Caterpillar Cat 236B SKID STEER LOADER (Prefix HEN) Service Repair Manual (HEN06750 and up).pdf

Service Repair Manual
Models
Caterpillar Cat 236B
SKID STEER LOADER

Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 236B SKID STEER LOADER HEN
Configuration: 236B2 Skid Steer Loader HEN06750-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
C3.4 Engines for Caterpillar Built Machines
Media Number -KENR6941-04 Publication Date -01/03/2012 Date Updated -01/03/2012
i02639290
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
236B2 Skid Steer Loader HEN06750-UP (MACHINE) POWERED BY 3044C Engine...
2019/10/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01345395
Typical example
1. Loosen the nuts and adjustment screws (1) on all rocker arms.
2. Remove bolts (5) .
3. Progressively loosen bolts (3). Begin at the ends of the rocker shaft assembly and work
toward the center.
Note: Damage to the rocker shaft may occur if the long bolts are loosened first. To avoid
distortion of the rocker shaft assembly, each bolt should be loosened by a quarter of a turn at
one time. Repeat the procedure until all bolts are loosened.
4. Remove bolts (3) .
5. Remove rocker shaft assembly (2) from the cylinder head.
6. Place temporary identification marks on pushrods (4) and pads (6) .
Note: Identification will ensure that the pushrods and pads can be reinstalled in the correct
position. Do not interchange the positions of used pushrods or pads.
7. Remove pushrods (4) from the cylinder head. Remove pads (6) from the valve stems.
2/3
2019/10/24

Shutdown SIS
Previous Screen
i02639287
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Remove".
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
1/3
2019/10/24

1. Make an identification mark on each rocker arm assembly in order to show the location.
Note the mark at position (X) for installation purposes.
Note: The components must be reinstalled in the original location. Do not interchange
components.
2. Use Tooling (A) to remove retaining rings (8) .
2/3
2019/10/24

3. Remove rocker arm assembly (5) .
4. Remove pedestal (6) from rocker shaft (3) .
5. Remove rocker arm assembly (7) .
6. Remove spring (4) .
7. Repeat Steps 3 through 6 in order to remove the remaining rocker arm assemblies from
rocker shaft (3) .
8. If necessary, remove nuts (1) and adjusters (2) from the rocker arms. Make a temporary
identification mark on each adjuster in order to show the location.
Note: The components must be reinstalled in the original location. Do not interchange
components.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 24 13:23:45 UTC+0800 2019
3/3
2019/10/24

Shutdown SIS
Previous Screen
i02639289
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
Table 1
Required Tools
A 1P-1855 Retaining Ring Pliers 1
1. Ensure that all components are clean and free from wear or damage. Refer to Specifications,
"Rocker Shaft" for more information. If necessary, replace any components that are worn or
damaged.
Note: Ensure that all oil holes are free from blockages.
2. Lubricate all of the components with clean engine oil before assembly.
1/3
2019/10/24

3. If necessary, install nuts (1) and adjusters (2) to rocker arm assemblies (5) and (7). If the
original adjusters are reused, ensure that the adjusters are installed in the original positions.
4. Use Tooling (A) to install retaining ring (8) to the front end of rocker shaft (3). The front
end of the rockershaft is identified by the mark at Position (X). Ensure that the mark at
position (X) is upward.
5. Install rocker arm assembly (5) to rocker shaft (3) .
6. Install bracket (6) to rocker shaft (3) .
Note: Ensure correct orientation of the bracket. Refer to Illustration 1.
7. Install rocker arm assembly (7) to rocker shaft (3) .
2/3
2019/10/24

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8. Install spring (4) to rocker shaft (3) .
9. Repeat Steps 5 through 8 in order to assemble the remaining components of the rocker shaft
assembly.
10. Use Tooling (A) to install retaining ring (8) to the rear end of rocker shaft (3) .
End By: Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Install".
Thu Oct 24 13:24:44 UTC+0800 2019
3/3
2019/10/24

Shutdown SIS
Previous Screen
i02639286
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
1. Ensure that all components are clean and free from wear or damage. Refer to Specifications,
"Rocker Shaft" for more information. Replace any components that are worn or damaged.
1/3
2019/10/24

Typical example
2. Apply clean engine lubricating oil to both ends of pushrods (4). Install the pushrods to the
engine with the cup upward. Ensure that the pushrods are installed correctly in the socket of
the valve lifters.
Note: If the pushrods have been used, ensure that the pushrods are installed in original
positions.
3. Lubricate the top of the valve stems with clean engine oil. Install caps (6) to the valve
stems.
Note: If the caps have been used, ensure that the caps are installed in original positions.
4. Install rocker shaft (2) to the cylinder head.
Note: Ensure that the ends of adjustment screws (1) are correctly seated in ends of pushrods
(4). Also ensure that valve caps (6) are in position under the rocker arms.
5. Install bolts (3) to the rocker shaft. Tighten the bolts to a torque of 15 N·m (11 lb ft). Begin
at the center of the rocker shaft assembly and work outward.
Note: Damage to the rockershaft may occur if the short bolts are tightened first.
6. Install bolts (5) to the rocker shaft. Tighten the bolts to a torque of 15 N·m (11 lb ft).
2/3
2019/10/24

7. Adjust the valve lash. Refer to Systems Operation, Testing and Adjusting, "Engine Valve
Lash - Inspect/Adjust" for the correct procedure.
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Thu Oct 24 13:25:44 UTC+0800 2019
3/3
2019/10/24

Shutdown SIS
Previous Screen
i02639291
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
A
138-7575 Link Bracket 2
8T-4189 Bolt 2
8T-4121 Hard Washer 2
Start By:
A. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
B. Remove the fuel injectors. Refer to Disassembly and Assembly, "Fuel Injectors - Remove
and Install".
C. Remove the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and
Install".
D. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Remove".
NOTICE
1/6
2019/10/24

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct procedure.
Typical example
2. Disconnect hose (2) from water temperature regulator housing (1) .
2/6
2019/10/24

3. Remove breather hose (4) .
4. If necessary, remove inlet manifold (3). Refer to Disassembly and Assembly, "Inlet
Manifold - Remove and Install".
The cylinder head tightening sequence
3/6
2019/10/24

5. Gradually loosen cylinder head bolts (5) in reverse numerical order to the sequence that is
shown in Illustration 2. This will prevent distortion of the cylinder head.
6. Remove cylinder head bolts (5) from cylinder head (6) .
7. Attach Tooling (A) and a suitable lifting device to cylinder head (6). Carefully lift the
cylinder head off the cylinder block. The weight of the cylinder head is approximately 34 kg
(75 lb).
Note: Do not use a lever to separate the cylinder head from the cylinder block. Take care
not to damage the machined surfaces of the cylinder head during the removal procedure.
Avoid contamination of the cylinder bores with coolant or with debris.
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
8. Remove gasket (7) .
4/6
2019/10/24

9. Note the position of dowels (8) in the cylinder block. Do not remove the dowels unless the
dowels are damaged.
5/6
2019/10/24

Typical example
10. If necessary, remove bolts (11) and remove lifting bracket (10). Remove joint (9) .
11. If necessary, remove water temperature regulator housing (1). Refer to Disassembly and
Assembly, "Water Temperature Regulator Housing - Remove and Install".
Thu Oct 24 13:26:43 UTC+0800 2019
6/6
2019/10/24

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
i05228990
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
A
138-7575 Link Bracket 2
8T-4189 Bolt 2
8T-4121 Hard Washer 2
B -
Guide Bolt
(M12 x 1.75 by 100 mm)
2
C - Straight Edge 1
NOTICE
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block. Ensure
that there is no debris in the cylinder bores, the coolant passages, or the lubricant passages.
2. Inspect the mating surface of the cylinder head for distortion. Refer to Specifications,
"Cylinder Head" for more information.
1/6
2019/10/24

3. Inspect dowels (8) for damage. If necessary, replace the dowels in the cylinder block.
4. Install Tooling (B) to the cylinder block. Refer to Illustration 1.
2/6
2019/10/24

Typical example
5. If necessary, install a new joint (9) , lifting bracket (10) and bolts (11) to cylinder head (6) .
Tighten the bolts to a torque of 11 N·m (97 lb in).
6. Align cylinder head gasket (7) with Tooling (B) and install the cylinder head gasket onto the
cylinder block.
Note: Ensure that the word UP on the cylinder head gasket is upward.
7. Use Tooling (A) and a suitable lifting device to lift cylinder head (6) . The weight of the
cylinder head is approximately 34 kg (75 lb). Align cylinder head (6) with Tooling (B) and
install the cylinder head to the cylinder block.
Note: Ensure that the cylinder head is correctly seated on dowels (8) .
8. Remove Tooling (B) .
3/6
2019/10/24

9. Clean cylinder head bolts (5) . Inspect the threads of the bolts. Use Tooling (C) in order to
check the bolts. The bolts must be renewed if there is any visual reduction in the diameter
over area (X) .
10. Lubricate the threads and the shoulder of cylinder head bolts (5) with clean engine oil
before installation.
11. Install cylinder head bolts (5) to cylinder head (6) .
The cylinder head tightening sequence
4/6
2019/10/24

12. Tighten cylinder head bolts (5) in numerical order to the sequence that is shown in
Illustration 5. Tighten the cylinder head bolts to a torque of 118 ± 5 N·m (87 ± 4 lb ft).
Typical example
13. If necessary, install water temperature regulator housing (1) . Refer to Disassembly and
Assembly, "Water Temperature Regulator Housing - Remove and Install".
14. Connect hose (2) to water temperature regulator housing (1) .
15. If necessary, install inlet manifold (3) . Refer to Disassembly and Assembly, "Inlet Manifold
- Remove and Install".
16. Install breather hose (4) .
17. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Install".
18. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Change" for the correct procedure.
5/6
2019/10/24

Caterpillar Cat 236B SKID STEER LOADER (Prefix HEN) Service Repair Manual (HEN06750 and up).pdf

Recommended

Recommended

More Related Content

More from f8usjejkdmmd

More from f8usjejkdmmd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 236B SKID STEER LOADER (Prefix HEN) Service Repair Manual (HEN06750 and up).pdf