This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Special tools are listed where required. Safety and contamination prevention practices are noted.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjkskedmme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr0...uuudfjjfjkkskm
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The instructions include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing nozzles and pumps following specific tightening procedures and torque specifications. Safety notices are also provided to keep parts clean and contain fluids properly during the repair process.
The document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing the fuel transfer pump from a Caterpillar 3306 engine. The procedures include:
- Turning off the fuel supply and disconnecting tubes and hoses
- Removing bolts and washers securing components and lifting parts off
- Checking condition of gaskets and installing new ones if needed
- Reinstalling components by securing with bolts and reconnecting tubes and hoses
The instructions emphasize cleaning parts and containing fluids during disassembly and reinstallation.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 322 c fm excavator (prefix c3r) service repair manual (c3r000...jfjskeksemmme
This document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR with a 3126B engine. The removal process involves disconnecting hoses and lines, removing bolts, and taking off the pump. Installation is the reverse of removal, and includes reconnecting hoses, bolts, and ensuring a tight seal. Proper cleaning and inspection of parts is emphasized. A separate section provides multi-step instructions for disassembling and assembling a turbocharger from the same excavator model.
Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 ...fjkskedmme
This document provides instructions for removing and installing components on a 345C Excavator, including:
- Removing and installing the fuel transfer pump
- Removing and installing the electronic unit injector
- Removing and installing the electronic unit injector sleeve
The procedures describe disconnecting hoses and tubes, removing and installing bolts, cleaning parts, and ensuring proper installation of seals and lubrication of parts. Tools required are listed for each procedure.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjkskedmme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
Caterpillar cat 428 c backhoe loader (prefix 2cr) service repair manual (2cr0...uuudfjjfjkkskm
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. The instructions include removing fuel lines, loosening nuts, removing nozzles and pumps, cleaning parts, and installing nozzles and pumps following specific tightening procedures and torque specifications. Safety notices are also provided to keep parts clean and contain fluids properly during the repair process.
The document provides instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing the fuel transfer pump from a Caterpillar 3306 engine. The procedures include:
- Turning off the fuel supply and disconnecting tubes and hoses
- Removing bolts and washers securing components and lifting parts off
- Checking condition of gaskets and installing new ones if needed
- Reinstalling components by securing with bolts and reconnecting tubes and hoses
The instructions emphasize cleaning parts and containing fluids during disassembly and reinstallation.
The document provides instructions for removing and installing several fuel system components on a Caterpillar 3304 engine, including:
- The fuel priming pump, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel filter base, which is removed by disconnecting fuel lines and removing mounting bolts. It is installed by reversing the removal steps.
- The fuel transfer pump, which is removed by disconnecting fuel lines and removing mounting bolts. Disassembly and assembly instructions are also provided.
Caterpillar cat 312 b excavator (prefix 8jr) service repair manual (8jr00001 ...fjsekksmemm
The documents provide instructions for servicing components of the engine in a 312B L excavator. It describes how to disassemble, inspect, and reassemble the water pump. The instructions include removing the water pump from the engine, disassembling it into individual parts like the impeller and shaft, inspecting parts for wear, replacing the seal if needed, and reassembling the water pump using the appropriate tools and specifications. Proper cleanup and installation procedures are emphasized to prevent contamination.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 322 c fm excavator (prefix c3r) service repair manual (c3r000...jfjskeksemmme
This document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR with a 3126B engine. The removal process involves disconnecting hoses and lines, removing bolts, and taking off the pump. Installation is the reverse of removal, and includes reconnecting hoses, bolts, and ensuring a tight seal. Proper cleaning and inspection of parts is emphasized. A separate section provides multi-step instructions for disassembling and assembling a turbocharger from the same excavator model.
This document provides instructions for removing and installing fuel transfer pumps and electronic unit injectors on a 345C Excavator. The removal process involves disconnecting hoses and tubes, removing bolts, and taking out the pump or injector. The installation is the reverse of removal. Special tools and cleaning of parts are required. Programming is also needed when installing a new electronic unit injector.
This document provides instructions for removing and installing fuel transfer pumps and electronic unit injectors on a 345C Excavator. The removal process involves disconnecting hoses and tubes, removing bolts, and taking out the pump or injector. The installation is the reverse of removal. Special tools and cleaning of parts are required. Programming is also needed when installing a new electronic unit injector.
This document provides instructions for removing and installing fuel transfer pumps and electronic unit injectors on a 345C Excavator. The removal process involves disconnecting hoses and tubes, removing bolts, and taking out the pump or injector. The installation is the reverse of removal. Special tools and cleaning of parts are required. Programming is also needed when installing new injectors to input identification codes.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjjseksxckmdme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...cfvdssd
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Inlet and exhaust valves - procedures for removing, installing, and related component removal and installation
- Valve guides - procedures for removing and installing guides
- Valve seat inserts - procedures for removing and installing inserts
- Engine oil filter base - procedures for removing, disassembling, and assembling the base
The document contains diagrams to illustrate the procedures and lists any required tools. Safety notices are included.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Inlet and exhaust valves - procedures for removing, installing, and related component removal and installation
- Valve guides - procedures for removing and installing guides
- Valve seat inserts - procedures for removing and installing inserts
- Engine oil filter base - procedures for removing, disassembling, and assembling the base
The document contains diagrams to illustrate the procedures and lists any required tools. Safety notices are included.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which involves using tooling to compress springs.
- Removing and installing valve guides using driver tools.
- Removing and installing valve seat inserts by extracting and driving them.
- Removing the engine oil filter base by disconnecting hoses and removing bolts.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
More Related Content
Similar to Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 and up)
This document provides instructions for removing and installing fuel transfer pumps and electronic unit injectors on a 345C Excavator. The removal process involves disconnecting hoses and tubes, removing bolts, and taking out the pump or injector. The installation is the reverse of removal. Special tools and cleaning of parts are required. Programming is also needed when installing a new electronic unit injector.
This document provides instructions for removing and installing fuel transfer pumps and electronic unit injectors on a 345C Excavator. The removal process involves disconnecting hoses and tubes, removing bolts, and taking out the pump or injector. The installation is the reverse of removal. Special tools and cleaning of parts are required. Programming is also needed when installing a new electronic unit injector.
This document provides instructions for removing and installing fuel transfer pumps and electronic unit injectors on a 345C Excavator. The removal process involves disconnecting hoses and tubes, removing bolts, and taking out the pump or injector. The installation is the reverse of removal. Special tools and cleaning of parts are required. Programming is also needed when installing new injectors to input identification codes.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjjseksxckmdme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...cfvdssd
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Inlet and exhaust valves - procedures for removing, installing, and related component removal and installation
- Valve guides - procedures for removing and installing guides
- Valve seat inserts - procedures for removing and installing inserts
- Engine oil filter base - procedures for removing, disassembling, and assembling the base
The document contains diagrams to illustrate the procedures and lists any required tools. Safety notices are included.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Inlet and exhaust valves - procedures for removing, installing, and related component removal and installation
- Valve guides - procedures for removing and installing guides
- Valve seat inserts - procedures for removing and installing inserts
- Engine oil filter base - procedures for removing, disassembling, and assembling the base
The document contains diagrams to illustrate the procedures and lists any required tools. Safety notices are included.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Valves, springs, and related parts are removed from the cylinder head using specialized tools.
- Valve guides are then removed and new guides installed at a specified depth in the cylinder head.
- Valve seat inserts are removed and new inserts installed using driver tools.
- The engine oil filter base and gasket are removed after disconnecting attached hoses and removing bolts.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
This document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which involves using tooling to compress springs.
- Removing and installing valve guides using driver tools.
- Removing and installing valve seat inserts by extracting and driving them.
- Removing the engine oil filter base by disconnecting hoses and removing bolts.
Similar to Caterpillar cat 345 c excavator (prefix mdc) service repair manual (mdc00001 and up) (20)
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjjseksxckmdme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, pistons, seals, and bearings.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 5rr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
1. Removing and installing the spacer plate, which involves removing seals and gaskets.
2. Removing and installing water directors by removing them from the cylinder head and pressing new ones in at a specified depth.
3. Removing and installing the lifter group using a magnetic tool and checking lifter diameters.
4. Removing and installing the camshaft by aligning timing marks, removing bolts and gears, cleaning parts, and reinstalling with lubricant while rotating to prevent binding.
Caterpillar cat d6 r track type tractor (prefix 5pr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing a spacer plate on a D6R track-type tractor with a 3306 engine. It describes removing the cylinder head, O-rings, seals, and spacer plate. It then details cleaning surfaces, installing new gaskets and seals, and reinstalling the spacer plate and cylinder head. The process also includes checking cylinder liner projection after installation.
Caterpillar cat d6 r track type tractor (prefix 5ln) service repair manual (5...fjjseksxckmdme
This document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines. It describes how to disassemble the governor by removing the fuel ratio control and mounting bolts. Proper cleaning of parts to prevent contamination is emphasized. The assembly procedure explains how to install bearings and other components in the fuel injection pump housing using various tools, and how to set the timing when installing the pump and governor.
Caterpillar cat d6 r track type tractor (prefix 4wr) service repair manual (4...fjjseksxckmdme
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torquing bolts and nuts to specified values after applying thread locking compound.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
This document provides disassembly and assembly instructions for a C18 industrial engine pump drive. It describes in detail how to disassemble and assemble the integral pump drive of a CX38-P892 petroleum transmission. The 19 step disassembly procedure includes removing bolts, gears, bearings, seals and other components. The 23 step assembly procedure describes cleaning parts and installing components in reverse order, paying attention to torque specifications and end play measurements. Tools required include lifting devices, pullers, indicators and other specialized tools.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and step-by-step procedures describing how to remove and install each component, with illustrations showing the parts.
3) Safety and cleaning notes are provided throughout to keep parts clean and avoid damage during disassembly and assembly.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure with 5 steps requiring identification marks for installation.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02247172
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02247178
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
Illustration 1 g01131526
1/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1. Position fuel transfer pump (4).
2. Install bolts (3).
3. Connect tube assemblies (2).
4. Connect hose assembly (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:21:50 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02258461
Electronic Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Pry Bar 1
Start By:
a. Remove the rocker shafts. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod
- Remove".
1/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01135732
1. Disconnect harness assembly (1) from electronic unit injector (2).
2. Remove bolt (3).
3. Position Tooling (A) under unit injector clamp (4) in order to remove electronic unit injector
(2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:22:47 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i03781931
Electronic Unit Injector - Install
SMCS - 1290-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B
9U-6862 Tapered Brush 1
9U-7237 Brush Extension 1
C
9U-6863 Small Bore Brush 1
9U-7237 Brush Extension 1
D 8T-2998 Lubricant 1
E
1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle 1
4C-4057 Tube 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Evacuate as much fuel and oil as possible from the cylinder head before installing the
injector. Several evacuations may be necessary. Use Tooling (E) to remove the fuel and oil
from the cylinder head.
Illustration 1 g01135874
2. Use Tooling (B) to clean injector seating (5) .
3. Use Tooling (C) to clean tip bore (6) .
Note: Do not reuse seals. Use new seals for installation.
4. Lubricate the bore lightly with a 50/50 mix of clean engine oil and Tooling (D) .
2/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01135732
Illustration 3 g01135876
5. When you install a new injector the E-Trim value must be programmed into the engine
control module. The injector confirmation code may need to be programmed into the engine
control module. E-Trim Value (X) is a twelve digit alphanumeric code that is supplied with
the data sheet that comes with the new injectors. Injector Confirmation Code (Y) is a four
digit numeric code. Both of the codes are located on the top of electronic unit injector (2) .
Use the following menu to program the E-Trim value.
◦ ECM Summary Screen
◦ Service Menu
◦ Calibration
3/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. ◦ Injector Code Calibration
NOTICE
When an electronic unit injector is replaced, the new electronic
injector code must be programmed into the engine's personality
module software by using the calibration menu on the Electronic
Service Tool. If the new electronic injector code is not entered, the
characteristics of the previous electronic unit injector is assumed.
If it is not possible to immediately reprogram the electronic injector
code into the personality module software, the engine will not be
severely harmed. The new electronic injector code should be
reprogrammed as quickly as possible in order to optimize engine
performance.
6. Install electronic unit injector (2) and unit injector clamp (4) .
Note: Use new bolt (3) .
7. Install bolt (3) .
8. Connect harness assembly (1) to electronic unit injector (2) . Tighten harness assembly (1)
to a torque of 2.50 ± 0.25 N·m (22 ± 2 lb in).
End By: Install the rocker shafts. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:23:43 UTC+0800 2020
4/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02370015
Electronic Unit Injector Sleeve - Remove
SMCS - 1713-011
Removal Procedure
Type 1
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
1/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
2. Drain the coolant from the cooling system into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity
of the cooling system. Refer to the Operation and Maintenance Manual, "Cooling System
Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System
Extended Life Coolant - Change".
Illustration 1 g01016237
3. Install Tooling (A) into electronic unit injector sleeve (1) .
4. Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head
assembly.
Type 2
2/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Table 2
Required Tools
Tool Part Number Part Description Qty
A (1)
221-9778 Puller Stud 1
128-7889 Bridge Puller 1
9U-6877 Thrust Bearing 1
5P-8247 Hard Washer 1
4K-0367 Nut 1
( 1 )
The tools that are listed in the chart are part of the 9U-6891 Injector Tool Group .
1. Remove the electronic unit injector. Refer to Disassembly and Assembly , "Electronic Unit
Injector - Remove".
2. Drain the coolant from the cooling system into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity
of the cooling system. Refer to the Operation and Maintenance Manual, "Cooling System
Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System
Extended Life Coolant - Change".
3/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01016237
3. Install the puller stud from Tooling (A) into unit injector sleeve (1) .
4. Install the following parts from Tooling (A) over the stud: bridge puller, thrust bearing, hard
washer and nut.
5. Tighten the nut until unit injector sleeve (1) is pulled free of the cylinder head assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:24:40 UTC+0800 2020
4/4
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02370001
Electronic Unit Injector Sleeve - Install
SMCS - 1713-012
Installation Procedure
Type 1
Table 1
Required Tools
Tool Part Number Part Description Qty
B 4C-5552 Large Bore Brush 1
C
9U-7237 Brush Extension 1
9U-7244 End Brush 1
D 9U-7258 Driver Cap 1
E 4C-9507 Retaining Compound 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01131579
1. Use Tooling (B) to clean the electronic unit injector bore.
2. Use Tooling (C) to clean the electronic unit injector seat.
3. Apply Tooling (E) to upper land (2) and lower land (3) on the electronic unit injector sleeve.
2/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01016237
4. Position electronic unit injector sleeve (1) in the cylinder head assembly. Use Tooling (D)
and a hammer to seat the sleeve.
5. Install the electronic unit injectors. Refer to Disassembly and Assembly , "Electronic Unit
Injector - Install".
6. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual,
"Capacities (Refill)" for the cooling system capacity. Refer to Operation and Maintenance
Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance
Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure.
Type 2
Table 2
Required Tools
Tool Part Number Part Description Qty
B 9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
3/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4C-5552 Large Bore Brush 1
C (1)
221-9778 Puller Stud 1
D (1)
9U-7258 Driver Cap 1
E 4C-9507 Retaining Compound -
( 1 )
Part of the 9U-6891 Injector Tool Group
1. Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
NOTICE
Ensure that the electronic unit injector sleeve and the cylinder head
bore are completely free of oil, dirt, and sealant debris.
Illustration 3 g01120522
2. Install new O-ring seals (2) on electronic unit injector sleeve (1) .
Note: Do not apply Tooling (E) to the cylinder head surfaces. Apply Tooling (E) on the
electronic unit injector sleeve only.
3. Apply Tooling (E) to the contact surface of electronic unit injector sleeve (1) on the surface
that is marked "X".
4. Lubricate O-ring seals (2) with clean engine oil.
4/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01076119
5. Install Tooling (C) into the threads of electronic unit injector sleeve (1) .
6. Position Tooling (C) and the electronic unit injector sleeve in the cylinder head. Use care
not to damage the O-ring seal on the electronic unit injector sleeve.
7. Use Tooling (D) and a hammer to install electronic unit injector sleeve (1) in the cylinder
head.
NOTICE
Ensure that the electronic unit injector sleeve is properly seated in the
cylinder head. The Tooling will "RING" when the electronic unit
injector sleeve is fully seated in the bore of the cylinder head.
8. Remove Tooling (D) and Tooling (C) . Use a clean towel and remove excess Tooling (E) .
9. Install the electronic unit injector. Refer to Disassembly and Assembly , "Electronic Unit
Injector - Install".
10. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual,
"Capacities (Refill)" for the cooling system capacity. Refer to Operation and Maintenance
Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance
Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:25:37 UTC+0800 2020
5/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02247321
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities
and Recommendations".
1/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01131603
2. Disconnect hose assemblies (3), (4), and (6).
3. Disconnect tube assembly (5).
1. Remove nuts (1).
2. Remove turbocharger (2) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:26:34 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i04001168
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01131603
1. Apply Tooling (A) to the turbocharger mounting studs on the exhaust manifold.
2. Position the gasket and turbocharger (2) on the engine.
Note: Discard the nuts after use. Use new nuts for installation.
3. Install nuts (1).
4. Connect tube assembly (5).
5. Connect hose assemblies (3), (4), and (6).
6. Fill the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and
Recommendations".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 07:27:30 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR MDC
Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i07024212
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Start By:
1/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. a. Remove the high-pressure turbocharger. Refer to Disassembly and Assembly,
"Turbocharger - Remove".
b. Remove the precooler. Refer to Disassembly and Assembly, "Precooler - Remove".
c. Remove the low-pressure turbocharger. Refer to Disassembly and Assembly, "Turbocharger
- Remove".
Illustration 1 g06199242
1. Remove the lower bracket for the precooler, the upper bracket for the precooler, and the
middle bracket for the precooler.
2. Remove bracket (1).
Illustration 2 g06199244
3. Remove locknuts (2) and the spacers. Remove exhaust manifold (3) and the gaskets.
2/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 3 g06199252
4. If necessary remove studs (4).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite MR2000 -
B
- Loctite C5-A -
- Loctite 8008(1)
-
(1)
For use in EAME only
Illustration 4 g06199252
1. Install studs (4). Tighten studs (4) to a torque of 35 ± 5 N·m (26 ±4 lb ft)
3/5
ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...