cellphone detector

17,372 views

Published on

What it is: This is a circuit for a mobile transmission detector which can detect use of a mobile phone within the range of 1.5 meters. Whenever usage of mobile phone is detected such as calling or texting a beep alarm starts sounding and a led blinks.
Why it is: This handy, pocket-size mobile transmission detector can sense the presence of an activated mobile phone from a distance of one and a-half meters.
Where it is used: it can be used to prevent use of mobile phones in examination halls, confidential rooms, etc. It is also useful for detecting the use of mobile phone for spying and unauthorized video transmission.

Published in: Education
1 Comment
16 Likes
Statistics
Notes
No Downloads
Views
Total views
17,372
On SlideShare
0
From Embeds
0
Number of Embeds
7
Actions
Shares
0
Downloads
1,743
Comments
1
Likes
16
Embeds 0
No embeds

No notes for slide

cellphone detector

  1. 1. ByMANASA (09881A0473)VENU GOPAL (09881A04A8)
  2. 2. CELLPHONE DETECTOR: Fig: i-phone
  3. 3. Introduction:  This is a circuit for a mobile transmission detector which can detect use of a mobile phone within the range of 1.5 meters.  Whenever usage of mobile phone is detected such as calling or texting a beep alarm starts sounding and a led blinks.  It can be used to prevent use of mobile phones in examination halls, confidential rooms, etc. It is also useful for detecting the use of mobile phone for spying and unauthorized video transmission.
  4. 4. How to make:  It can detect both incoming and outgoing calls, SMS and video transmission even if the mobile phone is kept in the silent mode.  The moment it detects RF transmission signal from an activated mobile phone, it starts sounding a beep alarm and the LED blinks.  The transmission frequency of mobile phones ranges from 0.9 to 3 GHz with a wavelength of 3.3 to 10 cm. So a circuit detecting Gigahertz signals is required for a mobile bug.
  5. 5. GSM PHONES: Fig: GSM phones
  6. 6. CIRCUIT DIAGRAM:
  7. 7. COMPONETS USED: Antenna 5-INCH LONG Capacitors 22p(2),0.22µ(1),100 µ(1),47p(1), 0.1 µ(2),0.01 µ(1),4.7 µ(1) Resistors 2.2M(2),200K,100K,1K,12K,15K, IC CA3130,NE555 LED 1 Transistor BC548 BUZZER ON/OFF SWITCH POWER SUPPLY 16V BATTERY 12V
  8. 8. OPERATION:  Here the circuit uses a 0.22μF disk capacitor (C3) to capture the RF signals from the mobile phone.  The lead length of the capacitor is fixed as 18 mm with a spacing of 8 mm between the leads to get the desired frequency.  The disk capacitor along with the leads acts as a small Gigahertz loop antenna to collect the RF signals from the mobile phone.
  9. 9.  Op-amp IC CA3130 (IC1) is used in the circuit as a current-to-voltage converter with capacitor C3 connected between itsinverting and non-inverting inputs. It is a CMOS version using gate-protected p-channel MOSFETtransistors in the input to provide very high input impedance,very low input current and very high speed of performance. The output CMOS transistor is capable of swinging the outputvoltage to within 10 mV of either supply voltage terminal. Capacitor C3 in conjunction with the lead inductance acts as atransmission line that intercepts the signals from the mobilephone.
  10. 10.  This capacitor creates a field, stores energy and transfers thestored energy in the form of minute current to the inputs of IC1. This will upset the balanced input of IC1 and convert thecurrent into the corresponding output voltage. Capacitor C4 along with high-value resistor R1 keeps the non-inverting input stable for easy swing of the output to high state. Resistor R2 provides the discharge path for capacitor C4.Feedback resistor R3 makes the inverting input high when theoutput becomes high.
  11. 11. Fig: Different types of cellphones
  12. 12.  Capacitor C5 (47pF) is connected across ‘strobe’ (pin 8) and‘null’ inputs (pin 1) of IC1 for phase compensation and gaincontrol to optimize the frequency response. When the mobile phone signal is detected by C3, the output ofIC1 becomes high and low alternately according to the frequencyof the signal as indicated by LED1. This triggers constable timer IC2 through capacitor C7.Capacitor C6 maintains the base bias of transistor T1 for fastswitching action. The low-value timing components R6 and C9 produce veryshort time delay to avoid audio nuisance.
  13. 13. Fig: circuit detecting a phone
  14. 14. CONCLUSION and FUTURE SCOPE CONCLUSION This pocket-size mobile transmission detector or sniffer cansense the presence of an activated mobile cell phone from a distanceof one and-a-half meters. So it can be used to prevent use of mobile phones in examinationhalls, confidential rooms, etc. It is also useful for detecting the use ofmobile phone for spying and unauthorized video transmission. FUTURE SCOPE Trying to increase the detecting range of cell phone detector tofew more meters for observing wide range of area.
  15. 15. Fig: Led blinking
  16. 16. References: 1.www.google.com 2.www.wikipedia.org 3.www.pdfmachine.com 4.www.efymag.com 5.www.datasheets4u.com
  17. 17. THANK YOU....

×