The document provides instructions for disassembling and assembling a torque converter. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The instructions cover removing components like the cover, impeller and carrier assembly, stator, springs and rollers. Reassembly involves lowering component temperatures and installing components like bearings, gears, seals and rings in the reverse order of removal. Tightening torques are specified for some bolts.
Caterpillar cat 120 m motor grader (prefix r9c) service repair manual (r9c000...fjsjjekdkme
This document provides disassembly instructions for the transmission of a 120M motor grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission housing, clutch assemblies, seals, sensors and gears. Detailed notes are provided on tooling required and part orientations to aid reassembly. Safety precautions are highlighted, and fluids and contaminants are to be handled per regulations.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 938 g ii wheel loader (prefix crd) service repair manual (crd...fjsjjekdkme
This document provides disassembly instructions for the transmission of a 938G II Wheel Loader. It lists the required tools and provides step-by-step instructions to disassemble the various components of the transmission, including removing gears, hubs, seals, plates, and other parts. Detailed illustrations accompany each step to show how to position the components and which tools to use for removal. Proper cleaning and inspection of parts is advised during disassembly.
Caterpillar cat 140 k 2 motor grader (prefix szw) service repair manual (szw0...fusjefjskekmem
This document provides instructions for disassembling and assembling the final drive components of a 140K 2 Motor Grader. The disassembly process involves removing 24 separate components from the final drive housing. The assembly section outlines assembling the components in the reverse order and includes checking clearances with tools. Proper lubrication and heating of bearings is required during assembly.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 120 m series 2 motor grader (prefix r9n) service repair manua...fjsjjekdkme
This document provides instructions for disassembling the transmission of a 120M Series 2 Motor Grader. It lists over 40 individual steps and provides illustrations for each step. The transmission must be removed from the grader and various components disassembled, including housing components, gears, seals, plates, and sensors. Special tools are required and spring forces must be released safely. The process involves removing over 50 individual parts in a specific sequence.
Caterpillar cat 120 m motor grader (prefix r9c) service repair manual (r9c000...fjsjjekdkme
This document provides disassembly instructions for the transmission of a 120M motor grader. It lists over 40 steps and accompanying illustrations to remove components like the transmission housing, clutch assemblies, seals, sensors and gears. Detailed notes are provided on tooling required and part orientations to aid reassembly. Safety precautions are highlighted, and fluids and contaminants are to be handled per regulations.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 938 g ii wheel loader (prefix crd) service repair manual (crd...fjsjjekdkme
This document provides disassembly instructions for the transmission of a 938G II Wheel Loader. It lists the required tools and provides step-by-step instructions to disassemble the various components of the transmission, including removing gears, hubs, seals, plates, and other parts. Detailed illustrations accompany each step to show how to position the components and which tools to use for removal. Proper cleaning and inspection of parts is advised during disassembly.
Caterpillar cat 140 k 2 motor grader (prefix szw) service repair manual (szw0...fusjefjskekmem
This document provides instructions for disassembling and assembling the final drive components of a 140K 2 Motor Grader. The disassembly process involves removing 24 separate components from the final drive housing. The assembly section outlines assembling the components in the reverse order and includes checking clearances with tools. Proper lubrication and heating of bearings is required during assembly.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 120 m series 2 motor grader (prefix r9n) service repair manua...fjsjjekdkme
This document provides instructions for disassembling the transmission of a 120M Series 2 Motor Grader. It lists over 40 individual steps and provides illustrations for each step. The transmission must be removed from the grader and various components disassembled, including housing components, gears, seals, plates, and sensors. Special tools are required and spring forces must be released safely. The process involves removing over 50 individual parts in a specific sequence.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 330 f excavator (prefix jfr) service repair manual (jfr00001 ...fjskekdmjekm
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure instructs putting the final drive back together in reverse order and adjusting the bearing preload using shims to achieve the proper clearance. Precise tools and torque specifications are required to correctly reassemble the 550 kg final drive transmission.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing new seals and determining the correct shim thickness between bearings and gears. Proper cleaning, application of sealants, and torque specifications are emphasized to correctly reassemble the final drive.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 f excavator (prefix lcg) service repair manual (lcg00001 ...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual components of the final drive including gears, shafts, housings, seals and bearings. The assembly section similarly lists over 30 steps to reinstall these components in reverse order, noting the required tools and specifying torques, seals and adhesives to use during reassembly. Precise measurements are taken to properly set the bearing preload using shims.
Caterpillar cat 349 e l vg excavator (prefix dge) service repair manual (dge0...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 349E L-VG excavator. It describes 33 steps to disassemble the final drive components including removing bolts, gears, shafts, and housings. It also lists the required tools and specifications for reassembly, describing 14 steps such as applying anti-seize compound, installing seals, gears, and housings using lifting devices and installation tools. The document contains diagrams illustrating each step.
Caterpillar cat 324 d l excavator (prefix pyt) service repair manual (pyt0000...jfksekmmdme
This document provides instructions for assembling the final drive of a 324D L excavator. It outlines 30 steps, including installing bearings and seals, determining the correct shim thickness, and joining the main housing to the motor housing. Cleanliness is emphasized throughout the assembly process to prevent contamination. Various tools are required, and components should be lubricated before assembly.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...jiaoyi82414369
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes how to remove components such as the axle shaft, planetary carrier assembly, bearing nut and seals. It also explains how to install these components in reverse order, noting important steps like properly installing duo-cone seals and ensuring components are clean and lubricated. The document contains diagrams to illustrate the procedures.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...yinranhe0814
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II Wheel Loader. It describes how to remove components such as the axle housing assembly, planetary carrier assembly, axle shaft, bearing nut, and seals. Detailed steps and illustrations are provided to guide removal and installation of these parts, including the use of various tools. Proper cleaning and lubrication of components during reassembly is emphasized.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...aags15120808
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes how to remove components such as the axle shaft, planetary carrier assembly, retaining rings, and seals. Detailed steps are provided for disassembling the planetary carrier assembly. The assembly procedure describes how to install components in reverse order and includes notes about properly installing duo-cone seals. Tools required are listed.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to completely disassemble the travel motor, removing components like the head, brake piston, plates, seals, bearings, and housing pieces. Various tools are required including an adapter, bolts, retaining ring pliers, and a bearing puller group. Safety notices are included to warn of potential spring forces or fluid hazards during disassembly.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step for clarity.
Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm4000...fjjskdmnenemm
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step for clarity.
1) The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and identifying parts to ensure proper reinstallation.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play.
4) Instructions for installing the fully reassembled pump drive back onto the engine.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include safety notices and illustrations. Removal involves disconnecting hoses, removing retaining components, and extracting parts from the cylinder head or engine. Installation is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document includes illustrations to identify the specific components and tools required for each procedure.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 330 f excavator (prefix jfr) service repair manual (jfr00001 ...fjskekdmjekm
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure instructs putting the final drive back together in reverse order and adjusting the bearing preload using shims to achieve the proper clearance. Precise tools and torque specifications are required to correctly reassemble the 550 kg final drive transmission.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 374 f l excavator (prefix dnm) service repair manual (dnm0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. The disassembly process involves removing over 30 individual parts from the final drive housing using various tools. The assembly process reverses the disassembly steps and provides details on installing new seals and determining the correct shim thickness between bearings and gears. Proper cleaning, application of sealants, and torque specifications are emphasized to correctly reassemble the final drive.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 f excavator (prefix lcg) service repair manual (lcg00001 ...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly process involves using various tools to remove over 30 individual components of the final drive including gears, shafts, housings, seals and bearings. The assembly section similarly lists over 30 steps to reinstall these components in reverse order, noting the required tools and specifying torques, seals and adhesives to use during reassembly. Precise measurements are taken to properly set the bearing preload using shims.
Caterpillar cat 349 e l vg excavator (prefix dge) service repair manual (dge0...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 349E L-VG excavator. It describes 33 steps to disassemble the final drive components including removing bolts, gears, shafts, and housings. It also lists the required tools and specifications for reassembly, describing 14 steps such as applying anti-seize compound, installing seals, gears, and housings using lifting devices and installation tools. The document contains diagrams illustrating each step.
Caterpillar cat 324 d l excavator (prefix pyt) service repair manual (pyt0000...jfksekmmdme
This document provides instructions for assembling the final drive of a 324D L excavator. It outlines 30 steps, including installing bearings and seals, determining the correct shim thickness, and joining the main housing to the motor housing. Cleanliness is emphasized throughout the assembly process to prevent contamination. Various tools are required, and components should be lubricated before assembly.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...jiaoyi82414369
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes how to remove components such as the axle shaft, planetary carrier assembly, bearing nut and seals. It also explains how to install these components in reverse order, noting important steps like properly installing duo-cone seals and ensuring components are clean and lubricated. The document contains diagrams to illustrate the procedures.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...yinranhe0814
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II Wheel Loader. It describes how to remove components such as the axle housing assembly, planetary carrier assembly, axle shaft, bearing nut, and seals. Detailed steps and illustrations are provided to guide removal and installation of these parts, including the use of various tools. Proper cleaning and lubrication of components during reassembly is emphasized.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...aags15120808
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes how to remove components such as the axle shaft, planetary carrier assembly, retaining rings, and seals. Detailed steps are provided for disassembling the planetary carrier assembly. The assembly procedure describes how to install components in reverse order and includes notes about properly installing duo-cone seals. Tools required are listed.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to completely disassemble the travel motor, removing components like the head, brake piston, plates, seals, bearings, and housing pieces. Various tools are required including an adapter, bolts, retaining ring pliers, and a bearing puller group. Safety notices are included to warn of potential spring forces or fluid hazards during disassembly.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step for clarity.
Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm4000...fjjskdmnenemm
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step for clarity.
Similar to Caterpillar cat 938 g series ii wheel loader (prefix b9y) service repair manual (b9y00001 and up) (7)
1) The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and identifying parts to ensure proper reinstallation.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play.
4) Instructions for installing the fully reassembled pump drive back onto the engine.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include safety notices and illustrations. Removal involves disconnecting hoses, removing retaining components, and extracting parts from the cylinder head or engine. Installation is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document includes illustrations to identify the specific components and tools required for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...fjjskmdmem
The document provides instructions for removing and installing wheel spindle assemblies on a Caterpillar 966C wheel loader. Key steps include removing the brake shoes, brake camshaft, and air lines before removing the spindle assembly using a hoist. Installation involves installing seals and bearings on the spider and bearing assembly before placing it on the spindle and securing with nuts. Brake components and air lines are then reinstalled.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...fjjskmdmem
This document provides instructions for removing and installing various components of the 966C wheel loader's power train, including wheels, brake shoes, wheel spindles, the front differential and carrier, and the rear differential and carrier. The procedures involve draining fluids, removing bolts and seals, using hoists and jacks, and reinstalling components in the reverse order while applying lubricants and torques as specified. Safety precautions are noted such as relieving air pressure from brake systems before disconnecting lines.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...fjjskmdmem
The document provides instructions for removing and installing various components of the rear differential and carrier assembly of a 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gears that allow the rear wheels to turn at different speeds.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j063...fjjskmdmem
This document provides instructions for removing and installing various components of the power train on a 966C wheel loader, including axles, final drive planet carriers, final drive ring gears and hubs, and wheels/bearings. The procedures describe draining oil, removing retaining rings and gears, and reinstalling components along with adjusting wheel bearings and installing seals.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...fjjskmdmem
This document provides instructions for removing and installing various components of the final drive and wheel assembly of a 966C wheel loader, including:
- Removing and installing final drive planet carriers
- Disassembling and assembling final drive planet carriers
- Removing and installing final drive ring gears, hubs, and wheels
- Removing and installing wheels, bearings, and seals
- Removing and installing brake shoes
The document contains detailed step-by-step instructions and diagrams for each procedure.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjjskmdmem
The document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 966C wheel loader. It describes:
1) Removing components like the fuel rack, lifters, camshaft, and bearings during disassembly.
2) Cleaning and lubricating parts before assembly.
3) Installing bearings, camshaft, lifters, fuel rack, and other components in reverse order of removal.
4) Timing the fuel injection pump housing and governor during installation on the engine.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b002...fjjskmdmem
1. The documents provide instructions for removing, installing, and servicing components of the engine oil filter base and cylinder head valves for a Caterpillar 966C wheel loader.
2. The procedures include using various tools to remove and install valves, valve guides, valve seat inserts, and the engine oil filter base.
3. Precautions are provided such as keeping parts clean and containing fluids during repair work.
Caterpillar cat 950 e wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include lists of required tools and parts, diagrams illustrating the component locations and removal/installation steps, and torque specifications for reinstalling components. Safety precautions are noted, such as blocking wheels and releasing parking brakes before removing drive shafts.
Caterpillar cat 950 e wheel loader (prefix 63r) service repair manual (63r060...fjjskmdmem
This document provides instructions for disassembling and assembling the transfer gears of a Caterpillar 950B wheel loader. It describes removing and installing over 30 individual parts in 14 steps. Key steps include using bolts and screws to separate the transmission from the transfer gears, removing bearing cages and gears, and checking bearing end play during reassembly. Proper heating and cooling of parts is emphasized during assembly/disassembly. The document also provides brief instructions for connecting and disconnecting the steering frame lock link and removing and installing the loader bucket.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z031...fjjskmdmem
This document provides instructions for removing and installing a crankshaft on a Caterpillar 3304B or 3306B engine. It describes using various tools to remove the crankshaft by lifting it straight up after removing connecting rods, caps and bolts. It also details installing new main and connecting rod bearings, checking clearances with plastigage, and reinstalling the crankshaft by lowering it into place and reattaching connecting rods and caps. A second section provides steps for accurately checking bearing clearances using plastic gauge strips.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z000...fjjskmdmem
1. The document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines, including the fuel injection pump housing, governor, and related parts.
2. The procedures include removing and installing bearings, camshafts, lifters, racks, gaskets and covers using various tools. Proper positioning and torque specifications are provided.
3. Detailed illustrations accompany each step to show how to disassemble and assemble the parts in the correct order and orientation.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include numbered steps detailing how to properly support and secure the components, which fasteners to remove and install, and proper torques to use.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r028...fjjskmdmem
The document provides instructions for removing and installing an exhaust manifold on a Caterpillar 950B wheel loader. Key steps include removing the turbocharger, fuel injection lines, exhaust manifold nuts and bolts, and exhaust manifold gaskets. When installing, apply anti-seize compound to studs if removed previously and ensure the two longer studs are in the correct position. Proper cleaning and installation of all parts is emphasized to prevent contamination.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r000...fjjskmdmem
This document provides instructions for removing and installing various components of a Caterpillar 3304 engine, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures provide detailed steps and illustrations for each component, with notices to keep parts clean and properly align timing marks.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G II WHEEL LOADER B9Y
Configuration: 938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power
Train
Media Number -RENR6068-03 Publication Date -01/12/2008 Date Updated -19/12/2008
i01886319
Torque Converter - Disassemble - Fixed
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 154-6181 Forcing Screw 2
C 2P-8312 Retaining Ring Pliers 1
D 1P-0520 Driver Gp 1
Start By:
A. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter - Separate".
1/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00978219
1. Install Tooling (A) and a suitable lifting device onto cover (2). The weight of cover (2) is
approximately 159 kg (350 lb). Remove bolts (1) and remove cover (2) .
Illustration 2 g00978237
2. Attach Tooling (A) and a suitable lifting device onto the torque converter assembly. The
weight of the torque converter assembly is approximately 75 kg (165 lb). Place torque
converter assembly on a bench and remove bolts (3) .
2/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00978253
3. Install Tooling (B) and remove the impeller and carrier assembly (4). The weight of
impeller and carrier assembly (4) is approximately 36 kg (80 lb).
Illustration 4 g00978993
4. Use Tooling (C) and remove retaining ring (6). Remove retaining ring (5) and stator (7) .
Illustration 5 g00978994
3/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 5. If necessary, use a suitable press and Tooling (D) in order to remove adapter (8) from stator
(7) .
Illustration 6 g00978996
6. Use Tooling (C) in order to remove retaining ring (11) from carrier assembly (12). Remove
spacer (10) .
Illustration 7 g00978998
7. Use a soft faced hammer in order to remove carrier assembly (12) from impeller (9) .
4/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g00979011
8. Remove retaining ring (13) from carrier assembly (12) .
Illustration 9 g00979012
9. Remove bolts (14) and remove gear (15) from impeller (16) .
Illustration 10 g00979015
10. Use a suitable press and Tooling (D) in order to remove bearing (17) from impeller (16) .
5/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 11 g00979023
11. Remove retaining ring (18) and cover (19) .
Illustration 12 g00979026
12. Remove O-ring seal (20). Use Tooling (C) and remove retaining ring (21) .
6/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 13 g00979029
13. Remove spacer (22) .
Illustration 14 g00979030
14. Use a suitable press and Tooling (D) in order to remove bearing (24) from housing (23) .
Illustration 15 g00979033
15. Remove bolts (25) and hub assembly (26) from turbine (27) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 1 18:20:55 UTC+0800 2020
7/7
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G II WHEEL LOADER B9Y
Configuration: 938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power
Train
Media Number -RENR6068-03 Publication Date -01/12/2008 Date Updated -19/12/2008
i01885710
Torque Converter - Disassemble - Free Wheel
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 154-6181 Forcing Screw 2
C 2P-8312 Retaining Ring Pliers 1
D 1P-0520 Driver Gp 1
Start By:
A. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter - Separate".
1/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 1 g00978219
1. Install Tooling (A) and a suitable lifting device onto cover (2). The weight of cover (2) is
approximately 159 kg (350 lb). Remove bolts (1) and remove cover (2) .
Illustration 2 g00978237
2. Attach Tooling (A) and a suitable lifting device onto the torque converter assembly. The
weight of the torque converter assembly is approximately 75 kg (165 lb). Place torque
converter assembly on a bench and remove bolts (3) .
2/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 3 g00978253
3. Install Tooling (B) and remove the impeller and carrier assembly (4). The weight of
impeller and carrier assembly (4) is approximately 36 kg (80 lb).
Illustration 4 g00978315
4. Use Tooling (C) in order to remove retaining ring (5). Remove stator (14) .
Illustration 5 g00978321
3/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 5. Remove retaining ring (6) and plate (7) .
Illustration 6 g00978328
6. Remove washer (8) .
Illustration 7 g00978338
7. Remove race (9) .
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 8 g00978386
8. Remove springs (10) and rollers (11) .
Illustration 9 g00978401
9. Remove retaining ring (12) and washer (13) .
5/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 10 g00978407
Illustration 11 g00978755
10. If necessary, raise the temperature of stator (14) and cam (15). Use a suitable press and
Tooling (D) in order to remove cam (15) .
Illustration 12 g00978759
11. Remove spacer (16) .
6/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 13 g00978760
12. Use a soft faced hammer in order to remove carrier assembly (17) from impeller (18) .
Illustration 14 g00978763
13. Remove retaining ring (19) from carrier assembly (17) .
Illustration 15 g00978766
14. Remove bolts (20). Remove gear (21) from impeller (18) .
7/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 16 g00978776
15. Use a suitable press and Tooling (D) in order to remove bearing (22) .
Illustration 17 g00978779
16. Remove retaining ring (23) and cover (24) .
Illustration 18 g00978780
17. Use Tooling (C) and remove retaining ring (25). Remove O-ring seal (26) .
8/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 19 g00978792
18. Remove spacer (27) .
Illustration 20 g00978794
19. Use a suitable press and Tooling (D) in order to remove bearing (28) from housing (29) .
9/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 21 g00978797
20. Remove bolts (30). Remove hub (31) from turbine (32) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 1 18:21:52 UTC+0800 2020
10/10
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY ...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G II WHEEL LOADER B9Y
Configuration: 938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power
Train
Media Number -RENR6068-03 Publication Date -01/12/2008 Date Updated -19/12/2008
i01885788
Torque Converter - Assemble - Free Wheel
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
C 2P-8312 Retaining Ring Pliers 1
Illustration 1 g00978839
1. Lower the temperature of bearing (28) and install bearing (28) into housing (29) .
1/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 2 g00978842
2. Install bolts (30). Tighten bolts (30) to a torque of 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00978837
3. Lower the temperature of hub assembly (31) and install hub (31) into housing (29) .
Illustration 4 g00983541
2/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
4. Install a new O-ring seal (26). Install spacer (27). Use Tooling (C) and install retaining ring
(25) .
Illustration 5 g00978779
5. Position cover (24) and install retaining ring (23) .
Illustration 6 g00978885
6. Lower the temperature of bearing (22) and install bearing (22) .
3/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 7 g00978766
7. Install gear (21) onto impeller (18). Install bolts (20). Tighten bolts (20) to a torque of 105 ±
15 N·m (77 ± 11 lb ft).
Illustration 8 g00978763
8. Install retaining ring (19) onto carrier assembly (17) .
Illustration 9 g00978886
4/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 9. Use a soft faced hammer and install carrier assembly (17) .
Illustration 10 g00978759
10. Install spacer (16) .
Illustration 11 g00978905
11. Install race (9) .
5/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 12 g00978906
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
12. Install rollers (11) and springs (10). Install springs (10) with the maximum number of loops
toward the outside diameter of the cam.
Illustration 13 g00978908
13. Install washer (13) and retaining ring (12) .
Illustration 14 g00978328
6/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 14. Install washer (8) .
Illustration 15 g00978321
15. Install plate (7) and install retaining ring (6) .
Illustration 16 g00983544
16. Install stator (14) onto carrier assembly (17). Use Tooling (C) and install retaining ring (5) .
7/8
938G SERIES II WHEEL LOADER B9Y00001-UP (MACHINE) POWERED BY 31...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...