Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.



Published on

Published in: Technology, Art & Photos
  • Be the first to comment

  • Be the first to like this


  1. 1. Splitcoaststampers - Tutorial Page 1 of 9 the stamper's community Hidden Message Slider by Beate Johns Everyone will love this slider that reveals a hidden message when you pull on the tag. Supplies Cardstock for card base 4 1/4" x 5 1/2" (here Chocolate Chip) Cardstock for slider base 5 1/4" x 8 1/2" (here Pumpkin Pie) Cardstock for sliding tag 3 3/4" x 4 1/2" (here Always Artichoke) Cardstock for image or first layer of image 2 1/4" x 2 1/4" (here Tempting Turquoise) Cardstock for hidden message piece 2 1/2" x 3 3/4" (here Pink Passion) Paper punch of your choice for pull tab Paper cutter with cutting and scoring blade Sticky Strip™ Stamps Inks Embellishments Stapler Step-by-Step Step 1 Place slider base cardstock into the paper cutter horizontally and score at 4" and 8". 4/4/2008
  2. 2. Splitcoaststampers - Tutorial Page 2 of 9 Step 2 Insert the slider base cardstock back into the paper cutter horizontally with the glue tab (1/2" strip) facing to the right. Line it up on the 1 1/4" mark and cut from 3/4" to 4 1/2" to make the first slit for the slider. Step 3 Move the cardstock over to the 3 3/4" mark and make the same cut from 3/4" to 4 1/2". Step 4 The section with the slits will be the card front. Stamp this section. 4/4/2008
  3. 3. Splitcoaststampers - Tutorial Page 3 of 9 Step 5 Pre-fold at all scored lines. Step 6 Stamp the message on both ends of the hidden message cardstock. Only about 1" on each end will be seen when the card is finished. 4/4/2008
  4. 4. Splitcoaststampers - Tutorial Page 4 of 9 Step 7 Tape the hidden message piece between the slits on the front of the slider base. Step 8 Insert the 3 3/4" x 4 1/2" slider tag cardstock horizontally into the paper cutter. Line it up at 2 1/2" and cut from the bottom to 3 1/2". Step 9 4/4/2008
  5. 5. Splitcoaststampers - Tutorial Page 5 of 9 Take the card slider base and turn it stamped side down. Insert slider tag cardstock through both slits. Step 10 Staple the slider tag cardstock together where the cut is. Step 11 Take a punch and punch a little opening on the bottom of the slider front. That will make it easier to pull the slider tag out. 4/4/2008
  6. 6. Splitcoaststampers - Tutorial Page 6 of 9 Step 12 Decorate the part of the slider tag that shows between the slits. I added a piece of turquoise cardstock and then the cut out flower and leaves. Step 13 Add Sticky Strip™ to the glue tab and tape the slider base together. 4/4/2008
  7. 7. Splitcoaststampers - Tutorial Page 7 of 9 Step 14 Pull the slider tag out and add embellishment to the pull tab if desired. I added a turquoise punched circle and some ribbon. 4/4/2008
  8. 8. Splitcoaststampers - Tutorial Page 8 of 9 Step 15 Adhere the card to the 4 1/4" x 5 1/2" card base. Add eyelets or brads to the top of the card as long as they are above the point where the slider slits end. 4/4/2008
  9. 9. Splitcoaststampers - Tutorial Page 9 of 9 Variations Try Different Sizes When changing the measurements, here are some hints: Slider tag size Height: As high as from the bottom of your slider base to the end of the slits. Width: 1/4" smaller than card front. Sliding image Width: 1/4" smaller as distance between both slits (if you want it layered). You could also just layer a bigger image over it with dimensionals. Height: As long as the slit in your slider tag (see step 8). Your Turn You've seen the tutorial, now you try it! We've got a section of the gallery set aside for Hidden Message Slider. Try this technique, then upload your artwork to the gallery. Show us your creations! contact us | calendar | advertise | terms of service Copyright ©2003-2007, 4/4/2008