Patent Pending Keep it watertight  with Welded steel anchor Wood/Steel anchor Concrete anchor Sealable scaffold attachment...
THE PROBLEM Water intrusion at conventional push pull wire ties. THE SOLUTION Sealable scaffold attachments. Bumperite Wat...
<ul><li>SAFETY OSHA compliant </li></ul><ul><li>Engineered and tested structural attachment for scaffolding (4500) lbs. Re...
Welded Steel Anchor INSTALLATION PROCEDURE <ul><li>Determine spacing requirement to insure safe scaffold erection.*  </li>...
Bumperite Attachment To Steel Bent Plate Illustrations and load Capacity provided by  FICCADENTI & WAGGONER , Consulting S...
WOOD INSTALLATION PROCEDURE <ul><li>Determine spacing requirement to insure safe scaffold erection.* </li></ul><ul><li>Rev...
Bumperite Attachment to Wood Framing Allowable Screw withdraw Value (P): Allowable Nail Withdraw Value (P): Illustrations ...
STEEL FRAMED INSTALLATION PROCEDURE <ul><li>Determine spacing requirement to insure safe scaffold erection.* </li></ul><ul...
Bumperite Attachment to Light Gauge Framing Minimum Design Requirements : : ALLOWABLE FORCE  (P) = 1,000 LBS. <ul><li>For ...
Bumperite Attachment to Light Gauge Framing Minimum Design Requirements : : ALLOWABLE FORCE  (P) = 500 LBS.  <ul><li>For s...
CONCRETE INSTALLATION PROCEDURE <ul><li>Determine Bumperite spacing requirement and  concrete psi values suitable for safe...
Bumperite Attachment to Concrete Deck   Illustrations and load Capacity provided by  FICCADENTI & WAGGONER , Consulting St...
BUMPERITE  QUICK-TAB Optional feature <ul><li>The specially designed Quick-tab is a scaffold erectors dream. </li></ul><ul...
Bumperite Quick-Tab Attachment Illustrations and load Capacity provided by  FICCADENTI & WAGGONER , Consulting Structural ...
Manufacturer recommends the use of Densglass Gold exterior sheathing, butyl sealant, Tyvek Straight Flash, minimum UU-B-79...
Step by Step   Patent Pending
Water tested to  ASTM E 1105-00  &  ASTM E 331-00  by Architectural Testing, Inc. Report No: 90353.01-701-43 WARRANTY: Bum...
Step by Step at wood / steel framed plates   Patent Pending
BUMPERITE - VS - WIRE TIES Testing at Smith-Emery Laboratories suggest that the Bumperite Waterguard peak tension load is ...
Upcoming SlideShare
Loading in …5
×

Bumperite Catalogue #2

447 views

Published on

Published in: Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
447
On SlideShare
0
From Embeds
0
Number of Embeds
14
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Bumperite Catalogue #2

  1. 1. Patent Pending Keep it watertight with Welded steel anchor Wood/Steel anchor Concrete anchor Sealable scaffold attachment system for exterior plaster Enhance Safety and Eliminate Water Intrusion at Scaffold Ties Toll Free (877) 490-8884
  2. 2. THE PROBLEM Water intrusion at conventional push pull wire ties. THE SOLUTION Sealable scaffold attachments. Bumperite Waterguards enhance Safety and eliminate Liability due to leaks caused by conventional scaffold wire ties assemblies . Patent Pending
  3. 3. <ul><li>SAFETY OSHA compliant </li></ul><ul><li>Engineered and tested structural attachment for scaffolding (4500) lbs. Report # L-06-3265 </li></ul><ul><li>Ideal for tarped or enclosed scaffolds in high wind conditions. </li></ul><ul><li>REDUCED LABOR COST </li></ul><ul><li>Eliminate costly end laps and their cuts to building papers verses conventional scaffold wire ties. </li></ul><ul><li>Removable bumper allows easy access to difficult work areas.* Promotes the continuous installation of building materials. </li></ul><ul><li>RELIABILITY Water tested to ASTM E331-00 at Smith-Emery laboratories, Inc. Los Angeles, CA. Report # L-06-3059 </li></ul>* See installation instructions. WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection and seals therewith. Patent Pending
  4. 4. Welded Steel Anchor INSTALLATION PROCEDURE <ul><li>Determine spacing requirement to insure safe scaffold erection.* </li></ul><ul><li>Measure distance between slab edge bent plate and outer face of stud framing. </li></ul><ul><li>Cut the anchor strut to length as to flush out with face of stud framing. </li></ul><ul><li>Align the anchor strut with the bent plate and stud framing (true, square, and plumb) per detail. </li></ul><ul><li>Weld anchor strut to building bent plate per welding detail shown. </li></ul><ul><li>The use of a certified welder and E7018 rod or equal is recommended. </li></ul>*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation . The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment. 1/8” Patent Pending
  5. 5. Bumperite Attachment To Steel Bent Plate Illustrations and load Capacity provided by FICCADENTI & WAGGONER , Consulting Structural Engineers, Inc
  6. 6. WOOD INSTALLATION PROCEDURE <ul><li>Determine spacing requirement to insure safe scaffold erection.* </li></ul><ul><li>Review screw matrix provided to determine screw size and quantity required for safe installation. </li></ul><ul><li>Install Bumperite anchor plate where suitable framing and or backing occurs to ensure sufficient strength required to carry intended scaffold load. </li></ul><ul><li>Apply compatible sealant between Bumperite anchor plate & building papers to ensure seal at screws. </li></ul><ul><li>Ensure complete screw embedment at pre-drilled holes in anchor plate. </li></ul>*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation . The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment. See engineered detail. Patent Pending
  7. 7. Bumperite Attachment to Wood Framing Allowable Screw withdraw Value (P): Allowable Nail Withdraw Value (P): Illustrations and load Capacity provided by FICCADENTI & WAGGONER , Consulting Structural Engineers, Inc 810 lbs. 810 lbs. 540 lbs. 270 lbs. #10 x 1 1 ∕ 2 &quot; Screw 1232 lbs. 1080 lbs. 720 lbs. 360 lbs. #10 x 2&quot; Screw 1232 lbs. 924 lbs. 616 lbs. 308 lbs. #12 x 1 1 ∕ 2 &quot; Screw 1232 lbs. 1080 lbs. 820 lbs. 410 lbs. #12 x 2&quot; Screw w/ 8 Fasteners w/ 6 Fasteners w/ 4 Fasteners w/ 2 Fasteners Fastener Type (Screw Size x Length) 144 lbs. 108 lbs. 72 lbs. 36 lbs. 10d Nail 160 lbs. 120 lbs. 80 lbs. 40 lbs. 16d Nail w/ 8 Fasteners w/ 6 Fasteners w/ 4 Fasteners w/ 2 Fasteners Fastener Type
  8. 8. STEEL FRAMED INSTALLATION PROCEDURE <ul><li>Determine spacing requirement to insure safe scaffold erection.* </li></ul><ul><li>Review backing plate requirements. </li></ul><ul><li>Install Bumperite anchor plate over 12 gage backing plate per diagram to ensure sufficient strength required to carry intended scaffold load. </li></ul><ul><li>Apply compatible sealant between Bumperite anchor plate & building papers to ensure seal at screws. </li></ul><ul><li>Ensure complete screw embedment at pre-drilled holes in anchor plate. </li></ul>*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation . The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment. See engineered detail. Patent Pending
  9. 9. Bumperite Attachment to Light Gauge Framing Minimum Design Requirements : : ALLOWABLE FORCE (P) = 1,000 LBS. <ul><li>For scaffold application this product complies w/ OSHA requirements </li></ul><ul><li>12 ga. Deck Edge Clip </li></ul><ul><li>18 ga. Wall Studs </li></ul><ul><li>8”x12 ga.x11/2” Fl. Track </li></ul><ul><li>Track Blocking must be located within 6” of the Deck Edge Clip </li></ul>Illustrations and load Capacity provided by FICCADENTI & WAGGONER , Consulting Structural Engineers, Inc
  10. 10. Bumperite Attachment to Light Gauge Framing Minimum Design Requirements : : ALLOWABLE FORCE (P) = 500 LBS. <ul><li>For scaffold application this product complies w/ OSHA requirements </li></ul><ul><li>12 ga. Deck Edge Clip </li></ul><ul><li>18 ga. Wall Studs </li></ul><ul><li>6”x16 ga.x1-1/2” Fl. Track </li></ul><ul><li>Track Blocking must be located within 6” of the Deck Edge Clip </li></ul>Illustrations and load Capacity provided by FICCADENTI & WAGGONER , Consulting Structural Engineers, Inc 6” x 16GA x 1-1/2” FLANGE TRACK W / CUPPED FLANGES @ ENDS EXTEND WEB TAB ATTACHMENT TO (E) STUD AS SHOWN (4) # 8 S.M.S. EA. END ALT. #1
  11. 11. CONCRETE INSTALLATION PROCEDURE <ul><li>Determine Bumperite spacing requirement and concrete psi values suitable for safe scaffold erection.* </li></ul><ul><li>Install Bumperite anchor plate at concrete slab edge with a minimum of two concrete anchors bolts, see engineered detail. </li></ul><ul><li>Install concrete anchors per manufactures installation guidelines. </li></ul><ul><li>Ensure complete anchor bolt </li></ul><ul><li>embedment for maximum strength. </li></ul>*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation . The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment. See engineered detail. Patent Pending
  12. 12. Bumperite Attachment to Concrete Deck Illustrations and load Capacity provided by FICCADENTI & WAGGONER , Consulting Structural Engineers, Inc
  13. 13. BUMPERITE QUICK-TAB Optional feature <ul><li>The specially designed Quick-tab is a scaffold erectors dream. </li></ul><ul><li>Fast and easy installation with no hassle. </li></ul><ul><li>A temporary attachment to building slab edge during scaffold erection prior to exterior wall framing and final welded attachment of Bumperite Waterguard . </li></ul><ul><li>Available upon request. </li></ul><ul><li>See engineered detail </li></ul><ul><li>WARNING: The Quick-tab attachment is not to be used at tarped or enclosed scaffolds. </li></ul>*Spacing requirements for application should be determined by a competent scaffold erector or structural engineer per building and safety codes prior to installation . The temporary disconnection and reconnection of this product at erected scaffold should only be performed one connection at a time and only after it is determined safe to do so. The final determination of safety is the sole responsibility of the end user and should be determined by a competent and qualified person. Follow all OSHA, Federal, State, and Local requirements to ensure scaffold safety. To ensure safety, use only components manufactured by Bumperite Waterguards, LLC. at scaffold attachment. Patent Pending
  14. 14. Bumperite Quick-Tab Attachment Illustrations and load Capacity provided by FICCADENTI & WAGGONER , Consulting Structural Engineers, Inc
  15. 15. Manufacturer recommends the use of Densglass Gold exterior sheathing, butyl sealant, Tyvek Straight Flash, minimum UU-B-790a grade D, building paper, and three coat cement plaster per testing report L-06-3059 from Smith-Emery Laboratories, Inc. using test method ASTM E331-00 WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection therewith. RECOMMENDED METHOD OF SEAL AT CONNECTION Patent Pending
  16. 16. Step by Step Patent Pending
  17. 17. Water tested to ASTM E 1105-00 & ASTM E 331-00 by Architectural Testing, Inc. Report No: 90353.01-701-43 WARRANTY: Bumperite Waterguards, LLC. liability expressed or implied is limited to the selling price of any defected goods. User shall determine the suitability of this product for the intended use by doing field test before using, and assumes all risk and liabilities in connection therewith. RECOMMENDED METHOD OF SEAL AT WOOD / STEEL FRAMED ANCHOR PLATE TO EXTERIOR WATER MANAGEMENT SYSTEM Patent Pending
  18. 18. Step by Step at wood / steel framed plates Patent Pending
  19. 19. BUMPERITE - VS - WIRE TIES Testing at Smith-Emery Laboratories suggest that the Bumperite Waterguard peak tension load is MANY TIMES STRONGER than conventional double strand #12 black annealed wire tie assemblies. OSHA 1926.451(c)(1) states, Capacity - - Scaffolds and scaffold components must support at least 4 times the maximum intended load. Sealable & strength Difficult to seal & weaker Patent Pending For More Information Please Contact Us At [email_address] Bumperite Waterguards, LLC. Toll free (877) 490-8884 See Our Web Site At Bumperite.com

×