This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and related components on a Caterpillar 3056E engine. The removal process involves taking out the engine oil pan, rotating the crankshaft, and pushing pistons and connecting rods out through the cylinder block. The installation is the reverse, cleaning components, lubricating, and inserting pistons from the top while the crankshaft positions the connecting rod journal at the bottom center. Special tools are required for tasks like removing piston rings and pins.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
The Future of Autonomous Vehicles | civilthings.com | Detailed informationgettygaming1
civilthings.com Present Autonomous vehicles, also known as self-driving cars, represent a groundbreaking advancement in transportation technology. These vehicles utilize sophisticated sensors, advanced software, and machine learning algorithms to navigate roads and transport passengers without human intervention. Major companies in the autonomous vehicle industry are investing heavily in the development and testing of these innovative machines, aiming to enhance safety, efficiency, and convenience on the roads.
The autonomous vehicle market is rapidly expanding, driven by technological progress and increasing consumer interest. With the advent of autonomous vehicle technology, the future of transportation promises significant changes, including reduced traffic accidents and lower emissions. However, the widespread adoption of autonomous vehicles faces challenges, such as regulatory hurdles, safety concerns, and public acceptance.
Autonomous vehicle regulations and legislation are evolving to address these issues, ensuring that the integration of self-driving cars into everyday life is smooth and secure. As the industry grows, news and trends related to autonomous vehicles continue to capture global attention. From the development of cutting-edge sensors to advancements in autonomous vehicle software, this sector is poised to revolutionize how we think about mobility.
Stay informed about the latest in autonomous vehicle technology, industry developments, and market trends to understand the profound impact these vehicles will have on our future.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i01548436
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: The naturally aspirated 3054 marine engine has one piston cooling jet that is located inside
the number one cylinder. The naturally aspirated 3056 marine engine is not equipped with piston
cooling jets.
Illustration 1 g00548374
Illustration 2 g00606467
1. Remove valve assembly (1) from piston cooling jet (2).
2. Remove piston cooling jet (2) from the cylinder block.
Note: The engine crankshaft may be rotated in order to access all of the piston cooling jets.
Note: Ensure that the ball moves freely within the valve assembly of the piston cooling jet.
Check that the tube of the piston cooling jet is not damaged.
3. Remove hollow dowel (3) from the cylinder block.
Note: Hollow dowel (3) is used to locate the piston cooling jet.
2/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Repeat Steps 1 through 3 for the removal of the remaining piston cooling jets.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00548374
Illustration 4 g00606467
1. Install piston cooling jet (2) to the cylinder block.
3/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: Ensure that piston cooling jet (2) is properly located on hollow dowel (3). Refer to the
Specifications Manual, "Piston Cooling Jet" for the correct procedure for the alignment of
the piston cooling jet.
2. Install valve assembly (1) into the piston cooling jet (2). Tighten the banjo bolt of the valve
assembly (1) to a torque of 20 N·m (15 lb ft).
3. Repeat Steps 1 through 2 for the installation of the remaining piston cooling jets.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:06:02 UTC+0800 2021
4/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i02414202
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2269 Ridge Reamer 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
C. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) in order to remove the liner wear ridge from the inner surface of the
cylinder liner.
2. Position the pistons that are being removed at the bottom center position.
1/2
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g00893856
Note: Do not reuse bolts (1) . Dispose of old bolts (1) and use new bolts (1) for the
installation procedure.
3. Remove bolts (1) from the connecting rod.
Illustration 2 g00633919
Note: The caps and rods must stay together as a pair. Do not stamp the new connecting rod.
For storage of the connecting rods and caps, tighten the bolts to 20 N·m (15 lb ft).
4. Remove connecting rod caps (2) and the connecting rod bearings.
5. Push the pistons and the connecting rods through the top of the cylinder block.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:06:58 UTC+0800 2021
2/2
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i02088687
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00551459
Typical example
1. Use Tooling (A) in order to remove three piston rings (1) from piston (2).
Illustration 2 g00551460
Typical example
2. Use Tooling (B) in order to remove retaining rings (3) that hold the piston pin in position.
3. Remove piston pin (4) from the piston.
Note: If the piston pin cannot be removed by hand, heat the piston to a temperature of
45 ± 5 °C (113 ± 9 °F). Do not use a torch to heat the piston.
4. Remove bearing (5) from connecting rod (6).
2/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 3 g00893862
5. Use a suitable press and a suitable adapter in order to remove piston pin bushing (7) from
connecting rod (6).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:07:54 UTC+0800 2021
3/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i02088688
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00893862
1. Ream piston pin bushing (7) in order to obtain a clearance of 0.0085 ± 0.0055 mm
(0.00030 ± 0.00020 inch) between the piston pin and the piston pin bushing.
2. Lubricate all components with clean engine oil.
3. Use a suitable press and a suitable adapter to install piston pin bushing (7) into connecting
rod (6).
Note: Ensure that the oil hole in the piston pin bushing is aligned with the oil hole at the top
of the connecting rod.
2/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g00551460
Typical example
4. Install bearing (5) in connecting rod (6).
5. Install piston pin (4) into the piston and through connecting rod (6).
Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of
45° ± 5°C (113° ± 9°F).
6. Use Tooling (B) in order to install retaining rings (3) that hold the piston pin in position.
Illustration 3 g00551459
7. Use Tooling (A) in order to install piston rings (1) on piston (2) with the following steps.
a. Install the oil control piston ring in the groove that is lowest on the piston. The latch
pin that is on the oil control ring must be inside the ends of the spring.
Note: Ensure that the latch pin that is on the oil control ring is 180 degrees from the
oil control ring gap.
b. Install the intermediate piston ring with the tapered face into the second groove on the
piston. The stamp "TOP" must be toward the top of the piston.
Note: Intermediate piston rings that are new have a green mark which must be on the
left of the piston ring gap when the piston ring is installed.
c. Position the piston ring gaps at 120 degrees away from each other.
d. Install the top piston ring with the barrel face and the molybdenum insert into the top
groove on the piston. The top piston ring has a wedge shape. The stamp "TOP" must
be toward the top of the piston.
Note: Top piston rings that are new have a red mark which must be on the left of the
ring gap when the ring is installed.
End By:
a. Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and
Connecting Rods - Install".
3/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:08:50 UTC+0800 2021
4/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i02414128
Pistons and Connecting Rods - Install
SMCS - 1225-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6684 Piston Ring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean all of the components.
2. Lubricate the piston and the cylinder liner with clean engine oil.
3. Rotate the crankshaft until the connecting rod journal is at the bottom center. Lubricate the
connecting rod journal with clean engine oil.
4. Lubricate the bearing for the upper connecting rod journal with clean engine oil.
1/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00634006
5. Install Tooling (A) on the piston.
Note: Ensure that Tooling (A) is installed correctly and that the piston can easily slide from
the tool.
Note: The arrow or the "FRONT" mark that is on the top of the piston must be toward the
front of the engine.
6. Push the piston and the connecting rod assembly into the cylinder liner and onto the
connecting rod journal.
Illustration 2 g00633919
7. Install the connecting rod bearings and connecting rod caps (2) .
2/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00893856
Note: Do not reuse bolts (1) . Use new bolts (1) during the installation.
8. Install new bolts (1) on the connecting rod. Tighten the new bolts to a torque of 70 N·m (52
lb ft). Tighten the new bolts for an additional 120 degrees.
9. Rotate the crankshaft in order to ensure that there is no binding.
10. Refer to Testing and Adjusting, RENR2416, "Piston Height - Inspect" for the correct
procedure on checking the height of the piston above the cylinder block.
End By:
a. Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
c. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:09:45 UTC+0800 2021
3/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i01746241
Connecting Rod Bearings - Remove
SMCS - 1219-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
b. Remove the engine oil relief valve. Refer to Disassembly and Assembly, "Engine Oil
Bypass Valve - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/2
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Dispose of all fluids according to local regulations and mandates.
1. In order to remove the connecting rod caps, rotate the crankshaft in a clockwise direction
until the piston is at the bottom center position.
Illustration 1 g00893992
2. Remove the nuts and bolts (1) from the connecting rod (2).
3. Remove connecting rod cap (3) and the lower connecting rod bearing together from
connecting rod (2).
Note: Check the location for each connecting rod cap on the crankshaft. Each connecting
rod cap must have a number that is identical to the number that is on the connecting rod. Do
not mix the bearings.
4. Carefully push the connecting rod into the cylinder liner. The connecting rod may need to
be rotated in order to prevent contact with the piston cooling jet. Remove upper connecting
rod bearing (4).
5. Repeat Steps 1 through 4 for the remaining connecting rod bearings.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:10:41 UTC+0800 2021
2/2
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i01749122
Connecting Rod Bearings - Install
SMCS - 1219-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00893992
1/2
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 1. Clean upper connecting rod bearing (4) and lubricate the bearing face with clean engine oil.
2. Clean lower connecting rod cap (3) and the lower connecting rod bearing. Lubricate the
bearing face with clean engine oil.
Note: Align the tabs on the connecting rod bearings with the tab grooves in the connecting
rod.
3. Pull the connecting rod into position against the crankshaft. The connecting rod may need to
be rotated in order to prevent contact with the piston cooling jet.
4. Install connecting rod cap (3) and the lower connecting rod bearing together in connecting
rod (2).
5. Install bolts (1) and the nuts in the connecting rod (2). Tighten bolts (1) to a torque of
155 N·m (114 lb ft). Tighten the nuts to a torque of 125 N·m (92 lb ft).
6. Repeat Steps 1 through 5 for the remaining connecting rod bearings.
End By:
a. Install the engine oil relief valve. Refer to Disassembly and Assembly, "Engine Oil Relief
Valve - Remove and Install".
b. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:11:37 UTC+0800 2021
2/2
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i01758964
Crankshaft Main Bearings - Remove
SMCS - 1203-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6282 Torque Wrench Extension 1
Start By:
a. Remove the engine oil relief valve and the oil strainer. Refer to Disassembly and Assembly,
"Engine Oil Relief Valve - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Remove the following components from the engine in order to remove the rear main
bearing with the crankshaft in position: flywheel, flywheel housing, rear oil seal housing and
bridge assembly.
Note: Use Tooling (A) in order to remove the front main bearing cap with the front housing and
the engine oil pump in place. If Tooling (A) is not available, removal of the front cover and the
engine oil pump will be necessary. The engine oil pump is attached to the front main bearing cap.
1/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Removal of the bolts is not possible with a socket. Refer to Disassembly and Assembly, "Engine
Oil Pump - Remove".
1. Remove all necessary components in order to gain access to the specific main bearing cap.
2. Make sure that the main bearing cap is marked for the location and direction for installation.
The main bearings and the main bearing caps must be installed in the same location.
Illustration 1 g00554537
3. Remove two bolts (1) and main bearing cap (2).
Illustration 2 g00554539
4. Remove lower main bearing (3) from main bearing cap (2). Keep the respective main
bearing and the main bearing cap together for proper installation.
2/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g00554540
5. Push upper main bearing (4) from the opposite side of the bearing tab with a suitable tool.
Carefully rotate the crankshaft while you push on the bearing. Remove upper main bearing
(4) from the cylinder block. Keep the upper bearing halves together in order to ensure
proper installation.
6. Repeat Steps 1 through 5 for the remaining main bearings.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:12:33 UTC+0800 2021
3/3
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i01758965
Crankshaft Main Bearings - Install
SMCS - 1203-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6282 Torque Wrench Extension 1
B 8T-5096 Dial Indicator 1
(1)
Tooling (A) must be used in order to install the front main bearing cap with the front housing and the engine oil
pump in place.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00554540
1. Clean upper main bearing (4) and lubricate the bearing surface with clean engine oil.
Note: Ensure that the upper halves of the main bearings are installed so that the bearing tabs
fit into the notch in the cylinder block.
NOTICE
Only the upper half of the main bearing has lubrication holes. Make
sure the upper half of the main bearing is installed correctly in the
cylinder block to ensure proper lubrication.
2. Slide upper main bearing (4) into position between the crankshaft journal and the cylinder
block.
Illustration 2 g00554539
3. Clean main bearing cap (2) and lower main bearing (3). Lubricate the bearing surface of
lower main bearing (3) with clean engine oil.
Note: Ensure that the lower halves of the main bearings are installed so that the bearing tabs
fit into the notch in the main bearing caps.
2/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 4. Install lower main bearing (3) in main bearing cap (2).
Illustration 3 g00554537
5. Make sure that the bearing tabs on both halves of the main bearings are located on the same
side. Install main bearing caps (2).
6. Lubricate the threads of bolts (1) with clean engine oil.
7. Install bolts (1). Tighten bolts (1) to a torque of 250 N·m (185 lb ft). Use Tooling (A) to
tighten the bolts for the front main bearing cap.
8. Repeat Steps 1 through 7 for the remaining main bearings.
9. Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Illustration 4 g00555578
Typical example
10. Check the crankshaft end play. Use a prybar to move the crankshaft toward the rear of the
engine. Install Tooling (B) and zero the dial indicator. Move the crankshaft with the prybar
toward the front of the engine. Measure the crankshaft end play. The maximum permissible
crankshaft end play is 0.51 mm (0.020 inch).
Note: If the crankshaft was not removed for the rear main bearing removal, the following
components must be installed: bridge assembly, rear oil seal housing, flywheel housing and
flywheel.
3/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. End By:
a. Install the engine oil relief valve and the oil strainer. Refer to Disassembly and Assembly,
"Engine Oil Relief Valve - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:13:29 UTC+0800 2021
4/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-583E VIBRATORY COMPACTOR CNX
Configuration: CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
3056E Engine for Caterpillar Built Machines
Media Number -RENR2400-06 Publication Date -01/02/2006 Date Updated -03/05/2017
i01757227
Crankshaft - Remove
SMCS - 1202-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
b. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
c. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
d. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
e. Remove the housing for the crankshaft rear seal. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 1 g00541252
1. Remove socket head bolts (1) from the bridge.
2. Remove bridge (2) from the cylinder block.
Illustration 2 g00572309
Note: Inspect the main bearing caps and the connecting rod caps for the proper
identification mark. The identification marks should give the location and the direction of
the bearings in the engine.
3. Remove main bearing cap bolts (3).
4. Remove main bearing caps (4) from the cylinder block.
5. Remove the lower main bearings and the lower thrust washers. Keep the lower main
bearings with the respective main bearing cap.
2/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 3 g00541254
Note: The connecting rod caps are held on the connecting rod with bolts that are threaded
into the connecting rod.
6. Remove bolts (5) from the connecting rods.
7. Remove connecting rod caps (6) from the connecting rods.
8. Remove the bearings from connecting rod caps (6). Keep the connecting rod bearings with
the respective connecting rod cap.
NOTICE
Do not allow the connecting rods to strike the piston cooling jets.
Damage or misalignment may occur.
9. Push the piston assemblies into the cylinder bores.
Illustration 4 g00572311
10. Attach lifting straps and a suitable lifting device to crankshaft (7).
3/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. 11. Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is approximately
39 kg (85 lb). Do not scratch any of the finished surfaces on the crankshaft.
Illustration 5 g00541257
12. Remove upper main bearings (8) and upper thrust washers (9).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 20 01:14:25 UTC+0800 2021
4/4
CS-583E CP-583E Vibratory Compactor CNX00001-UP (MACHINE) POWERED B...
2021/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...