Caterpillar cat 160 m series 3 motor grader (prefix n9e) service repair manual (n9e00001 and up)

Service Repair Manual
Models
160M Series 3 Motor Grader

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 160M 3 MOTOR GRADER N9E
Configuration: 160M Series 3 Motor Grader N9E00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems
Media Number -UENR3488-02 Publication Date -01/09/2018 Date Updated -24/09/2018
i05818258
Piston Pump (Hydraulic and Steering) - Remove
SMCS - 4306-011; 5070-011
Removal Procedure
Start By:
a. Remove the piston pump (hydraulic fan). Refer to Disassembly and Assembly, "Piston
Pump (Hydraulic Fan) - Remove".
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3160M Series 3 Motor Grader N9E00001-UP (MACHINE) POWERED BY C9.3 Engin...
2019/12/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03683148
1. Disconnect harness assembly (1). Disconnect hose assemblies (2) and (3).
2. Disconnect hose assemblies (4) and (5). Reposition bracket assembly (6).

3. Attach a suitable lifting device to piston pump (7). The weight of piston pump (7) is
approximately 52 kg (115 lb).
4. Remove bolts (8) in order to remove piston pump (7) from the machine.
5. Remove O-ring seal (9) from piston pump (7).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Dec 24 09:12:23 UTC+0800 2019

Shutdown SIS
Previous Screen
i02649334
Piston Pump (Hydraulic and Steering) - Disassemble
SMCS - 4306-015; 5070-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 1P-1857 Retaining Ring Pliers 1
C 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic
and Steering) - Remove".

1. Remove bolts (1) and valve (2).
2. Remove O-ring seals (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (9), the O-ring seal, retainer (8), spring (7), retainer (6), spool (5), plug (4),
and the O-ring seal.

4. Remove plug (16), the O-ring seal, retainer (15), spring (14), rod (13), retainer (12), spool
(11), plug (10), and the O-ring seal.
5. Remove bolts (17) and head (18).
6. Remove piston (22), piston (21), spring (24), gasket (19), port plate (20), and bearing cup
(23).

7. Remove bearing cone (25).
8. Remove shim (26), barrel (27), and dowel (28).

9. Use Tooling (A), Tooling (B), and a suitable press in order to remove retaining ring (32)
from barrel (27).
10. Remove washer (31), spring (30), and washer (29).
11. Remove bolts (33) and cover (34).

12. Remove O-ring seal (35).
13. Remove plug (36).
14. Remove shaft (37), bolts (39), and plates (38).

15. Remove plates (40), retainer (41), and pistons (42).
16. Remove swashplate (43).
17. Remove screws (45), bearings (44), bearing cone (46), and bearing cup (47).

18. Remove lip seal (50).
19. Use Tooling (C) in order to remove retaining ring (49).
20. Remove lip seal (48).
Tue Dec 24 09:13:19 UTC+0800 2019

Shutdown SIS
Previous Screen
i02649335
Piston Pump (Hydraulic and Steering) - Assemble
SMCS - 4306-016; 5070-016
Assembly Procedure
1. Install lip seal (48).
2. Use Tooling (C) in order to install retaining ring (49).
3. Install lip seal (50).

4. Install screws (45), bearings (44), bearing cone (46), and bearing cup (47).
5. Install swashplate (43).
6. Install shaft (37).
7. Install plug (36).
8. Install dowel (28).

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
9. Install washer (31), spring (30), and washer (29).
10. Use Tooling (A), Tooling (B) and a suitable press in order to install retaining ring (32) onto
barrel (27).
11. Install pistons (42) into retainer (41) and barrel (27).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

12. Install barrel (27).
13. Install shim (26) and bearing cone (25).

14. Position plates (40) and plates (38).
15. Install bolts (39).
16. Install piston (22), piston (21), spring (24), gasket (19), port plate (20), and bearing cup
(23).

injury.
17. Install bolts (17) and head (18).
injury.
18. Install retainer (15), spring (14), rod (13), retainer (12), spool (11), plug (10), and the O-ring
seal. Install plug (16) and the O-ring seal.
19. Install retainer (8), spring (7), retainer (6), spool (5), plug (4), and the O-ring seal. Install
plug (9) and the O-ring seal.

20. Install O-ring seals (3).
21. Install bolts (1) and valve (2).
End By:
a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic and
Steering) - Install".
Tue Dec 24 09:14:14 UTC+0800 2019

Caterpillar cat 160 m series 3 motor grader (prefix n9e) service repair manual (n9e00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (6)

Similar to Caterpillar cat 160 m series 3 motor grader (prefix n9e) service repair manual (n9e00001 and up)

Similar to Caterpillar cat 160 m series 3 motor grader (prefix n9e) service repair manual (n9e00001 and up) (16)

More from fjjskefkksem

More from fjjskefkksem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 160 m series 3 motor grader (prefix n9e) service repair manual (n9e00001 and up)