This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists required tools and outlines 33 steps to remove components like plugs, springs, seals, gears, and housings. Safety notices warn of hazards like stored spring energy and hydraulic fluid pressure. The process separates the final drive, travel motor, and individual internal parts to facilitate repair or replacement.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It describes 33 steps to remove components such as plugs, springs, seats, spools, adapters, valves and seals. Special care must be taken when removing pressurized components to avoid injury from parts propelled by released spring forces. Cleanliness is important to prevent contamination during disassembly.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists the required tools and presents a step-by-step process involving removing bolts, seals, gears, and other components. Safety notices are included to handle fluids properly and avoid injury from hydraulic pressure. The disassembly procedure removes the outer casing pieces and individually dismantles the internal gear and shaft assemblies.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings using various specialized tools. Safety warnings are provided regarding potential hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings. Safety notices are provided throughout to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and released spring forces. Tools required for the disassembly are also listed.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids or heavy components during the disassembly process.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It describes 33 steps to remove components such as plugs, springs, seats, spools, adapters, valves and seals. Special care must be taken when removing pressurized components to avoid injury from parts propelled by released spring forces. Cleanliness is important to prevent contamination during disassembly.
This document provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists the required tools and presents a step-by-step process involving removing bolts, seals, gears, and other components. Safety notices are included to handle fluids properly and avoid injury from hydraulic pressure. The disassembly procedure removes the outer casing pieces and individually dismantles the internal gear and shaft assemblies.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings using various specialized tools. Safety warnings are provided regarding potential hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process.
The document is a service repair manual that provides instructions for disassembling the final drive of a 313D2 LGP excavator. It lists 33 steps to completely disassemble the final drive and related components. The steps include removing mounting bolts, seals, springs, gears, shafts, washers, and housings. Safety notices are provided throughout to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and released spring forces. Tools required for the disassembly are also listed.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids or heavy components during the disassembly process.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process. Tools required are listed in a table.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...f8usiejdkmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...f9oseikkdks
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...jfkskmmdmdm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...jfkskmdmmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove parts such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as released spring forces or hot/pressurized hydraulic oil. The goal is to fully disassemble the final drive to allow inspection and replacement of components.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive from the machine, disassembling internal components like carriers and planetary gears, and separating housings. Safety notices are included to warn of hazards like stored spring energy or hot/pressurized fluids.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It describes:
- Required tools for disassembly
- Removing the final drive assembly and positioning it on a repair stand
- Disassembling the final drive components like the cover, carrier assembly, ring gears, and housing
- Removing planetary gears, shafts, seals and other internal parts
The detailed step-by-step process involves removing over 30 individual parts and components from the final drive assembly. Cleanliness and proper lifting of heavy components are emphasized for safety.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive from the machine, disassembling internal components like carriers and planetary gears, and separating housings. Safety notices are included to release pressures and handle heavy parts. The detailed process is intended to allow thorough disassembly for repair or replacement of parts.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...ze6074xunong
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove components such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces during disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...f8usiejdkmdd
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove parts such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces. Detailed illustrations accompany each step for clarity.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...f9oseikkdks
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It describes:
- Required tools for disassembly
- Removing the final drive assembly and mounting it to a repair stand
- Disassembling the final drive components like the cover, carrier assembly, ring gears, and housing
- Removing planetary gears, shafts, seals and other internal parts
The detailed step-by-step process involves removing over 30 individual parts in the proper sequence. Cleanliness is emphasized and weights of components are provided.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...jfkskmmdmdm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...jfkskmdmmdd
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove components such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces. Detailed illustrations accompany each step for clarity.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
Caterpillar Cat 318D2 L Excavator (Prefix XGS) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar Cat 318D2 L Excavator (Prefix XGS) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly housing various components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Precautions are provided regarding releasing spring forces and containing hydraulic fluids during disassembly.
Clark C500, Y300S Forklift Service Repair Manual.pdff7siejdkdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and not for public distribution. The index covers various systems of the forklift like the engine, transmission, hydraulics, brakes and electrical systems. It provides diagrams and guides technicians through troubleshooting, removing and replacing components, and adjusting various parts of the forklift. Safety warnings and best practices are outlined for technicians to follow when performing maintenance.
Clark C500, Y350 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides a summary of procedures for performing planned maintenance (PM) on Clark lift trucks. It outlines the importance of regular inspections and lubrication for long life and trouble-free operation. It recommends using a PM report form as a checklist to document inspections and needed repairs. Safety precautions are listed, such as disconnecting the battery before working on electrical components. Visual inspections of the truck and its components are described to identify damage, leaks, and worn parts. Specific components discussed include the overhead guard, carriage, upright assembly, lift chains, cylinders, forks, and wheels/tires. Record keeping of inspection results is advised.
More Related Content
Similar to Caterpillar Cat 313D2 LGP Excavator (Prefix RKN) Service Repair Manual (RKN00001 and up).pdf
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for maintenance or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as heavy component weights, pressurized fluids, and released spring forces during the disassembly process. Tools required are listed in a table.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...f8usiejdkmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...f9oseikkdks
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...jfkskmmdmdm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, shafts, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Tools required include lifting devices, stands, pins, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar Cat 318D2 L Excavator (Prefix WGR) Service Repair Manual (WGR0000...jfkskmdmmdd
This document provides instructions for disassembling the final drive on a 318D2 L Excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and other internal parts. Precautions are provided to ensure cleanliness and prevent injury from fluids. The overall process separates the final drive into its individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove parts such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as released spring forces or hot/pressurized hydraulic oil. The goal is to fully disassemble the final drive to allow inspection and replacement of components.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...yu5676962
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive from the machine, disassembling internal components like carriers and planetary gears, and separating housings. Safety notices are included to warn of hazards like stored spring energy or hot/pressurized fluids.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It describes:
- Required tools for disassembly
- Removing the final drive assembly and positioning it on a repair stand
- Disassembling the final drive components like the cover, carrier assembly, ring gears, and housing
- Removing planetary gears, shafts, seals and other internal parts
The detailed step-by-step process involves removing over 30 individual parts and components from the final drive assembly. Cleanliness and proper lifting of heavy components are emphasized for safety.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive from the machine, disassembling internal components like carriers and planetary gears, and separating housings. Safety notices are included to release pressures and handle heavy parts. The detailed process is intended to allow thorough disassembly for repair or replacement of parts.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...ze6074xunong
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove components such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces during disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...f8usiejdkmdd
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove parts such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces. Detailed illustrations accompany each step for clarity.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...f9oseikkdks
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It describes:
- Required tools for disassembly
- Removing the final drive assembly and mounting it to a repair stand
- Disassembling the final drive components like the cover, carrier assembly, ring gears, and housing
- Removing planetary gears, shafts, seals and other internal parts
The detailed step-by-step process involves removing over 30 individual parts in the proper sequence. Cleanliness is emphasized and weights of components are provided.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...jfkskmmdmdm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual (DPJ0000...jfkskmdmmdd
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and gives step-by-step instructions to remove components such as the cover, carrier assembly, ring gears, and seals. Safety notices are included to warn of hazards such as heavy component weights, pressurized hydraulic fluid, and spring forces. Detailed illustrations accompany each step for clarity.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
Caterpillar Cat 318D2 L Excavator (Prefix XGS) Service Repair Manual Instant ...gongfuao7509
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar Cat 318D2 L Excavator (Prefix XGS) Service Repair Manual Instant ...tengtui535
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly housing various components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Precautions are provided regarding releasing spring forces and containing hydraulic fluids during disassembly.
Similar to Caterpillar Cat 313D2 LGP Excavator (Prefix RKN) Service Repair Manual (RKN00001 and up).pdf (20)
Clark C500, Y300S Forklift Service Repair Manual.pdff7siejdkdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and not for public distribution. The index covers various systems of the forklift like the engine, transmission, hydraulics, brakes and electrical systems. It provides diagrams and guides technicians through troubleshooting, removing and replacing components, and adjusting various parts of the forklift. Safety warnings and best practices are outlined for technicians to follow when performing maintenance.
Clark C500, Y350 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides a summary of procedures for performing planned maintenance (PM) on Clark lift trucks. It outlines the importance of regular inspections and lubrication for long life and trouble-free operation. It recommends using a PM report form as a checklist to document inspections and needed repairs. Safety precautions are listed, such as disconnecting the battery before working on electrical components. Visual inspections of the truck and its components are described to identify damage, leaks, and worn parts. Specific components discussed include the overhead guard, carriage, upright assembly, lift chains, cylinders, forks, and wheels/tires. Record keeping of inspection results is advised.
Clark CMP 50S Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CGP 40 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides information about periodic maintenance schedules for Clark lift trucks. It discusses the terms "periodic service" and "planned maintenance" and how they relate to regularly scheduled maintenance tasks. It provides details on determining appropriate maintenance intervals based on operating conditions. The document includes a service chart that indicates basic maintenance tasks and recommended intervals. It also includes a recommended periodic service schedule chart that lists specific maintenance tasks, the suggested time intervals to perform them, and the service manual group where each task is covered.
Clark CMP 40 Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CMP 45 Forklift Service Repair Manual.pdff7siejdkdmd
The document provides safety guidelines for maintaining Clark industrial trucks. It lists 21 safe maintenance practices, such as raising drive wheels before working on the truck, disconnecting the battery, checking for fuel leaks, using qualified personnel, and ensuring proper ventilation. Special precautions are outlined for hazardous areas and modifications to trucks. References to additional safety standards from ANSI, NFPA, and OSHA are also provided.
Clark CGP 70 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides information about periodic maintenance schedules for Clark lift trucks. It discusses the terms "periodic service" and "planned maintenance" and how they relate to regularly scheduled maintenance tasks. It provides details on determining appropriate maintenance intervals based on operating conditions. The document includes a service chart that indicates basic maintenance tasks and recommended intervals. It also includes a recommended periodic service schedule chart that lists specific maintenance tasks, the suggested time intervals to perform them, and the service manual group where each task is covered.
Clark C500, Y300L Forklift Service Repair Manual.pdff7siejdkdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components grouped by system (e.g. engine, transmission, hydraulics). Safety instructions are provided for forklift maintenance personnel.
Clark CGC 40 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides information about periodic maintenance schedules for Clark lift trucks. It discusses the terms "periodic service" and "planned maintenance" and how they relate to regularly scheduled maintenance tasks. It provides details on determining appropriate maintenance intervals based on operating conditions. The document includes a service chart that indicates basic maintenance tasks and recommended intervals. It also includes a recommended periodic service schedule chart that lists specific maintenance tasks, the suggested time intervals to perform them, and the service manual group where each task is covered.
Clark CGC 70 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides information about periodic maintenance schedules for Clark lift trucks. It discusses the terms "periodic service" and "planned maintenance" and how they relate to regularly scheduled maintenance tasks. It provides details on determining appropriate maintenance intervals based on operating conditions. The document includes a service chart that indicates basic maintenance tasks and recommended intervals. It also includes a recommended periodic service schedule chart that lists specific maintenance tasks, the suggested time intervals to perform them, and the service manual group where each task is covered.
Clark C500, Y250S Forklift Service Repair Manual.pdff7siejdkdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and not for public distribution. The index covers various systems of the forklift like the engine, transmission, hydraulics, brakes and electrical systems. It provides diagrams and guides technicians through troubleshooting, removing and replacing components, and adjusting various parts of the forklift. Safety warnings and best practices are outlined for technicians to follow when performing maintenance.
Clark C500, Y225L Forklift Service Repair Manual.pdff7siejdkdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components grouped into sections for topics like engines, transmissions, hydraulics, brakes, and specifications. Safety instructions are provided for maintenance personnel.
Clark C500, Y250L Forklift Service Repair Manual.pdff7siejdkdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material and distribution restrictions are noted. Safety practices for maintenance personnel are outlined.
Clark C500, Y200 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides instructions and guidelines for performing planned maintenance (PM) on Clark lift trucks. It outlines the importance of regular inspections and recommends using a PM report form to document the inspections. Safety precautions are described, such as disconnecting the battery before working on electrical components. A visual inspection process is outlined to check for issues like leaks, loose or damaged parts, and worn components. Inspections of specific systems like the uprights, forks, and hydraulic lines are detailed. Record-keeping of inspection results is advised to monitor truck condition and maintenance needs.
Clark C500, Y225S Forklift Service Repair Manual.pdff7siejdkdmd
This document provides instructions and maintenance procedures for Clark lift trucks. It begins with introductory information on safety signs, user safe maintenance practices, and how to perform periodic maintenance using the provided report form. The bulk of the document consists of an index that lists maintenance groups and sections to inspect things like the engine, transmission, hydraulic components, brakes, steering and other systems. Safety is emphasized throughout and the reader is advised to follow all procedures and recommendations to properly maintain the trucks.
Clark C500, Y180 Forklift Service Repair Manual.pdff7siejdkdmd
This document provides a summary of procedures for performing planned maintenance (PM) on Clark lift trucks. It outlines the importance of regular inspections and lubrication for long life and trouble-free operation. It recommends using a PM report form as a checklist to document inspections and any needed repairs. Safety precautions are listed, such as disconnecting the battery before working on electrical components. Visual inspections of the truck and its components are described to identify any damage, leaks, or loose fittings. Specific components discussed include the overhead guard, carriage, upright assembly, lift chains, cylinders, forks, and wheels/tires.
Caterpillar Cat 336F L Excavator (Prefix TZA) Service Repair Manual (TZA00001...f7siejdkdmd
This document provides instructions for disassembling the travel motor on a 336F L excavator. The 27 step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate and springs. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Clark C15-32C LG Forklift Service Repair Manual.pdff7siejdkdmd
This document provides instructions and guidelines for safely maintaining a Clark lift truck. It discusses maintaining the truck according to the manufacturer's recommendations and using only trained personnel. When working on the truck, proper safety procedures should be followed such as raising the wheels, disconnecting the battery, and ensuring fuel systems are shut off. The document emphasizes inspecting all vehicle functions and components regularly to ensure safe operation. Modifications require manufacturer approval. Replacement parts must be of equal or better quality than original equipment.
Caterpillar Cat C7 Marine Engine Parts Catalogue Manual.pdff7siejdkdmd
This document is a parts manual for Caterpillar C7 marine engines. It contains a table of contents that lists components and systems of the engine, including the basic engine, lubrication system, cooling system, air inlet and exhaust system, fuel system, electrical and starting system, and operator station. The parts manual is available in PDF format on a compact disc.
Caterpillar Cat 336F L Excavator (Prefix RKB) Service Repair Manual (RKB00001...f7siejdkdmd
This document provides instructions for disassembling the travel motor on a 336F L excavator. It describes 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and port plate. Tools required include a transmission repair stand, lifting eye assembly, driver group, retaining ring pliers and bearing puller group. Safety precautions are provided to release spring forces and contain fluids during disassembly.
I am an accomplished and driven administrative management professional with a proven track record of supporting senior executives and managing administrative teams. I am skilled in strategic planning, project management, and organizational development, and have extensive experience in improving processes, enhancing productivity, and implementing solutions to support business objectives and growth.
Delta International is an ISO Certified top recruiting agency in Pakistan, recognized for its highly experienced recruiters. With a diverse range of international jobs for Pakistani workers, Delta International maintains extensive connections with overseas employers, making it one of the top 10 recruitment agencies in Pakistan. It stands out in the list of recruitment agencies in Pakistan for its exceptional services.
https://www.ditrc.com/
Known for its expertise in the Gulf region, Delta International is among the top 10 international recruitment agencies, specializing in expert headhunting and candidate sourcing. This prominence places it in the list of top 10 overseas recruitment agencies in Pakistan. As one of the best overseas recruitment agencies in Pakistan, Delta International is a trusted name for manpower recruitment, particularly from Pakistan.
The agency is not just a leading name in Karachi but also recognized as one of the best recruitment agencies in Islamabad. Delta International consistently ranks as the top recruitment agency in Pakistan, earning its reputation among the top recruiting agencies in Pakistan. It is also regarded as one of the top overseas employment agencies in Pakistan.
For those seeking foreign jobs, Delta International is listed among the top overseas employment companies in Pakistan. Their extensive network and expertise make them a go-to for anyone looking at the list of overseas employment agencies in Pakistan. As a leading foreign jobs recruitment agency in Pakistan, they offer opportunities across various sectors.
Delta International is consistently listed among the top recruitment companies in Pakistan, known for providing the best recruitment services. It’s considered one of the best recruitment agencies in Pakistan and a prominent recruitment agency in Pakistan. The company excels in international recruitment, making it a key player among international recruitment agencies in Pakistan.
Their inclusion in the list of international recruitment agencies further attests to their excellence. As a top manpower agency in Pakistan, Delta International specializes in recruiting skilled professionals and labor for various industries, including construction, healthcare, IT, engineering, and hospitality.
Delta International is a leader among recruitment agencies in Pakistan, with a particular focus on overseas employment. They are one of the foremost overseas employment agencies in Pakistan, catering to technical jobs and other employment opportunities. Their role as overseas employment promoters highlights their commitment to connecting Pakistani talent with global opportunities.
In summary, Delta International is not only one of the best recruitment agencies in Pakistan but also a distinguished name among overseas employment agencies. Their extensive network and experienced recruiters make them a top choice for anyone seeking employment both locally and internationally.
Parabolic antenna alignment system with Real-Time Angle Position FeedbackStevenPatrick17
Introduction
Parabolic antennas are a crucial component in many communication systems, including satellite communications, radio telescopes, and television broadcasting. Ensuring these antennas are properly aligned is vital for optimal performance and signal strength. A parabolic antenna alignment system, equipped with real-time angle position feedback and fault tracking, is designed to address this need. This document delves into the components, design, and implementation of such a system, highlighting its significance and applications.
Importance of Parabolic Antenna Alignment
The alignment of a parabolic antenna directly affects its performance. Even minor misalignments can lead to significant signal loss, which can degrade the quality of the received signal or cause communication failures. Proper alignment ensures that the antenna's focal point is accurately directed toward the signal source, maximizing the antenna's gain and efficiency. This precision is especially crucial in applications like satellite communications, where the antenna must track geostationary satellites with high accuracy.
Components of a Parabolic Antenna Alignment System
A parabolic antenna alignment system typically includes the following components:
Parabolic Dish: The primary reflector that collects and focuses incoming signals.
Feedhorn and Low Noise Block (LNB): Positioned at the dish's focal point to receive signals.
Stepper or Servo Motors: Adjust the azimuth (horizontal) and elevation (vertical) angles of the antenna.
Microcontroller (e.g., Arduino, Raspberry Pi): Processes sensor data and controls the motors.
Potentiometers: Provide feedback on the antenna's current angle positions.
Fault Detection Sensors: Monitor for potential faults such as cable discontinuities or LNB failures.
Control Software: Runs on the microcontroller, handling real-time processing and decision-making.
Real-Time Angle Position Feedback
Real-time feedback on the antenna's angle position is essential for maintaining precise alignment. This feedback is typically provided by potentiometers or rotary encoders, which continuously monitor the azimuth and elevation angles. The microcontroller reads this data and adjusts the motors accordingly to keep the antenna aligned with the signal source.
Fault Tracking in Antenna Alignment Systems
Fault tracking is vital for the reliability and performance of the antenna system. Common faults include cable discontinuities, LNB malfunctions, and motor failures. Sensors integrated into the system can detect these faults and either notify the user or initiate corrective actions automatically.
Design and Implementation
1. Parabolic Dish and Feedhorn
The parabolic dish is designed to reflect incoming signals to a focal point where the feedhorn and LNB are located. The dish's size and shape depend on the specific application and frequency range.
2. Motors and Position Control
Stepper motors or servo motors are used to control the azimuth and elevation of
We recently hosted the much-anticipated Community Skill Builders Workshop during our June online meeting. This event was a culmination of six months of listening to your feedback and crafting solutions to better support your PMI journey. Here’s a look back at what happened and the exciting developments that emerged from our collaborative efforts.
A Gathering of Minds
We were thrilled to see a diverse group of attendees, including local certified PMI trainers and both new and experienced members eager to contribute their perspectives. The workshop was structured into three dynamic discussion sessions, each led by our dedicated membership advocates.
Key Takeaways and Future Directions
The insights and feedback gathered from these discussions were invaluable. Here are some of the key takeaways and the steps we are taking to address them:
• Enhanced Resource Accessibility: We are working on a new, user-friendly resource page that will make it easier for members to access training materials and real-world application guides.
• Structured Mentorship Program: Plans are underway to launch a mentorship program that will connect members with experienced professionals for guidance and support.
• Increased Networking Opportunities: Expect to see more frequent and varied networking events, both virtual and in-person, to help you build connections and foster a sense of community.
Moving Forward
We are committed to turning your feedback into actionable solutions that enhance your PMI journey. This workshop was just the beginning. By actively participating and sharing your experiences, you have helped shape the future of our Chapter’s offerings.
Thank you to everyone who attended and contributed to the success of the Community Skill Builders Workshop. Your engagement and enthusiasm are what make our Chapter strong and vibrant. Stay tuned for updates on the new initiatives and opportunities to get involved. Together, we are building a community that supports and empowers each other on our PMI journeys.
Stay connected, stay engaged, and let’s continue to grow together!
About PMI Silver Spring Chapter
We are a branch of the Project Management Institute. We offer a platform for project management professionals in Silver Spring, MD, and the DC/Baltimore metro area. Monthly meetings facilitate networking, knowledge sharing, and professional development. For more, visit pmissc.org.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 LGP EXCAVATOR RKN
Configuration: 313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR3323-06 Publication Date -01/06/2018 Date Updated -27/06/2018
i05453130
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
1/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate two ring gears (17).
Note: Two ring gears (17) are held together with Tooling (F). It may be necessary to heat
ring gears (17) in order to soften the sealant. Do not heat over 135 °C (275 °F) for more
than thirty minutes.
6/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from main housing (18) once gear (26) is removed.
Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from motor housing (28). The combined weight of main housing (18) and the final
drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 15:59:24 UTC+0800 2020
11/11
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 LGP EXCAVATOR RKN
Configuration: 313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR3323-06 Publication Date -01/06/2018 Date Updated -27/06/2018
i07255515
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 477-3191 M14x2x18 mm Lifting Eye Assembly 2
B 1P-2420 Transmission Repair Stand 1
C
6V-8214 M6x20mm Bolt 2
9X-8267 M6 Washer 2
D 8H-0663 Bearing Puller Assembly 1
E 422-5474 M16x2x24mm Lifting Eye Assembly 2
F 439-3938 Link Bracket 3
G 1U-9889 Crossblock 1
Start By:
a. Remove the final drive and the travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor assembly. The weight of the
sprocket is approximately 36 kg (79 lb).
Illustration 1 g06260984
3. Use Tooling (A) and a suitable lifting device to position final drive assembly (1) onto
Tooling (B). The weight of final drive assembly (1) is approximately 281 kg (620 lb).
2/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06261012
Illustration 3 g06261017
4. Remove plug (2), spring (4), seat (3), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
3/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 4 g06261029
Illustration 5 g06261032
5. Remove plug (5), spring (6), seat (7), stem assembly (8), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g06261260
Illustration 7 g06261275
6. Remove plug (9), spring (12), seat (11), spool (10), and the O-ring seal.
Illustration 8 g06261285
7. Remove adapter (13) and the O-ring seal.
5/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 9 g06261336
Illustration 10 g06261344
8. Remove plug (14), spring (16), valve (15), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
6/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g06261519
Illustration 12 g06261532
9. Remove plug (17), spring (19), valve (18), and the O-ring seal.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g06261538
Illustration 14 g06261539
10. Remove plugs (20) and the O-ring seals.
11. Remove plugs (21), springs (23), valves (22), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 15 g06261563
12. Remove bolts (24) and valve body (25).
Illustration 16 g06263306
Port plate (28) may still be adhered to the barrel assembly.
13. Remove springs (26), port plate (28), and O-ring seals (27).
Illustration 17 g06261586
14. Remove bearing (29).
15. Remove O-ring seal (30).
9/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine(S...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g06261622
16. Use Tooling (C) and suitable prying devices to remove piston assembly (31).
Illustration 19 g06261625
17. Remove O-ring seal (32) and O-ring seal (33).
Illustration 20 g06261647
10/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 21 g06261665
18. Remove separator plates (34) and friction plates (35). Note the alternating order of separator
plates (34) and friction plates (35) for assembly purposes.
Illustration 22 g06261896
19. Remove barrel assembly (36). Do not allow the components of barrel assembly (36) to
come apart while you remove barrel assembly (36). The components of barrel assembly (36)
must be reinstalled in the original positions.
Illustration 23 g06261908
20. Remove piston assemblies (37) and retainer (38).
11/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 24 g06261915
21. Remove guide (39).
Illustration 25 g06261922
22. Remove springs (40).
12/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 26 g06261927
23. Put location marks on swashplate (41) for assembly purposes. Remove swashplate (41).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 27 g06261980
13/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 28 g06261983
24. Remove shaft assembly (42), keys (44), piston (43), and spring (45).
Illustration 29 g06261987
25. Use a suitable press and Tooling (D) to remove bearing (46) off the shaft assembly.
Illustration 30 g06262009
14/22
313D2 LGP Excavator RKN00001-UP (MACHINE) POWERED BY 3054C Engine...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...