This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
1) Using valve spring compressors and other tools to remove the valve springs, valve spring retainers, and valves.
2) Inspecting the removed parts and checking the valve springs.
3) Lubricating and installing the valves, valve springs, retainers, and securing the springs with the compressor.
4) The document cautions that parts under spring force can injure technicians and specifies wearing protective equipment.
This document provides instructions for removing inlet and exhaust valve seat inserts from the cylinder head of a C27 Industrial Engine. Key points include:
- Use a valve seat cutter and reamer to remove the existing valve seat insert.
- Inspect the cylinder head bore for any damage or wear after removal of the insert.
- Thoroughly clean the cylinder head bore before installing a new valve seat insert.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Valves, springs, and related parts. Tools are needed to compress springs safely.
2) Valve guides. Guides must be installed to the correct height specification.
3) Valve seat inserts. New inserts must be cooled before installation.
4) The oil filter base. Springs under covers require care during removal.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, valve guides, and valve seat inserts.
2) The engine oil filter base, oil cooler, and engine oil pump.
3) Safety precautions and required tools are listed for each procedure. Detailed illustrations and step-by-step instructions are provided.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
This document provides instructions for removing inlet and exhaust valve seat inserts from the cylinder head of a C27 Industrial Engine. Key points include:
- Use a valve seat cutter and reamer to remove the existing valve seat insert.
- Inspect the cylinder head bore for any damage or wear after removal of the insert.
- Thoroughly clean the cylinder head bore before installing a new valve seat insert.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Valves, springs, and related parts. Tools are needed to compress springs safely.
2) Valve guides. Guides must be installed to the correct height specification.
3) Valve seat inserts. New inserts must be cooled before installation.
4) The oil filter base. Springs under covers require care during removal.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, valve guides, and valve seat inserts.
2) The engine oil filter base, oil cooler, and engine oil pump.
3) Safety precautions and required tools are listed for each procedure. Detailed illustrations and step-by-step instructions are provided.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
The document provides instructions for removing and installing inlet and exhaust valve springs on a C27 Industrial Engine.
It describes the required tools and gives a step-by-step process for removing the valve springs which includes using a valve spring compressor tool to compress the springs so the spring keepers can be removed from the valve. It then provides instructions for installing new valve springs which involves lubricating the valves, compressing the springs with the tool to insert the spring keepers.
The document also provides procedures for removing and installing inlet and exhaust valve guides from the cylinder head using driver tools to remove and install the guides at the proper height. Lubrication and sealing of the guides is described.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure to remove the engine oil filter base, oil cooler, and draining coolant, requiring draining fluids and disconnecting hoses.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for further maintenance. Safety notices are provided regarding containment of fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, guides, and seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2) The engine oil filter base, oil cooler, and oil pump. It instructs to drain fluids, then remove mounting bolts and connectors to take parts off.
3) Safety precautions are emphasized such as keeping parts clean, containing fluids, and wearing protective equipment when working with spring-loaded parts.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
Massey ferguson mf 164 t v tractor parts catalogue manualeudskkejedmm
This document provides a parts list and technical specifications for the Massey Ferguson MF 164 TV tractor engine. It includes over 60 items with descriptions and part numbers for the cylinder block, crankshaft, flywheel, cylinder head, camshaft, timing gears, rocker arm, and lubricating oil system. The list is highly detailed and specific to help identify replacement parts for the MF 164 TV tractor engine.
Massey ferguson mf 154 v tractor parts catalogue manualeudskkejedmm
This document provides a parts list for a Massey Ferguson MF 154 V tractor. It contains over 60 items with part numbers, quantities, descriptions, and other details. The list is organized by component systems including the cylinder block, crankshaft, cylinder head, rocker arm, timing gear, and lubricating oil system.
More Related Content
Similar to Caterpillar cat c27 industrial engine (prefix jfj) service repair manual (jfj00001 and up)
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
- Inlet and exhaust valve springs
- Inlet and exhaust valves
- Inlet and exhaust valve guides
- Inlet and exhaust valve seat inserts
- Engine oil filter base
The procedures describe the required tools, removal steps, inspection, installation steps, and safety precautions for each component. Detailed illustrations supplement the text instructions.
The document provides instructions for removing and installing inlet and exhaust valve springs on a C27 Industrial Engine.
It describes the required tools and gives a step-by-step process for removing the valve springs which includes using a valve spring compressor tool to compress the springs so the spring keepers can be removed from the valve. It then provides instructions for installing new valve springs which involves lubricating the valves, compressing the springs with the tool to insert the spring keepers.
The document also provides procedures for removing and installing inlet and exhaust valve guides from the cylinder head using driver tools to remove and install the guides at the proper height. Lubrication and sealing of the guides is described.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure to remove the engine oil filter base, oil cooler, and draining coolant, requiring draining fluids and disconnecting hoses.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for further maintenance. Safety notices are provided regarding containment of fluids.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Inlet and exhaust valves, guides, and seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2) The engine oil filter base, oil cooler, and oil pump. It instructs to drain fluids, then remove mounting bolts and connectors to take parts off.
3) Safety precautions are emphasized such as keeping parts clean, containing fluids, and wearing protective equipment when working with spring-loaded parts.
The document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1) Removal and installation procedures for inlet and exhaust valves, requiring the use of valve spring compressors and ensuring parts are kept clean.
2) Removal and installation of valve guides using driver tools and maintaining proper protrusion distances.
3) Removal and installation of valve seat inserts using pullers and drivers, keeping inserts clean.
4) Procedure for removing the engine oil filter base, oil cooler, and draining coolant in preparation for maintenance.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
Similar to Caterpillar cat c27 industrial engine (prefix jfj) service repair manual (jfj00001 and up) (20)
Massey ferguson mf 164 t v tractor parts catalogue manualeudskkejedmm
This document provides a parts list and technical specifications for the Massey Ferguson MF 164 TV tractor engine. It includes over 60 items with descriptions and part numbers for the cylinder block, crankshaft, flywheel, cylinder head, camshaft, timing gears, rocker arm, and lubricating oil system. The list is highly detailed and specific to help identify replacement parts for the MF 164 TV tractor engine.
Massey ferguson mf 154 v tractor parts catalogue manualeudskkejedmm
This document provides a parts list for a Massey Ferguson MF 154 V tractor. It contains over 60 items with part numbers, quantities, descriptions, and other details. The list is organized by component systems including the cylinder block, crankshaft, cylinder head, rocker arm, timing gear, and lubricating oil system.
Massey ferguson mf 154 s tractor parts catalogue manualeudskkejedmm
This document provides a parts list for a Massey Ferguson MF 154 S tractor, including the cylinder block, crankshaft and flywheel, cylinder head and cover, rocker arm, timing gear, and lubricating oil system components. It lists 73 parts with descriptions and part numbers. The list is organized by component and includes additional details like serial number ranges for some parts.
Massey ferguson mf 154 f tractor parts catalogue manualeudskkejedmm
This document contains parts lists and descriptions for components of a Massey Ferguson 154 F tractor, including the cylinder block, crankshaft and flywheel, cylinder head and cover, rocker arm, and timing gear. It lists 75 individual parts with descriptions and part numbers. The summary provides an overview of the components covered without reproducing the entire detailed parts listing.
Massey ferguson mf 134 v tractor parts catalogue manualeudskkejedmm
This document provides a parts list and descriptions for a Massey Ferguson 134 V tractor engine. It includes 3 pages listing 74 individual parts related to the cylinder block, such as the cylinder block itself, bolts, plugs, liners and gaskets. It also lists parts for the crankshaft, flywheel, cylinder head, cover, rocker arm, and timing gear. Each part is identified by number, part number, quantity and description, along with any relevant comments.
Massey ferguson mf 20 combine parts catalogue manualeudskkejedmm
This document contains parts information for a Massey Ferguson MF 20 combine engine. It includes lists of parts for the cylinder block, crankshaft, pistons, connecting rods, and cylinder head. Each part is accompanied by part numbers, quantities, descriptions, and additional comments to specify application or replacement information. The document provides detailed reference information for servicing and repairing parts of the MF 20 combine engine.
Massey ferguson mf 16 16 plot combine parts catalogue manualeudskkejedmm
This document contains parts lists and diagrams for a Massey Ferguson MF 16/16 plot combine. It includes detailed lists of parts for various systems of the combine like the cylinder block, crankshaft, cylinder head, timing gears, and fuel injection equipment. Each item is accompanied by information like part number, quantity, description, and any relevant comments. Diagrams visually show the layout and components within each system.
Massey ferguson mf 10 combine, plot parts catalogue manualeudskkejedmm
This document provides part numbers and descriptions for components of a Massey Ferguson MF 10 combine. It includes sections for the cylinder block, crankshaft, cylinder head, cylinder head cover, timing gear, lubricating oil pump, and fuel injection equipment. Each section lists the relevant part numbers, quantities, and short descriptions for each component item. Additional information may be provided such as replacement part numbers or thickness specifications.
Kubota b7500 d tractor parts catalogue manualeudskkejedmm
This parts book page provides information on crankcase parts for a tractor model B7500D. It lists 20 individual crankcase parts with reference numbers, part numbers, descriptions, quantities used, serial number ranges for interchangeability, and remarks. Key information includes the composite crankcase part numbers for different serial number ranges and individual weights for each crankcase part listed.
Kubota b7410 d tractor parts catalogue manualeudskkejedmm
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including the reference number, part number, description, quantity, serial number range, interchangeability, and remarks. It also notes country codes that may be included and their meanings. The document then provides an example page from the parts book that lists specific part numbers, descriptions, quantities, and other details for a tractor engine and oil pan.
Kubota b7400 hsd tractor parts catalogue manualeudskkejedmm
The document provides instructions for parts books, including definitions of column headings in parts number pages. It lists country codes that may be included for parts that differ between countries. It then provides an index and sample pages from a parts book for a B7400HSD tractor, including lists of parts with part numbers, descriptions, quantities, serial number ranges and other details.
Kubota b7300 hsd tractor parts catalogue manualeudskkejedmm
The document provides instructions for using a parts book. It defines column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and what they represent. An example page from the parts book is then shown listing parts for a B7300HSD engine with reference number, part number, description, quantity, serial number range and remarks.
Kubota b7200 hstd tractor parts catalogue manualeudskkejedmm
This document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages, including the reference number, part number, description, quantity, serial number range and interchangeability. Country codes are also explained, noting that parts may differ by country. An example page from the parts book is then shown, listing part numbers, descriptions and other details for engine crankcase parts.
Kubota b7200 e tractor parts catalogue manualeudskkejedmm
This document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they indicate for part differences between countries.
Kubota b7200 d tractor parts catalogue manualeudskkejedmm
This document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture page. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes may be included and provides examples. Finally, it lists an index of parts for a B7200D tractor organized by system.
Kubota b6200 d tractor parts catalogue manualeudskkejedmm
The document provides instructions for using a parts book. It defines column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. An example page from the parts book is then shown listing parts by reference number, part number, description, quantity and the book they can be found in.
Komatsu pc250 lc 6 hydraulic excavator service repair manual (a83000 and up)eudskkejedmm
This document provides information about service manuals and publications for Komatsu hydraulic excavators models PC200LC-6, PC210LC-6, PC220LC-6, and PC250LC-6. It lists the available publications, including parts books, operation and maintenance manuals, and shop manuals. It explains that these publications can only be acquired through authorized Komatsu distributors using the Parts Information Processing System. It also provides a form that can be used to request publications if the PIPS system is unavailable. The document emphasizes safety precautions that should be followed when performing any service or repairs.
Komatsu pc250 lc 6 hydraulic excavator service repair manual (a82001 and up)eudskkejedmm
This shop manual provides technical information for servicing a hydraulic excavator. It is divided into sections covering general specifications, structure and function of components, testing and adjustment procedures, disassembly and assembly instructions, and maintenance standards for inspecting parts. The section on disassembly and assembly of the radiator and hydraulic oil cooler provides instructions for removing and installing the assembly, including disconnecting hoses and support rods, removing mounting bolts, lifting the assembly off, and refilling fluids after installation. Safety precautions are marked throughout.
Komatsu pc220 lc 6 hydraulic excavator service repair manual (a83000 and up)eudskkejedmm
This document provides information about service manuals and publications for Komatsu hydraulic excavators models PC200LC-6, PC210LC-6, PC220LC-6, and PC250LC-6. It lists the available publications, including parts books, operation and maintenance manuals, and shop manuals. It explains that these publications can only be acquired through authorized Komatsu distributors using the Parts Information Processing System. It also provides a form that can be used to request publications if the processing system is unavailable. The document emphasizes safety precautions that should be followed when performing service and repair work.
Komatsu pc27 r 8, pc27r-8 (deluxe) hydraulic excavator service repair manualeudskkejedmm
The document provides instructions on maintenance procedures for heavy machinery. It begins with general safety precautions for working on machinery and preparing for repairs. The document then outlines the structure and sections of the maintenance manual, including chapters on structure and function, testing and adjusting, removal and installation, and maintenance standards. Symbols used in the manual are explained to highlight important safety information.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i06750397
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7241 Valve Spring Compressor 1
B 441-0714 Tool As 1
Start By:
a. Remove the electronic unit injectors.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Place the piston at the top of the compression stroke (TC). Remove the valve springs for
that cylinder. If the valves fall into the cylinder liner, then the cylinder head must be removed.
1. Position the No. 1 piston at the top center of the compression stroke. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
1/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01073852
Illustration 2 g01043625
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 2. Install Tooling (A) in the electronic unit injector sleeve. Secure Tooling (A) with unit
injector clamp (1).
3. Tighten the full nut until valve spring keepers (3) are loose on valve (2).
4. Remove valve spring keepers (3) from the valve.
5. Carefully remove Tooling (A).
6. Remove valve rotator (4).
7. Remove outer valve spring (6) and inner valve spring (5) from the valve.
8. Remove washer (7) from the valve guide.
9. Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, "Cylinder
Head Valves" for additional information on the valve springs.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-7241 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the valve stems with clean engine oil.
3/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g01043625
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Ensure that washer (7) is installed on the valve guide.
3. Install inner valve spring (5) and outer valve spring (6) on valve (2).
4. Install valve rotator (4) on valve (2).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
5. Use Tooling (A) to compress inner valve spring (5) and outer valve spring (6). Install valve
spring keepers (3) on valve (2). Remove unit injector clamp (1) and Tooling (A).
4/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. End By:
a. Install the electronic unit injectors.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:48:14 UTC+0800 2020
5/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i06750410
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 441-0714 Tool As 1
Start By:
a. Remove the cylinder head.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g01015263
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Install Tooling (A) and compress the valve springs. Remove valve spring keepers (2) from
valve (1).
2/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 2. Carefully remove Tooling (A) from valve (1).
3. Remove valve rotator (3).
4. Remove outer valve spring (5) and inner valve spring (4) from valve (1).
5. Remove washer (6) and valve (1) from the valve guide.
6. Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, "Cylinder
Head Valves" for additional information on the valve springs.
7. Inspect the valves. Refer to Specifications, "Cylinder Head Valves" for additional
information on the inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: A small amount of grease can be used to hold the retainer locks in position during
installation.
1. Lubricate the valves with clean engine oil. Install the valves in the cylinder head.
3/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g01015263
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install washer (6) on the valve guide.
3. Install inner valve spring (4) and outer valve spring (5) on valve (1).
4. Install valve rotator (3) on valve (1).
4/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 5. Use Tooling (A) to compress inner valve spring (4) and outer valve spring (5). Install valve
spring keepers (2) on valve (1).
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
6. Carefully remove Tooling (A).
End By:
a. Install the cylinder head.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:49:10 UTC+0800 2020
5/5(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i05887270
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6895 Valve Guide Driver 1
(1)
Part of 9U-7530 Engine Tool Group
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g01073841
1. Remove valve stem seal (1) from valve guide (2).
2. Use Tooling (A) and a hammer to remove the valve guide from the cylinder head.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6895 Valve Guide Driver 1
B(1)
9U-6894 Guide Collar 1
C(2)
455-0128 Seal Installer 1
375-2773 Seal Installer 1
(1)
Part of 9U-7530 Engine Tool Group
(2)
Use Seal Installer 455-0128 with Seal 163-2478. Use Seal Installer 375-2773 with Seal 361-3926
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 2 g01073842
1. Lubricate the bores for the valve guides with clean engine oil.
2. Install valve guide (2) in the cylinder head with Tooling (A) and Tooling (B).
Note: Tooling (B) must be used in order to install the valve guide to the correct height.
Height to top of valve guide from cylinder head surface ... 35.00 ± 0.50 mm
(1.378 ± 0.020 inch)
Note: For more information, refer to Specifications, "Cylinder Head Valves".
3. Use Tooling (C) to install valve stem seal (1) on the valve guide.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:50:05 UTC+0800 2020
3/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i04947937
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 166-7441 Valve Seat Extractor Tool Group 1
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g01145463
1. Use Tooling (A) to remove valve seat insert (1) from the cylinder head.
2. Clean the bores in the cylinder head for the valve seat inserts. Remove any rough areas from
the bores.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B(1)
9U-6898 Valve Seat Driver (Exhaust) 1
9U-6897 Valve Seat Driver (Inlet) 1
(1)
Part of 9U-7530 Engine Tool Group
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g01079028
1. Lower the temperature of new valve seat insert (1).
2. Use Tooling (B) to install the new valve seat insert in the cylinder head.
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:51:01 UTC+0800 2020
3/3(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i04085349
Engine Oil Filter Base - Remove and Install
SMCS - 1306-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Illustration 1 g02294113
1. Use Tooling (A) to remove engine oil filters (4).
2. Remove bracket (3)
3. Remove bolts (1) and remove the engine oil filter base (2).
1/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g02294238
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
4. Remove cover (5), gasket (6), springs (7) and plungers (8) from oil filter base (2).
Installation Procedure
1. Install the engine oil filter base (2) in the reverse order.
a. Apply clean engine oil to the oil filter seals prior to installation. Install the engine oil
filters until the oil filter seal contacts the base, then turn the engine oil filters one full
turn.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:51:57 UTC+0800 2020
2/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i04158087
Engine Oil Cooler - Remove and Install
SMCS - 1378-010
Removal Procedure
Start By:
a. Remove the exhaust cooler (NRS).
b. Remove the engine oil filter base.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g02352422
Note: Ensure that engine oil cooler core (1) does not fall when bonnet (2) is removed.
2. Remove bolts (3), bonnet (2), and the gasket.
Illustration 2 g02352423
3. Slide engine oil cooler core (1) and bypass tube assembly (4) toward the front of the engine
and remove engine oil cooler core (1) and bypass tube assembly (4).
4. If necessary, remove bolts (5), bonnet (6), and the gasket.
Installation Procedure
1. Install engine oil cooler core (1) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:52:53 UTC+0800 2020
2/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i02288785
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Disconnect the tube assemblies from the engine oil pump.
1/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 1 g01145746
2. Remove bolts (1) and engine oil pump (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 13 22:53:48 UTC+0800 2020
2/2(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE JFJ
Configuration: C27 Industrial Engine JFJ00001-UP
Disassembly and Assembly
C27 and C32 Engines
Media Number -M0074364-00 Publication Date -01/08/2015 Date Updated -13/09/2016
i02289189
Engine Oil Pump - Disassemble
SMCS - 1304-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-2320 Puller Assembly 1
Start By:
a. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 1 g01145905
1. Remove bolt (5), thrust plate (6), and idler gear assembly (7) from shaft assembly (8).
2. Use Tooling (A) and a suitable press in order to remove the bearing from idler gear
assembly (7).
3. Remove shaft assembly (8) from body (4). Remove bolt (1) and washer (2).
4. Use Tooling (A) and Tooling (B) to remove drive gear (3) from body (4). Remove the key
from the pump shaft.
2/4(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 2 g01145925
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove bolts (9) and separate body (10) from spacer (12) and body (4).
6. Use Tooling (A) and a suitable press in order to remove the bearings from body (10).
7. Remove gears (11). Remove spacer (12).
8. Remove the bearings from spacer (12).
9. Remove shaft assemblies (13).
10. Remove bolts (14) and retainer (15).
3/4(W)
w
2020/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...