and shaft.
c. Install the inlet manifold.
d. Install the fuel filter base.
e. Install the fuel rail and the fuel manifold.
f. Install the fan drive mounting group.
g. Install the exhaust manifold.
Thu Jun 18 22:17:33 UTC+0800 2020
5/5
2020/6/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05296509
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 1
Start By:
a. Remove the cylinder head.
NOTICE
1/3
2020/6/18

1. Use Tooling (A) to remove valve lifters (1). Place identification marks on the valve lifters
for installation purposes.
Table 2
Required Tools
A FT-2730 Hook 1
B 8T-2998 Lubricant 1
2/3
2020/6/18

1. Apply Tooling (B) to valve lifters (1) prior to installation. Use Tooling (A) to install valve
lifters (1) in the original location in the cylinder block.
End By:
a. Install the cylinder head.
Thu Jun 18 22:18:29 UTC+0800 2020
3/3
2020/6/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05283832
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Table 1
Required Tools
A FT-2730 Hook 12
B 8T-2998 Lubricant -
Start By:
a. Remove the rocker arm and the shaft.
b. Remove the front cover.
NOTICE
1. Use Tooling (A) to reposition the valve lifters out of the way of the camshaft.
2. Set the No. 1 piston to top center on the compression stroke. Refer to Testing and Adjusting,
"Finding Top Center Position for No. 1 Piston".
1/5
2020/6/18

3. Ensure that the timing marks on camshaft gear (1) and idler gear (2) are aligned.
4. Remove bolts (3) and thrust plate (4) from the cylinder block.
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
5. Remove camshaft (5) from the cylinder block.
2/5
2020/6/18

Note: During the installation of the camshaft, rotate the camshaft in both directions in order to
prevent binding in the camshaft bearing bores.
1. Lubricate the camshaft lobes and the valve lifter bore with a 50/50 mixture of Tooling (B). Apply
clean engine oil on the camshaft bearing journals. Carefully install camshaft (5) in the cylinder
block.
3/5
2020/6/18

(6) Gear for the high-pressure fuel pump
(7) Camshaft gear
(8) Idler gear
(9) Crankshaft gear
(10) Timing marks
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2. Correct fuel injection timing and correct valve mechanism operation is determined by properly
timing crankshaft gear (9) and camshaft gear (7) to idler gear (8). Also, high-pressure fuel pump gear
(6) must be timed to camshaft gear (7). When installing the front gears, timing marks (10) on idler
gear (8) must be in alignment with the timing marks on crankshaft gear (9) and the timing marks on
camshaft gear (7). The "0" mark on camshaft gear (7) must align with the timing mark on idler gear
(8). The "V" mark on camshaft gear (7) must align with the "V" mark on fuel pump gear (6).
3. Install thrust plate (4) and bolts (3).
4. The maximum permissible end play for a worn camshaft is 0.46 mm (0.018 inch). The maximum
permissible end play for a new camshaft is 0.13 ± 0.08 mm (0.005 ± 0.003 inch).
5. Use Tooling (A) to position the valve lifters in the cylinder block.
6. Calibrate the speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor -
Calibrate".
End By:
a. Install the front cover.
4/5
2020/6/18

b. Install the rocker arm and the shaft.
Thu Jun 18 22:19:24 UTC+0800 2020
5/5
2020/6/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05296513
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft.
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
NOTICE
1/2
2020/6/18

Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Use a suitable press to remove the camshaft from camshaft gear (1).
Note: The temperature of the camshaft gear must not exceed 177 °C (350 °F) during
installation.
1. Raise the temperature of the camshaft gear up to a temperature of 177 °C (350 °F).
2. Align the key in the camshaft with the groove (keyway) in the camshaft gear.
3. Install the camshaft gear on the end of the camshaft.
End By:
a. Install the camshaft.
Thu Jun 18 22:20:20 UTC+0800 2020
2/2
2020/6/18

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05296537
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft.
NOTICE
1/5
2020/6/18

Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
1. Use Tooling (A) to remove camshaft bearings (1).
Table 2
Required Tools
A 8S-2241 Camshaft Bearing Tool Group 1
NOTICE
2/5
2020/6/18

1. Refer to Illustration 2 for the locations of the bearings.
(1a) Installation Dimension (A) for bearing (1a) ... 816.5 ± 0.8 mm (32.15 ± 0.03 inch)
(1b) Installation Dimension (B) for bearing (1b) ... 536.5 ± 0.8 mm (21.12 ± 0.03 inch)
(1c) Installation Dimension (C) for bearing (1c) ... 294.5 ± 0.8 mm (11.59 ± 0.03 inch)
(1d) Installation Dimension (D) for bearing (1d) ... 0.50 ± 0.25 mm (0.020 ± 0.010 inch)
3/5
2020/6/18

2. Use Tooling (A) to install all of camshaft bearings (1) except for the front bearing. Locate
oil hole (2) in each bearing so that oil hole (2) is located at the top of the bore. Locate joint
(3) in the proper position.
3. Use Tooling (A) to install the front camshaft bearing. Align oil hole (2) in the front
camshaft bearing with the oil hole in the cylinder block. Locate joint (3) in the front
camshaft bearing in the proper position (facing the cylinder block). Refer to Specifications,
"Cylinder Block" for more information.
End By:
a. Install the camshaft.
4/5
2020/6/18

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05296545
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
1. Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual for the correct procedure.
2. Remove bolts (1) and (3).
3. Loosen fitting (4) and remove oil gauge (2).
1/5
2020/6/18

4. Remove nuts (5). Remove switch assembly (6). Remove sound suppression cover (7).
Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to
tap lightly on the engine oil pan, if necessary.
5. Remove bolts (8). Remove studs (9). Remove engine oil pan (10) and the gasket.
Table 1
Required Tools
A − Loctite 587 −
2/5
2020/6/18

Caterpillar cat 336 f l xe excavator (prefix dfy) service repair manual (dfy00001 and up)

Recommended

Recommended

More Related Content

More from fjkskedmme

More from fjkskedmme (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 336 f l xe excavator (prefix dfy) service repair manual (dfy00001 and up)