Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
301.6C and 301.8C
Mini Hydraulic Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 301.8C MINI HYD EXCAVATOR JSB
Configuration: 301.6C & 301.8C Mini Hydraulic Excavators JSB00001-UP (MACHINE) POWERED BY L3E Engine
Disassembly and Assembly
301.6C and 301.8C
Mini Hydraulic Excavators
Machine Systems
Media Number -RENR9157-01 Publication Date -01/11/2005 Date Updated -06/12/2005
i02355300
Front Idler - Remove and Install
SMCS - 4159-010
Removal Procedure
Start By:
A. Remove the front idler, the recoil spring, and the hydraulic track adjuster. Refer to
Disassembly and Assembly, "Front Idler, Recoil Spring and Hydraulic Track Adjuster -
Remove and Install".
1/3
301.6C & 301.8C Mini Hydraulic Excavators JSB00001-UP (MACHINE) POWERED...
2020/3/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

Illustration 1 g01176420
1. Remove bolts (4) and spring assembly (2).
2. Remove bolts (1), supports (5), and front idler (3) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-3263 Thread Lock Compound 1
2/3
2020/3/8

1. Apply Tooling (A) to bolts (1) and (4) .
2. Position front idler (3) and supports (5). Install bolts (1) .
3. Position spring assembly (2) and install bolts (4) .
End By: Install the front idler, the recoil spring, and the hydraulic track adjuster. Refer to
Disassembly and Assembly, "Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Mar 8 13:44:30 UTC+0800 2020
3/3
2020/3/8

Shutdown SIS
Previous Screen
301.6C and 301.8C
Machine Systems
i02355327
Hydraulic Track Adjusters - Remove and Install
SMCS - 4157-010
Removal Procedure
Start By:
A. Remove the front idler, the recoil spring, and the hydraulic track adjuster. Refer to
Disassembly and Assembly, "Front Idler, Recoil Spring and Hydraulic Track Adjuster -
Remove and Install".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1/3
2020/3/8

1. Remove track adjuster (1) .
2. Remove seal (2). Remove ring (3) and O-ring seal (4) .
3. Remove bolts (8), plates (6) and (7), and grease fitting (5) .
Table 1
Required Tools
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
2/3
2020/3/8

1. Apply Tooling (A) to bolts (9) .
2. Position plates (6) and (7). Install bolts (8) and grease fitting (5) .
3. Install ring (3) and O-ring seal (4). Install seal (2) .
4. Install track adjuster (1) .
End By: Install the front idler, the recoil spring, and the hydraulic track adjuster. Refer to
Disassembly and Assembly, "Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove
and Install".
Sun Mar 8 13:45:27 UTC+0800 2020
3/3
2020/3/8

Shutdown SIS
Previous Screen
301.6C and 301.8C
Machine Systems
i02355301
Sprocket - Remove and Install
SMCS - 4164-010
Removal Procedure
Start By:
A. Remove the track. Refer to Disassembly and Assembly, "Track - Remove and Install".
1. Remove bolts (1) and sprocket (2) .
Table 1
Required Tools
1/2
2020/3/8

1. Apply Tooling (A) to bolts (1) .
2. Position sprocket (2) and install bolts (1) .
End By: Install the track. Refer to Disassembly and Assembly, "Track - Remove and Install".
Sun Mar 8 13:46:24 UTC+0800 2020
2/2
2020/3/8

Shutdown SIS
Previous Screen
301.6C and 301.8C
Machine Systems
i02360053
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
Removal Procedure
Table 1
Required Tools
A 138-7575 Link Bracket 1
Start By:
A. Remove the track. Refer to Disassembly and Assembly, "Track - Remove and Install".
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of
the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/3
2020/3/8

Dispose of all fluids according to local regulations and mandates.
1. Drain the hydraulic tank into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Hydraulic System Oil - Change".
2. Remove cover (1) .
3. Disconnect hose assemblies (2) .
2/3
2020/3/8

4. Attach Tooling (A) and a suitable lifting device to the final drive and travel motor (4). The
weight of the final drive and travel motor (4) is approximately 27 kg (60 lb). Remove bolts
(3) and the final drive and travel motor (4) .
Sun Mar 8 13:47:20 UTC+0800 2020
3/3
2020/3/8

Shutdown SIS
Previous Screen
301.6C and 301.8C
Machine Systems
i02355294
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
A 1P-1857 Retaining Ring Pliers 1
B 8B-7554 Bearing Cup Puller Gp 1
C 1P-1855 Retaining Ring Pliers 1
D 1P-1859 Retaining Ring Pliers 1
E 1P-1863 Retaining Ring Pliers 1
F 154-6181 Forcing Screw 2
Start By:
A. Remove the track motor. Refer to Disassembly and Assembly, "Final Drive and Travel
Motor - Remove".
1/12
2020/3/8

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (1) and the O-ring seal.
2. Remove spring (4) and washer (3) .
3. Remove spool (2) .
4. Repeat Steps 1 through Steps 2 for the opposite side.
2/12
2020/3/8

5. Remove bolts (5) and head assembly (6) .
6. Remove bearing (7) .
3/12
2020/3/8

7. Remove port plate (8) .
8. Remove barrel assembly (9) .
4/12
2020/3/8

9. Remove piston (10), retaining plate (11), and bearing (12) .
10. Remove pins (13) .
11. Use a suitable press and Tooling (A) in order to remove retaining ring (14) .
5/12
2020/3/8

12. Remove washers (15) and spring (16) .
13. Remove O-ring seal (17) and swashplate (18) .
6/12
2020/3/8

14. Remove balls (19), pistons (20), and the springs.
15. Remove retaining ring (21) and cover (22) .
16. Remove sun gear (24) and carrier (23) .
7/12
2020/3/8

17. Use Tooling (C) in order to remove retaining ring (25) .
18. Remove washers (26), gears (27), and washers (28) .
19. Use Tooling (D) in order to remove retaining ring (30) .
20. Remove sun gear (29) .
8/12
2020/3/8

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

21. Use Tooling (D) in order to remove retaining rings (31) .
22. Use Tooling (B) in order to remove gears (32) .
23. Use Tooling (E) in order to remove retaining ring (33) .
9/12
2020/3/8

Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Service Repair Manual Instant Download.pdf (7)

More from f8usejkdmmd8i

More from f8usejkdmmd8i (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Service Repair Manual Instant Download.pdf