Successfully reported this slideshow.
Upcoming SlideShare
×

# Instructions of Making Colloidal Silver Using Spooky2

192 views

Published on

http://www.spooky2-mall.com - Follow the following simple steps to create true nano-particle colloidal silver with a high silver content.

Published in: Health & Medicine
• Full Name
Comment goes here.

Are you sure you want to Yes No

• Be the first to like this

### Instructions of Making Colloidal Silver Using Spooky2

1. 1. Spooky2 Instructions of Making Colloidal Silver Using Spooky2 Our Users & Team
2. 2. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com Steps to create true nano-particle colloidal silver: 1. Fill a glass or ceramic container with distilled water. Do not use tap or filtered water. 2. Place two clean and shiny silver rods in the water. They must be more than one inch apart and larger than 14 AWG in thickness – 9 AWG is ideal because the surface area is greater.
3. 3. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com The rods should be at least 99.99% pure silver.
4. 4. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com 3. Making Connection
5. 5. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com 4. Launch Spooky2 and use the calculator to estimate the Dwell you need to enter for the Colloidal Silver Generation program. You may have to go to step 5 and briefly run the generator to measure the Current (mA) with a multimeter so you can enter it in the calculator. The four fields under By Calculation are interactive. Changing a value in one will alter the values in the others. Enter your numbers in the top three to find the Dwell Multiplier you need to enter in the Program Options pane.
6. 6. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com The total time needed to make your CS will be shown beside Duration. The two fields under By Measurement are not interactive. Enter the TDS of your distilled water before you start, then the TDS of the final product (or during production). The Estimated PPM will be shown beneath. Note that a TDS (Total Dissolved Solids) meter will NOT measure the colloidal silver content of a solution. Colloids are not dissolved solids.
7. 7. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com
8. 8. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com If you don't have a multimeter to measure the current, simply make the supposition that your system will consume 0.2 mA. This is a very rough average estimate that assumes you have two 9 AWG rods one inch apart submerged to a depth of 12 inches in distilled water.
9. 9. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com 5. Load the JW-Colloidal Silver Generation Preset and the Colloidal Silver waveform. Enter the estimated dwell into the Dwell Multiplier field and start the Channel. The waveform has been designed to produce very small silver particles of varying size. Do not rush the manufacturing process. Slower is better. Now start your Channel.
10. 10. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com
11. 11. Official Support Website: www.spooky2.com Official Purchasing Website: www.spooky2-mall.com Email:echolee@cleanenergy-npt.com or service@spooky2.com Thank you!