Caterpillar Cat 160M 3 AWD MOTOR GRADER (Prefix N9T) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
160M 3 AWD MOTOR GRADER

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 160M 3 AWD MOTOR GRADER N9T
Configuration: 160M Series 3 Motor Grader-All Wheel Drive N9T00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Machine Systems
Media Number -UENR3488-02 Publication Date -01/09/2018 Date Updated -24/09/2018
i02649335
Piston Pump (Hydraulic and Steering) - Assemble
SMCS - 4306-016; 5070-016
Assembly Procedure
Illustration 1 g01330063
1. Install lip seal (48).
2. Use Tooling (C) in order to install retaining ring (49).
3. Install lip seal (50).
1/7
160M Series 3 Motor Grader-All Wheel Drive N9T00001-UP (MACHINE) POWERE...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

4. Install screws (45), bearings (44), bearing cone (46), and bearing cup (47).
5. Install swashplate (43).
6. Install shaft (37).
7. Install plug (36).
8. Install dowel (28).
2/7
2019/12/28

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
9. Install washer (31), spring (30), and washer (29).
10. Use Tooling (A), Tooling (B) and a suitable press in order to install retaining ring (32) onto
barrel (27).
11. Install pistons (42) into retainer (41) and barrel (27).
3/7
2019/12/28

12. Install barrel (27).
13. Install shim (26) and bearing cone (25).
4/7
2019/12/28

14. Position plates (40) and plates (38).
15. Install bolts (39).
16. Install piston (22), piston (21), spring (24), gasket (19), port plate (20), and bearing cup
(23).
5/7
2019/12/28

injury.
17. Install bolts (17) and head (18).
injury.
18. Install retainer (15), spring (14), rod (13), retainer (12), spool (11), plug (10), and the O-ring
seal. Install plug (16) and the O-ring seal.
19. Install retainer (8), spring (7), retainer (6), spool (5), plug (4), and the O-ring seal. Install
plug (9) and the O-ring seal.
6/7
2019/12/28

20. Install O-ring seals (3).
21. Install bolts (1) and valve (2).
End By:
a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic and
Steering) - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 16:49:53 UTC+0800 2019
7/7
2019/12/28

Shutdown SIS
Previous Screen
i05818515
Piston Pump (Hydraulic and Steering) - Install
SMCS - 4306-012; 5070-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
1. Install O-ring seal (9) to piston pump (7).
1/3
2019/12/28

2. Attach a suitable lifting device to piston pump (7). The weight of piston pump (57) is
approximately 52 kg (115 lb). Use the suitable lifting device in order to position piston
pump (7) to the machine.
3. Install bolts (8).
4. Connect hose assembly (4) and (5). Connect bracket assembly (6).
2/3
2019/12/28

5. Connect harness assembly (1). Connect hose assemblies (2) and (3).
End By:
a. Install the piston pump (hydraulic fan). Refer to Disassembly and Assembly, "Piston Pump
(Hydraulic Pump)- Install".
Sat Dec 28 16:50:49 UTC+0800 2019
3/3
2019/12/28

Shutdown SIS
Previous Screen
i05819040
Piston Pump (All Wheel Drive) - Remove
SMCS - 5070-011-YW
Removal Procedure
Start By:
a. Remove the rear chassis support. Refer to Disassembly and Assembly, "Rear Chassis
Support - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/3
2019/12/28

1. Disconnect fitting (1). Disconnect hose assemblies (2) and (3).
2. Disconnect hose assemblies (4) and (6). Disconnect hose (5).
3. Disconnect harness assemblies (7) and (8). Disconnect hose assemblies (9).
2/3
2019/12/28

4. Attach suitable lifting devices to all wheel drive piston pumps (10). The weight of all wheel
drive piston pumps (10) is approximately 111 kg (245 lb).
5. Remove bolts (11) and all wheel drive piston pumps (10).
Sat Dec 28 16:51:44 UTC+0800 2019
3/3
2019/12/28

Shutdown SIS
Previous Screen
i02747416
Piston Pump (All Wheel Drive) - Disassemble
SMCS - 5070-015-YW
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump (All Wheel Drive) -
Remove".
1/8
2019/12/28

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (28), bolts (27), housing (23), and bearing (19).
2. Use Tooling (A) in order to remove retaining ring (26).
3. Remove O-ring seal (5), cover (10), retaining ring (6), shaft (7), and bearing (8).
2/8
2019/12/28

5. Remove gear (20), annular gear (21), coupling (11), key (12), and O-ring seal (22).
6. Remove plug (1), shims (2), spring (3), piston (4), sleeve (17), and O-ring seal (18).
7. Remove cap (15), O-ring seal (14), adapter (13), and O-ring seal (16).
8. Remove plug (25) and O-ring seal (24).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
3/8
2019/12/28

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove bolts (37), O-ring seal (29), O-ring seal (31), coupling (30), cover (34), and bearing (32).
11. Remove gear (40), annular gear (41), coupling (35), key (36), and O-ring seal (42).
12. Remove bearing (39).
14. Remove plug (38) and the O-ring seal.
15. Remove plug (54), shims (53), spring (52), piston (51), sleeve (50), and O-ring seal (49).
16. Remove cap (46), O-ring seal (47), adapter (45), and O-ring seal (44) from housing (43).
4/8
2019/12/28

Caterpillar Cat 160M 3 AWD MOTOR GRADER (Prefix N9T) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 160M 3 AWD MOTOR GRADER (Prefix N9T) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 160M 3 AWD MOTOR GRADER (Prefix N9T) Service Repair Manual Instant Download.pdf (18)

More from f8seodkdmdmed3

More from f8seodkdmdmed3 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 160M 3 AWD MOTOR GRADER (Prefix N9T) Service Repair Manual Instant Download.pdf