Mpt2 printer for SkidWeigh products

193 views

Published on

Mobile mini thermal printer for lift truck load weight printout ticket from Freightweight, SkidWeigh systems

Published in: Business, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
193
On SlideShare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
0
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Mpt2 printer for SkidWeigh products

  1. 1. MPT2 SeriesMINI MOBILE THERMAL PRINTER
  2. 2. PAPER LOADINGInsert paper roll into paper case. Pay attentionto the direction of the paper. Pull paper out ofpaper case. From the bottom of the paper rollinsert the paper into the slot and press FEEDbutton. Make sure paper is in the center, thanclose upper cover.PRINTER MOUNTING BRACKETOn-board printer mounting bracketPRINTER INTERFACE• Data Transfer: Serial• Synchro Mode: Asynchronous• Handshaking: Hardware RST/CTS• Signal Level: RS-232• Baud Rate: 1200,2400,4800,9600• Data Bit: 7bit, 8 bit optional• Parity: Odd,Even,None optional• Stop Bit: 1 bitSTANDARD ACCESSORIES• Rechargeable Li-ion battery• Paper Roll• Environmental Case• Interface Cable RS-232• Power cableFEATURES• The smallest 2” mobile printer• Lightest weight for true mobility• High speed thermal method printing• Support text and graphic printing• 1.2 m free fall into concreteThe MPT2 Mini Mobile Thermal Printer uses a Lithium rechargeable battery pack. Before the first use the battery pack shouldbe charged for at least 4 hours. (If the printer not connected directly to the SkidWeigh product line)Use two fingers topress this place andopen the upper coverUpperCoverPowerinput cable
  3. 3. THERE ARE TWO LED INDICATORS FOR MPT2 PRINTERLED indicators show current status and buzzer indicates the changes of statusTHERE ARE TWO LED INDICATORS FOR MPT2 PRINTERLED indicators show current status and buzzer indicates the changes of statusTHERE ARE TWO LED INDICATORS FOR MPT2 PRINTERLED indicators show current status and buzzer indicates the changes of statusTHERE ARE TWO LED INDICATORS FOR MPT2 PRINTERLED indicators show current status and buzzer indicates the changes of statusPRINTER’S TWO LED INDICATORS AND BUZZERPRINTER’S TWO LED INDICATORS AND BUZZERPRINTER’S TWO LED INDICATORS AND BUZZERPRINTER’S TWO LED INDICATORS AND BUZZERLED LIGHT INDICATOR(BLUE)LED LIGHT INDICATOR(RED)STATUS BUZZERFlash quickly Dark ChargingFlash slowly Dark Out of powerContinuously bright Dark Charging finishedDark Continuously bright WorkingFlash slowly Flash slowly Paper end WarningDark Flash slowly StandbyPRINTER ON / OFFThe printer is powered on by pressing the power button for about one second.The Red solid LED light (Left) will be activated.To turn power to the printer OFF, press power button again for about 2 second.(When printer is turned OFF all LED’s will be turned off as well)Note: When power indicator LED red light is changed to blue color and is blinkingthis indicates that the printer battery must be charged. (If printer not connected toSkidWeigh products)SELF TESTPAPER FEEDINGPAPER TEARINGThe self-test checks the printer’s current settings, status and whether the printerhas any problems. To activate the self-test turn holding down the FEED button whilepress power button for about 3 seconds. The printer is ready to receive data assoon as it completes the self-test.During the normal operation to feed paper hold down FEED button.To stop paper feed release FEED button.After each print out ticket / receipt is finished printing, tear off the paper along thetear bar.Note: When tearing do not use too much force in order to avoid paper being pulledout from the paper case.OperationalSpecificationsFEEDBUTTONPOWERBUTTON
  4. 4. GeneralSpecificationsMODEL MPT2Physical SpecificationsDimensions 92.5 x 75 x 38 mmWeight 205 g (Paper roll excluded)Paper Diameter Max. 40 mmPrinting SpecificationsPrinting Method Line thermalPaper Width 58 mmDot / line 384 dotsPrinting Speed 50 - 80 mm/sPaper Thickness 0.06 - 0.085 mmBlack Mark Checking AvailablePaper roll diameter 30 mmBuilt in Character Set English: ASCII (8 x 8 / 12 x 12)Interface SpecificationsCable Connection RS-232Wireless (Optional) IrDA / BluetoothPower SpecificationsBattery 1500mAh /7.4VPower Adaptor * 12 V DC / 1.5ABattery Duration 150 - 200 m continuous printing (25% density)Environmental SpecificationsOperationTemperature / Humidity-10 C - 50 C20% - 80%ChargingTemperature . Humidity5 C - 35 C20% - 80%StorageTemperature / Humidity-20 C - 60 C5% - 95%* Power Connection toSkidWeigh ProductsDirect power connection cable toSkidWeigh products operating from 12 V DC to 55 V DCIntegrated Visual Data Technology Inc.3439 Whilabout TerraceOakville, OntarioCanada L6L 0A7Phone: 905-469-0985Fax: 905-825-9494 MPT2 Mini Mobile Thermal Printer V.10InfraredinterfaceRS-232socketPrinterbracket

×