Session Plan-7 (M01-LO7)Unit of Competence      Set-out Masonry StructuresModule Title            Setting-out Masonry Stru...
Evidence Plan TVET Program: Learning Outcomes / Modules covered Batch Class                     Ways in which evidence wil...
Session Plan ____Unit of Competence :        perform minor maintenanceModule Title :              minor maintenanceLO 01_ ...
Session Plan ____Unit of Competence :        perform minor maintenanceModule Title :              minor maintenanceLO 02_ ...
Session Plan ____Unit of Competence :        perform minor maintenanceModule Title :              minor maintenanceLO 03_ ...
Upcoming SlideShare
Loading in …5
×

Session plan

484 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
484
On SlideShare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
9
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Session plan

  1. 1. Session Plan-7 (M01-LO7)Unit of Competence Set-out Masonry StructuresModule Title Setting-out Masonry StructuresLO7 Clean upSession Objectives: At the end of this session the trainees shall be able to – clear work area and dispose reused or recycled materials in accordance with legislation/regulations/codes of practice and job specification clean, check, maintain and store tools and equipment in accordance with manufacturers’ recommendations and standard work practices NominalActivities Contents Methods DurationIntroduction 10 mins Recapitulation DiscussionSessions 30 mins Housekeeping and 5S Lecture-discussion Tools and Equipment Cleaning 20 mins Lecture-discussion and Maintenance Concept and Procedures of Lecture-discussion 30 mins Material Disposal, Recycling and Demonstration and Reuse 15 mins Waste Management Lecture-discussionEvaluation 45 mins Accomplishment of LAP Test Individual ActivitySummary 5 mins Wrap-up and Feedback Question & AnswerResources Learning Guide #7 Sample materials Masonry common tools and equipment
  2. 2. Evidence Plan TVET Program: Learning Outcomes / Modules covered Batch Class Ways in which evidence will be collected: Demonstration Knowledge Questioning LAP Test with Oral TestThe evidence must show that the student……*Critical aspect of competence Prepared by: Date: Checked by: Date:
  3. 3. Session Plan ____Unit of Competence : perform minor maintenanceModule Title : minor maintenanceLO 01_ : prepare for minor maintenanceSession Objectives: At the end of this session the learners shall be able to – Identification, selection and provision of tools,suppliesandmaterials for maintenanceonsite accordingtosupervisorsinstructions Regularoperationalchecksofmachineryand equipment Identification and segregation of faulty or unsafe machine/equipment for repair/replacement according toenterpriserequirements Identification of Faultyor unsafemachineryandequipment for repair or replacement accordingto enterpriserequirements Identification of OHS hazards intheworkplace Nominal Learning Activities Contents Duration MethodsIntroductionSessionsEvaluationSummaryResources
  4. 4. Session Plan ____Unit of Competence : perform minor maintenanceModule Title : minor maintenanceLO 02_ : carry out minor maintenanceSession Objectives: At the end of this session the learners shall be able to – Selecting using suitablepersonalprotectiveequipment accordingtoOHS requirements Greasing,lubricationandotherbasicservicingof machineryandequipment accordingto operator’smanual/manufacturers specifications and supervisorsinstructions. Regular adjustmentsandrepairs accordingtooperators manual/manufacturers’specificationsandsupervisors instructions conducting work according to OHSrequirementsand supervisor’srequirements Nominal Learning Activities Contents Duration MethodsIntroductionSessionsEvaluationSummaryResources
  5. 5. Session Plan ____Unit of Competence : perform minor maintenanceModule Title : minor maintenanceLO 03_ : complete minor maintenanceSession Objectives: At the end of this session the learners shall be able to – cleaning, returning and storing tools accordingto manufacturers’specifications and enterpriserequirements followingEnvironmentalprocedures and collecting, treating and disposing/recycling waste from maintenanceactivities Maintenance and clearance of Workarea accordingtoOHS and enterprise requirement Reporting Malfunctions,faults, wear or damage oftools tothesupervisor accordingtoenterprise requirements Nominal Learning Activities Contents Duration MethodsIntroductionSessionsEvaluationSummaryResources

×