Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
320C LN EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR AXK
Configuration: 320C LN Excavator AXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2019/10/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
2/5(W)
w
2019/10/9

3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5(W)
w
2019/10/9

8. Use Tool (B) to remove front oil seal (8) (not shown) from the front housing.
Note: Illustration 6 does not show that the front seal (8) is removed.
9. Remove set screw (9) from the front housing.
4/5(W)
w
2019/10/9

Note: Illustration 7 does not show that the front seal (8) is removed.
10. Remove spindle (10) and idler gear (11) as an assembly. Push on the gear with a hardwood
bar (12) through the mounting hole for the front seal. Rotate the gear while the gear is
pushed.
Note: Use care not to damage the pump idler gear and the crankshaft gear.
Note: Replace the drive gear and the driven gear as an assembly.
Note: Do not attempt to reuse the oil pump gear and drive gear assembly. Replace the oil pump
gear and the drive gear assembly with new parts.
Note: Check all of the gears for worn teeth or damaged teeth. Replace the gears, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 9 13:10:22 UTC+0800 2019
5/5(W)
w
2019/10/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01146555
Engine Oil Pump - Install
SMCS - 1304-012
Installation Procedure
Table 1
Required Tools
A 1P-0510 Driver Group 1
NOTICE
1/5(W)
w
2019/10/9

1. Use Tool (A) to install the front oil seal (8) (not shown).
2. Lower the temperature of the spindle (10). Install spindle (10) and idler gear (11) as an
assembly in the front housing.
Note: The temperature of the spindle is lowered in order to ease the installation of the
spindle in the front housing.
3. Install set screw (9) in the front housing.
2/5(W)
w
2019/10/9

4. Lower the temperature of the drive gear assembly. Install drive gear (7) in the front housing.
Note: The temperature of the drive gear assembly is lowered in order to ease the installation
of the drive gear assembly in the front housing.
Always wear protective gloves when handling parts that have been
heated.
3/5(W)
w
2019/10/9

5. Heat the oil pump gear up to 180 to 220 °C (356 to 428 °F). Support end (X) of the shaft (7)
(drive gear). Install oil pump gear (6) onto the shaft. The end of the gear (Z) should be flush
with the end of the shaft (Y) .
6. Install driven gear (4) into the front housing (slip fit).
7. Place gasket (3) and cover (2) in position on the front housing.
Note: Ensure that the old gasket material is removed from the mating surfaces.
8. Install the washer and bolt (1) that secures the cover to the front housing. Tighten bolt (1) to
a torque of 34 ± 5 N·m (25 ± 4 lb ft).
Refer to the Specifications Module, "Engine Oil Pump" for more information on the engine oil
pump.
End By: Install the front housing. Refer to Disassembly and Assembly, " Housing (Front) -
Install".
4/5(W)
w
2019/10/9

Wed Oct 9 13:11:18 UTC+0800 2019
5/5(W)
w
2019/10/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01149671
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
A. Remove V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
1/2(W)
w
2019/10/9

NOTICE
containing fluids.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
2. Remove four bolts (1) that secure the water pump to the engine.
3. Remove water pump pulley (2) and water pump (3) as an unit from the engine.
4. Remove O-ring (4) (not shown) from water pump (3). Discard the old O-ring.
Wed Oct 9 13:12:13 UTC+0800 2019
2/2(W)
w
2019/10/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01566087
Water Pump - Disassemble
SMCS - 1361-015
Disassembly Procedure
Table 1
Required Tools
A 1P-2321 Combination Puller 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Group 1
Start By:
A. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
NOTICE
Always wear protective gloves when handling parts that have been
heated.
Note: If the water pump is heated up to 80 °C (176 °F), the components can be easily removed.
1/4(W)
w
2019/10/9

1. Remove four bolts (1) and the washers that secure the water pump pulley to the water pump.
2. Remove water pump pulley (2) from the water pump.
Note: Check the groove for the V-belt of the water pump pulley for wear and damage. Replace the
water pump pulley, if necessary.
Note: Use Tool (C) during disassembly procedures of the water pump, which require the use of a
press or a hammer.
3. Use Tool (A) to remove flange (3) from the water pump.
2/4(W)
w
2019/10/9

4. Use Tool (B) to remove retaining ring (4) from the water pump.
5. Use a press and Tool (C) to remove shaft assembly (5) from water pump assembly (6) .
3/4(W)
w
2019/10/9

6. Remove impeller (8) from the shaft assembly (5) .
Note: Check the impeller for wear, corrosion, and metal to metal contact. Replace the impeller, if
necessary.
7. Remove the following items from shaft (9) :
◦ Bearing (10)
◦ Spacer (11)
◦ Bearing (12)
◦ Washer (13)
8. Once all of the components have been removed, then check shaft (9) for distortion. Replace the shaft,
if necessary.
9. Check seal (14) for wear and damage. Use Tool (C) in order to remove the seal from the water pump
housing, if necessary.
Note: Replace the seal if any signs of leakage occurs during the operation of the water pump.
10. Replace O-ring (7) with a new O-ring.
Wed Oct 9 13:13:09 UTC+0800 2019
4/4(W)
w
2019/10/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01566223
Water Pump - Assemble
SMCS - 1361-016
Assembly Procedure
Table 1
Required Tools
A 1P-0510 Driver Group 1
B 1P-1861 Retaining Ring Pliers 1
Note: Refer to Specifications, "Water Pump" for specifications that are required during assembly.
1/4(W)
w
2019/10/9

1. Install seal (14), if the seal was removed during the disassembly procedures.
2. The following components are installed on shaft (9) :
◦ Washer (13)
◦ Bearing (12)
◦ Spacer (11)
◦ Bearing (10)
Note: Check two bearings (10) and (12) for correct rotation.
2/4(W)
w
2019/10/9

3. Use a press and Tool (A) to install shaft assembly (5) into the water pump housing.
4. Use a press and Tool (A) to install impeller (8) onto shaft assembly (5) .
5. Use Tool (B) to install retaining ring (4) into the water pump housing.
6. Use a press and Tool (A) to install flange (3) onto shaft assembly (5) .
3/4(W)
w
2019/10/9

7. Install water pump pulley (2) onto the flange.
8. Install four bolts (1) in order to secure water pump pulley (2) to the flange.
End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Wed Oct 9 13:14:05 UTC+0800 2019
4/4(W)
w
2019/10/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01149732
Water Pump - Install
SMCS - 1361-012
NOTICE
1. Replace O-ring (4) (not shown) with a new part. Apply glycerine to the O-ring before the
installation of the water pump (3) and water pump pulley (2) .
1/2(W)
w
2019/10/9

2. Install the water pump (3) and water pump pulley (2) as a unit onto the engine.
Note: When the water pump is installed, ensure that the grease fitting is up. Also, ensure
that the weep hole is down.
3. Install bolts (1) in order to secure water pump (3) to the cylinder block.
4. Fill the cooling system to the correct level. Refer to the appropriate Operation and
Maintenance Manual for the correct fluid and the correct filling procedure.
End By: Install V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Wed Oct 9 13:15:00 UTC+0800 2019
2/2(W)
w
2019/10/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01148678
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
filler cap is cool enough to touch with the bare hand.
Remove the filler cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with skin and
eyes to prevent personal injury.
NOTICE
NOTICE
1/4(W)
w
2019/10/9

containing fluids.
1. Drain the coolant level below the water temperature regulator.
2. Loosen hose clamp (1) and disconnect hose (2) from cover (4) of the water temperature
regulator.
3. Remove two bolts (3) and the washers from cover (4) of the water temperature regulator.
4. Separate cover (4) from elbow (5) .
5. Remove bolts (6). Separate elbow (5) from the water outlet manifold.
6. Remove water temperature regulator (8) (not shown) from cover (4) .
7. Remove gasket (7) (not shown) and gasket (9) (not shown) from the mounting surfaces of
cover (4) and elbow (5) .
8. Use the following procedure in order to test the water temperature regulator:
a. Put the water temperature regulator in a tub of water. Heat the water in order to test
the water temperature regulator for thermostatic action.
Note: Stir the water in the tub in order to maintain even temperature during the test.
2/4(W)
w
2019/10/9

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

b. When the valve of the water temperature regulator lifts more than 10 mm (0.4 inch),
measure the water temperature.
Note: The opening temperature for the water temperature regulator is 71° ± 2°C (160°
± 3.6°F).
c. If the valve fails to operate properly, replace the water temperature regulator.
NOTICE
1. Clean all of the mounting surfaces for the gaskets and remove all gasket material.
NOTICE
If the water temperature regulator is installed incorrectly, it will cause
the engine to overheat.
2. Install water temperature regulator (8) (not shown) into elbow (5) .
Note: When the water temperature regulator is installed, ensure that the hole for the air vent
is up.
3. Install gasket (7) (not shown) and gasket (9) (not shown).
3/4(W)
w
2019/10/9

Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual Instant Download.pdf (14)

More from f8seodkdmdmed3

More from f8seodkdmdmed3 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 320C LN EXCAVATOR (Prefix AXK) Service Repair Manual Instant Download.pdf