KUBOTA B2410DB TRACTOR Service Repair Manual.pdf

B1710,B2110,B2410,B2710
WORKSHOP MANUAL
TRACTOR
KiSC issued 11, 2006 A

7
B1710 · B2110 · B2410 · B2710, WSM SPECIFICATIONS
SPECIFICATIONS
Note : * Manufacture’s estimate
The company reserves the right to change the specifications without notice.
W10281170
Model B1710D B2110D B2110DB B2110HDB
PTO power 10.5 kW (14.3 PS)* 12.7 kW (17.3 PS)* 12.0 kW (16.3 PS)*
Engine
Maker KUBOTA
Model D905-D18 D1005-D18
Type Indirect Injection. Vertical, water-cooled, 4-cycle diesel
Number of cylinder 3
Bore and stroke
72 × 73.6 mm
(2.83 × 2.90 in.) 76 × 73.6 mm (2.99 × 2.90 in.).
Total displacement 898 cm3
(54.8 cu.in.) 1001 cm3
(61.1 cu.in.)
Engine power (ECE-R24) 12.1 kW (16.5 PS) 14.0 kW (19.0 PS)
Engine power
(SAE gross)
13.4 kW (18.0 HP) 15.7 kW (21.0 HP)
Rated revolution 43.3 r/s (2600 rpm)
Maximum torque 51 N·m (37.6 ft-lbs) 59 N·m (43.5 ft-lbs)
Battery 12 V, RC : 79 min, CCA : 433 A
Starting system Electric starting with cell starter 12 V, 1.4 kW
Lubricating system Forced lubrication by trochoidal pump
Cooling system Pressurized radiator, forced circulation with water pump
Fuel Diesel fuel No. 2-D [above −10 °C (14 °F)], Diesel fuel No. 1 [below −10 °C (14 °F]
Capacities
Fuel tank 24 L (6.3 U.S.gals., 5.3 Imp.gals.)
Engine crankcase
(with filter)
3.0 L (3.2 U.S.qts., 2.6 Imp.qts.)
Engine coolant 3.8 L (4.0 U.S.qts., 3.3 Imp.qts.)
Transmission case 11.5 L (3.04 U.S.gals., 2.53 Imp.gals.) 12.5 L (3.30 U.S.gals.,
2.75 Imp.gals.)
Front axle case 3.7 L (3.9 U.S.qts., 3.3 Imp.qts.) 4.5 L (4.8 U.S.qts., 4.0 Imp.qts.)
Tires
Front 6-12B 6-12
Rear 8-16 9.5-16
Dimensions
Overall length (with 3P) 2378 mm (93.6 in.) 2405 mm (94.7 in.)
Overall width (min. tread) 990 mm (39.0 in.) 1040 mm (40.9 in.)
Overall height
(with ROPS)
2246 mm (88.4 in.) 2268 mm (89.3 in.)
Overall height
(top of steering wheel) 1283 mm (50.5 in.) 1305 mm (51.4 in.)
Wheel base 1500 mm (59.0 in.)
Minimum ground
clearance 263 mm (10.4 in.) 285 mm (11.2 in.)
Tread
Front 830 mm (32.7 in.)
Rear 740 to 910 mm
(29.1 to 35.8 in.)
795 to 1015 mm (31.3 to 40.0 in.)
Weight (with ROPS) 658 kg (1451 lbs) 668 kg (1473 lbs) 678 kg (1495 lbs) 694 kg (1530 lbs)
Minimum turning
radius
4WD with brake 2.1 m (6.9 feet)
Bi-speed turn
without brake
– 2.1 m (6.9 feet)
Clutch Dry single plate
Travelling
system
Steering Integral type power steering
Transmission Gear shift, 6 forward and 2 reverse
HST with 2 speeds
range gear shift
Brake Wet disk type
Differential Bevel gears
Hydraulic
system
Hydraulic control system Position control
Pump capacity
3P : 16.6 L/min. (4.4 U.S.gals./min., 3.7 Imp.gals./min.)
Power steering : 9.8 L/min. (2.6 U.S.gals./min., 2.2 Imp.gals./min.)
Three point hitch SAE Category I
Max. lift
force
At lift points 750 kg (1655 lbs)
24 in. behind lift
points
590 kg (1300 lbs)
PTO system
Rear
PTO shaft SAE 1-3/8, 6 splines
Revolution 1 speed (540 rpm at 2600 engine rpm)
Mid.
PTO shaft USA No. 5 (KUBOTA 10-tooth) involute spline

8
W10357020
Model B2410D B2410DB B2410HDB
PTO power 14.3 kW (19.4 PS)* 13.4 kW (18.2 PS)*
Engine
Maker KUBOTA
Model D1105-D18
Bore and stroke 78 × 78.4 mm (3.07 × 3.09 in.).
(68.5 cu.in.)
Engine power (ECE-R24) 15.8 kW (21.5 PS)
Engine power
(SAE gross)
17.9 kW (24.0 HP)
Maximum torque 67 N·m (49.4 ft-lbs)
Capacities
Engine crankcase
(with filter)
3.0 L (3.2 U.S.qts., 2.6 Imp.qts.)
Transmission case 11.5 L (3.04 U.S.gals., 2.53 Imp.gals.) 12.5 L (3.30 U.S.gals.,
2.75 Imp.gals.)
Front axle case 3.7 L (3.9 U.S.qts.,
3.3 Imp.qts.)
4.5 L (4.8 U.S.qts., 4.0 Imp.qts.)
Tires
Front 6.00-12
Rear 9.5-18
Dimensions
Overall length (with 3P) 2430 mm (95.7 in.)
Overall width (min. tread) 1050 mm (41.3 in.)
Overall height
(with ROPS)
2298 mm (90.5 in.)
Overall height
(top of steering wheel)
1335 mm (52.6 in.)
Minimum ground
clearance 315 mm (12.4 in.)
Tread
Front 830 mm (32.6 in.)
Rear 810 to 1035 mm (31.9 to 40.7 in.)
Weight (with ROPS) 692 kg (1526 lbs) 702 kg (1548 lbs) 718 kg (1583 lbs)
Minimum turning
radius
Bi-speed turn
without brake
– 2.1 m (6.9 feet)
Travelling
system
Transmission Gear shift, 6 forward and 2 reverse HST with 2 speeds
range gear shift
Brake Wet disk type
Hydraulic
system
Pump capacity
Max. lift
force
24 in. behind lift
points
590 kg (1300 lbs)
PTO system
Rear
Mid.

9
W10368160
Model B2710HDB
PTO power 15.0 kW (20.4 HP)*
Engine
Maker KUBOTA
Model V1305-D18
Bore and stroke 76 × 73.6 mm (2.99 × 2.90 in.).
(81.5 cu.in.)
Engine power (ECE-R24) 18.2 kW (24.7 PS)
Engine power
(SAE gross)
20.1 kW (27.0 HP)
Maximum torque 79 N·m (59 ft-lbs)
Capacities
Engine crankcase
(with filter)
4.1 L (4.3 U.S.qts., 3.6 Imp.qts.)
Transmission case 15.5 L (4.10 U.S.gals., 3.41 Imp.gals.)
Front axle case 5.3 L (5.6 U.S.qts., 4.7 Imp.qts.)
Tires
Front 7-12 (180 / 85D12)
Rear 12.4 -16
Dimensions
Overall length (with 3P) 2625 mm (103.3 in.)
Overall width (min. tread) 1365 mm (53.7 in.)
Overall height
(with ROPS) 2334 mm (91.9 in.)
Overall height
(top of steering wheel)
1375 mm (54.1 in.)
Minimum ground
clearance
308 mm (12.1 in.)
Tread
Front 935 mm (36.8 in.)
Rear 1050 mm (41.3 in.)
Weight (with ROPS) 842 kg (1857 lbs)
Minimum turning
radius
Bi-speed turn
without brake
2.1 m (6.9 feet)
Travelling
system
Transmission Hydrostatic transmission with 3 speeds range gear shift
Brake Wet disk type
Hydraulic
system
Pump capacity
Max. lift
force
24 in. behind lift
points
650 kg (1433 lbs)
PTO system
Rear
Mid.

10
B1710 · B2110 · B2410 · B2710, WSM TRAVELLING SPEEDS
TRAVELLING SPEEDS
[Manual Transmission Model]
W10350650
[HST Model]
W10411340
Model B1710 B2110 B2410 B1710, B2110 B2410
Tire size (Rear) 8-16 9.5-16 9.5-18 31 × 13.5-15 315/75D-15
Range gear
shift lever
Maingear
shift lever
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
Forward
Low
1 0.9 (0.6) 1.0 (0.6) 1.1 (0.7) 0.9 (0.6) 1.0 (0.6)
2 1.7 (1.1) 1.8 (1.1) 1.9 (1.2) 1.6 (2.0) 1.8 (1.1)
3 3.0 (1.9) 3.2 (2.0) 3.4 (2.1) 2.9 (1.8) 3.2 (2.0)
High
1 5.3 (3.3) 5.6 (3.5) 6.0 (3.7) 5.2 (3.2) 5.6 (3.5)
2 9.3 (5.8) 9.8 (6.1) 10.5 (6.5) 9.1 (5.7) 9.9 (6.2)
3 16.8 (10.4) 17.8 (11.1) 19.1 (11.9) 16.5 (10.3) 17.9 (11.1)
Max. Speed
(at 2750
engine rpm)
3 17.8 (11.1) 18.8 (11.7) 20.2 (12.6) 17.4 (10.8) 19.0 (11.8)
Reverse
Low R 1.2 (0.7) 1.3 (0.8) 1.3 (0.8) 1.2 (0.7) 1.3 (0.8)
High R 6.6 (4.1) 7.0 (4.4) 7.5 (4.7) 6.4 (4.0) 7.0 (4.4)
Max. Speed
(at 2750
engine rpm)
R 7.0 (4.4) 7.4 (4.6) 7.9 (4.9) 6.8 (4.2) 7.4 (4.6)
Model B2110 B2410 B2110 B2410 B2710 B2710
Tire size (Rear) 9.5-16 9.5-18 31 × 13.5-15 315/75D-15 12.4-16 13.6-16
Range gear
shift lever
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
km/h
(mile/h)
Forward
Low
0 to 7.3
(0 to 4.5)
0 to 7.8
(0 to 4.8)
0 to 6.8
(0 to 4.2)
0 to 7.4
(0 to 4.6)
0 to 4.9
(0 to 3.0)
0 to 5.0
(0 to 3.1)
Middle – – – –
0 to 8.4
(0 to 5.2)
0 to 8.6
(0 to 5.3)
High
0 to 20.9
(0 to 13.0)
0 to 22.4
(0 to 13.9)
0 to 19.3
(0 to 12.0)
0 to 21.1
(0 to 13.1)
0 to 23.1
(0 to 14.4)
0 to 23.7
(0 to 14.7)
Max. Speed
(at 2750
engine rpm)
22.1 (13.7) 23.7 (14.7) 20.4 (12.7) 22.3 (13.9) 24.4 (15.2) 25.1 (15.6)
Reverse
Low
0 to 5.9
(0 to 3.7)
0 to 6.3
(0 to 3.9)
0 to 5.4
(0 to 3.4)
0 to 5.9
(0 to 3.7)
0 to 3.9
(0 to 2.4)
0 to 4.0
(0 to 2.5)
Middle – – – –
0 to 6.7
(0 to 4.2)
0 to 6.9
(0 to 4.3)
High
0 to 16.7
(0 to 10.4)
0 to 18.0
(0 to 11.2)
0 to 15.4
(0 to 9.6)
0 to 16.9
(0 to 10.5)
0 to 18.4
(0 to 11.4)
0 to 19.0
(0 to 11.8)
Max. Speed
(at 2750
engine rpm)
17.7 (11.0) 19.0 (11.8) 16.3 (10.1) 17.9 (11.1) 19.5 (12.1) 20.1 (12.5)

11
B1710 · B2110 · B2410 · B2710, WSM DIMENSIONS
DIMENSIONS

CONTENTS
GENERAL
1. FEATURES ...................................................................................................... G-1
2. TRACTOR IDENTIFICATION ......................................................................... G-2
3. GENERAL PRECAUTIONS ............................................................................ G-3
4. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING.. G-4
[1] WIRING...................................................................................................... G-4
[2] BATTERY................................................................................................... G-6
[3] FUSE.......................................................................................................... G-6
[4] CONNECTOR............................................................................................ G-6
[5] HANDLING OF CIRCUIT TESTER......................................................... G-7
5. LUBRICANTS FUEL AND COOLANT .......................................................... G-8
6. TIGHTENING TORQUES ............................................................................... G-9
[1] GENERAL USE SCREWS, BOLTS AND NUTS................................... G-9
[2] STUD BOLTS............................................................................................ G-9
7. MAINTENANCE ............................................................................................. G-10
8. CHECK AND MAINTENANCE..................................................................... G-11
[1] DAILY CHECK ........................................................................................ G-11
[2] CHECK POINTS OF INITIAL 50 HOURS........................................... G-12
[3] CHECK POINTS OF EVERY 50 HOURS........................................... G-15
[4] CHECK POINTS OF EVERY 100 HOURS......................................... G-17
[9] CHECK POINTS OF EVERY 1 YEAR ................................................ G-26
[10]CHECK POINTS OF EVERY 2 YEARS.............................................. G-26
[11]OTHERS .................................................................................................. G-29
9. SPECIAL TOOLS.......................................................................................... G-31
[1] SPECIAL TOOLS FOR ENGINE .......................................................... G-31
[2] SPECIAL TOOLS FOR TRACTOR....................................................... G-36
10. TIRES............................................................................................................. G-40
[1] TIRE PRESSURE ................................................................................... G-40
[2] TREAD..................................................................................................... G-41
(1) Front Wheels...................................................................................... G-41
(2) Rear Tread......................................................................................... G-42
[3] TIRE LIQUID INJECTION...................................................................... G-44

G-1
B1710 · B2110 · B2410 · B2710, WSM G GENERAL
1. FEATURES
1. Integral Power Steering
2. E-TVCS (Three Vortex Combustion System) Diesel Engine
3. Engine Key Shut-Off System
4. Hydrostatic Transmission (HST)
5. 3 Range of Speed (B2710 only)
6. Bi-speed Turn (Except B1710)
7. Wet Disc Brake
8. Standard mid-PTO
9. Simultaneous Mounting of Both the Mid. Mount Mower and Front Loader
10.Combination Panel of Easy Checker
11.Large Hydraulic Pump
12.Position Control Valve
13.Hydraulic Block Type Outlet
14.Foldable ROPS
15.Auxiliary Hydraulic Control Valve (Remote Valve)

G-2
2. TRACTOR IDENTIFICATION
When contacting your local KUBOTA distributor, always specify
engine serial number, tractor serial number and hour meter reading.
W10108050
(1) Tractor Identification Plate
(2) Tractor Serial Number
(3) Engine Serial Number
(4) Hour Meter

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

G-3
3. GENERAL PRECAUTIONS
• During disassembly, carefully arrange removed parts in a clean
area to prevent confusion later. Screws, bolts and nuts should be
installed in their original position to prevent reassembly errors.
• When special tools are required, use KUBOTA genuine special
tools. Special tools which are not frequently used should be
made according to the drawings provided.
• Before disassembling or servicing electrical wires, always
disconnect the ground cable from the battery first.
• Remove oil and dirt from parts before measuring.
• Use only KUBOTA genuine parts for parts replacement to
maintain machine performance and to assure safety.
• Gaskets and O-rings must be replaced during reassembly.
Apply grease to new O-rings or oil seals before assembling.
See the figure left side.
• When reassembling external snap rings or internal snap rings,
they must be positioned so that sharp edge faces against the
direction from which a force is applied. See the figure left side.
• When inserting spring pins, their splits must face the direction
from which a force is applied. See the figure left side.
• To prevent damage to the hydraulic system, use only specified
fluid or equivalent.
W10109040
(1) Grease
(2) Force
(3) Sharp Edge
(4) Axial Force
(5) Rotating Movement
(A) External Snap Ring
(B) Internal Snap Ring

G-4
4. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS
AND WIRING
To ensure safety and prevent damage to the machine and
surrounding equipment, heed the following precautions in handling
electrical parts and wiring.
IMPORTANT
■
• Check electrical wiring for damage and loosened
connection every year. To this end, educate the customer to
do his or her own check and at the same time recommend
the dealer to perform periodic check for a fee.
• Do not attempt to modify or remodel any electrical parts and
wiring.
• When removing the battery cables, disconnect the negative
cable first. When installing the battery cables, connect the
positive cable first.
W10111140
[1] WIRING
• Securely tighten wiring terminals.
W10112160
• Do not let wiring contact dangerous part.
W10113130
• Securely insert grommet.
W10113880
(1) Negative Terminal (2) Positive Terminal
(1) Correct
(Securely Tighten)
(2) Incorrect
(Loosening Leads to Faulty Contact)
(1) Dangerous Part
(2) Wiring (Incorrect)
(3) Wiring (Correct)
(4) Dangerous Part
(1) Grommet (A) Correct
(B) Incorrect

G-5
• Securely clamp, being careful not to damage wiring.
W10114580
• Clamp wiring so that there is no twist, unnecessary sag, or
excessive tension, except for movable part, where sag be
required.
W10115870
• In installing a part, take care not to get wiring caught by it.
W10116700
• After installing wiring, check protection of terminals and clamped
condition of wiring, only connect battery.
W10117350
(1) Clamp
• Wind Clamp Spirally
(2) Wire Harness
(3) Clamp
(4) Welding Dent
(1) Wiring
(2) Clamp
(A) Correct
(B) Incorrect
(1) Wiring (A) Incorrect
(1) Cover
• Securely Install Cover

KUBOTA B2410DB TRACTOR Service Repair Manual.pdf

Recommended

Recommended

More Related Content

Similar to KUBOTA B2410DB TRACTOR Service Repair Manual.pdf

Similar to KUBOTA B2410DB TRACTOR Service Repair Manual.pdf (19)

More from cml64801374

More from cml64801374 (20)

Recently uploaded

Recently uploaded (20)

KUBOTA B2410DB TRACTOR Service Repair Manual.pdf