SlideShare a Scribd company logo
INTRODUCTION
A transformer is one of the most common devices found in electrical system that links the
circuits which are operating at different voltages .These are commonly used in applications
where there is a need of AC voltage conversion from one voltage level to another.
It is possible either to decrease or increase the voltage and currents by the use of transformer
in AC circuits based on the requirements of the electrical equipment or device or load. Various
applications use wide variety of transformers including power, instrumentation and pulse
transformers. In a broad, transformers are categorized into two types, namely, electronic
transformers and power transformers. Electronic transformers operating voltages are very low
and are rated at low power levels. These are used in consumer electronic equipments like
televisions, personal computers, CD/DVD players, and other devices.
The term power transformer is referred to the transformers with high power and voltage ratings.
These are extensively used in power generation, transmission, distribution and utility systems
to increase or decrease the voltage levels. However, the operation involved in these two types
of transformers is same. So let us go in detail about the transformers.
WHAT IS AN ELECTRIC TRANSFORMER
A transformer is a static device (means that has no moving parts) that consists of one, two or
more windings which are magnetically coupled and electrically separated with or without a
magnetic core. It transfers the electrical energy from one circuit to the other by electromagnetic
induction principle.
The winding connected to the AC main supply is called primary winding and the winding
connected to the load or from which energy is drawn out is called as secondary winding. These
two windings with proper insulation are wound on a laminated core which provides a magnetic
path between windings.
Electric transformer
When the primary winding is energized with alternating voltage source, an alternating magnetic
flux or field will be produced in the transformer core. This magnetic flux amplitude depends
on the applied voltage magnitude, frequency of the supply and the number of turns on the
primary side.
This flux circulates through the core and hence links with the secondary winding. Based on the
principle of electromagnetic induction, this magnetic linking induces a voltage in the secondary
winding. This is called as mutual induction between two circuits. The secondary voltage
depends on the number of turns on the secondary as well as magnetic flux and frequency.
Transformers are extensively used in electrical power systems to produce the variable values
of voltage and currents at the same frequency. Therefore , by an appropriate primary and
secondary turns proportion desired voltage ratio is obtained by the transformer.
Transformer Construction
The main parts of a transformer are core, windings, container or tank, bushings and
conservator and radiators.
Core
For high power applications, transformer core is made with high permeability material which
provides the low reluctance path for the magnetic flux. The cross section of the core would be
square or rectangular.
Generally the iron core transformers provide better power transformation compared with air
core transformers. Air core transformers are used for high frequency application (above 2
KHz) whereas , for low frequency applications (below 2 KHz) iron core transformers are
employed.
In all types of transformers, core is made up of silicon steel or sheet steel laminations which
are assembled to provide a continuous magnetic path for the flux. With this laminated core
eddy current losses are minimized.
The thickness of these laminated sheets of steel are 0.35 to 5 mm and are insulated with a
varnish, or oxide, or phosphate and then formed as a core.
For a better magnetic properties, Hot rolled grain oriented (HRGO) steel, or Cold Rolled
Grain Oriented (CRGO) steel, or High B (HiB) laminations are used. In case of small
transformers, core is constructed with hot rolled silicon steel laminations in the form of E and
I, C and I or O are used.
Windings
Generally, the (two winding) transformer has two windings namely primary and secondary
windings which are made up of high grade copper.
The insulated stranded conductors are used as windings for carrying high currents. This
insulation avoids turns contacting with other turns.
Windings of a transformer
The voltage connected to the primary winding is called primary voltage whereas the induced
voltage in the secondary is called as secondary voltage. If the secondary voltage is more than
the primary, it is called as step-up transformer and if less, it is called as step-down transformer.
Therefore, the windings are designated as HV and LV windings based on the voltage level.
to the LV winding, HV winding needs more insulation to withstand high voltages, also needs
more clearance to the core and the body.
The transformer coils can be concentric or sandwiched coils. Concentric coils are used in core
type transformers whereas sandwiched coils are used in shell type transformers. In concentric
arrangement, LV winding is placed near to the core and HV winding is placed around the LV
winding for low insulation and clearance requirements. The most commonly used coils for the
transformer include helical, sandwiched, disc and cross over coils.
Other necessary parts of the transformer are conservator tank which is used to provide the
necessary oil storage such that the pressure of the oil under heavy loads settles down. When
the oil in the transformer subject to the heat, naturally, oil expand and contract. Under this, oil
is subjected to heavy pressure so without a conservator tank, there will be a chance of bursting
the transformer.
The bushings provide the insulation to the output terminals to be taken from the windings of
the transformer. These can be porcelain or condenser type bushing and based on the level of
operating voltage these are selected. Because of simple, durable and rugged construction,
transformers require a little maintenance. Because of no moving parts, the efficiency of the
transformer is very high which may vary from 95% to 98%.
ClassificationofTransformers
Transformers are classified into several types depends the various factors including voltage
ratings, construction, type of cooling, number of phases of the AC system, the place where it
is employed, etc. Let us discuss some of these types of transformers.
Basedon Function
Transformers are classified into two types based on the conversion of voltage level. These are
step-up and step-down transformers.
Step-up Transformers
In step-up transformer, the secondary voltage is more than the primary voltage. This is due to
the lesser number of coils in the primary compared to the secondary. This type of transformer
is used to raise the voltage to a higher level. These are used in transmission systems and are
rated at higher power levels.
Step-down Transformers
In step-down transformer, secondary voltage is less than the primary voltage due to the less
number of turns in the secondary winding. Hence, this type of transformer is used to reduce the
voltage to specified levels of the circuit. Most of the power supplies use the step-down
transformer to keep the circuit operating range to a specified safer voltage limit. These types
of transformers are used in distribution systems (power transformers) and in electronic circuits
(electronic transformers).
It is to be noted that the transformer is a reversible device, so it can be used as both step-up and
step-down transformer. For example, if the circuit needs a high voltage we will connect the HV
terminals to the load whereas the load or circuit needs a low voltage, we will connect the LV
terminals to the load The ratio of the voltage of a transformer is determined by the turns ratio.
With the use of larger number of turns in the winding, higher will be the voltage produced in
it. Hence, a step down transformer has lesser number of turns on secondary to produce a low
voltage and has more turns on primary to withstand high voltage levels of the AC supply.
Turns Ratio = Primary Voltage/ Secondary Voltage = Primary Turns/ Secondary turns
The turns ratio is, VP /VS = NP /NS
Based on Core Construction
Based on the construction, transformers are classified into two types in the manner in which
the windings are placed around the core. These types are core and shell type transformers.
Core Type transformer
Core type transformer
In this type of transformer, windings surround the considerable part of the core. Generally,
distribution transformers are of core type. Some of the large power transformers are of shell
type Form-wound, cylindrical coils are used in the core type transformers and these coils may
be rectangular, or oval, or circular. For small size core type transformer, a simple rectangular
core with a cylindrical coil in either circular or rectangular form is used.
And for a large sized core type transformer, cruciform core with round or circular cylindrical
coils are used. In most of the core type transformers, cylindrical coils are used due to their
mechanical strength. These cylindrical coils are wound in helical layers and are insulated from
each other by insulating materials like cloth, paper, mica, etc.
It is easy to insulate the LV winding compared to the HV winding; hence it is placed nearer to
the core.
Shell Type Transformer
In a shell type transformer, iron core surrounds a considerable portion of the copper winding
as a reverse case to the core type transformer. In this type also, coils are former wound, but are
of multilayer disc type coils which are wounded in the form of pancakes. These multilayer disc
coils in different layers of are separated each other by paper. The whole winding consists of
stacked discs and in between the coils the insulation space is provided to form the horizontal
insulating and cooling ducts.
Berry transformer is the most commonly used shell type transformer. In shell type, core has
three limbs and the windings are wound around the central limb. Both LV and HV windings
are divided into different coils which are arranged alternately. Between the LV windings, HV
windings are sandwiched. Again to reduce the insulation requirement, LV windings are placed
adjacent to the core. This type of construction is preferred for high rating transformers.
Shell type transformer
Basedon Nature of Supply
Based on the nature of the supply, transformers can be single or three phase transformers.
Single phase transformers are designed to work on a single phase system; therefore it has two
windings to transform the voltage levels. These are used in remote ends of the power
distribution system. These have less power rating compared with three phase transformers.
Mostly core type construction is used for this type of transformer.
To work with three phase system, we need three single phase transformers. Thus, for an
economic advantage, three phase transformer is considered for three phase operation. It
consists of three windings or coils which are connected in a proper way to match the input
voltage. This type of transformers, primary and secondary windings are connected in the
form of star- delta or delta-star fashion depending on the load voltage requirements
Basedon Use
1.Power transformer
2.Distribution transformer
3.Instrument transformer
Other Types of Transformer
Based on the type of cooling these are classified into
1.Self air cooled transformer
2.Air blast cooled transformer
3.Oil filled self cooled transformer
4.Oil filled water cooled transformer
5.Oil filled forced oil cooled transformer
Working Principle of Transformer
The operation of the transformer is based on the principle of mutual induction between two
coils or winding which are linked by a common magnetic flux. When the primary winding is
energized with AC source supply, a magnetic flux is established in the primary winding.
This flux is linked with both primary and secondary windings because the core provides a low
reluctance path for the magnetic flux. Hence, most of the flux produced by the primary winding
links with the secondary winding. This is called as main flux or useful flux. And also, the flux
which does not link with the secondary winding is called as leakage flux. Most of the
transformers are designed to have low leakage flux to reduce the losses.
According to the Faraday’s laws of electromagnetic induction, this flux linkage with both
primary and secondary windings induces EMFs in them. This EMF induced in each winding is
proportional to the number of turns in it. The voltage or EMF induced in the primary winding
is called as back EMF which opposes the input supply voltage to the extent that no primary
current would flow.
But small magnetizing current flows through the primary of the transformer. The EMF induced
in the secondary winding is the open circuit voltage. If the secondary circuit is closed or the
load is connected, secondary current starts flowing through it which causes to create
demagnetizing magnetic flux. Due to this demagnetizing flux, the unbalance is created between
the applied voltage and back EMF.
To restore the balance between these two, more current is drawn from the supply source so that
equivalent magnetic field is created to balance with secondary field.
Principle of operation
Since the same mutual flux cuts both windings, the EMF induced in the each turn of both
windings are same. Hence the total induced EMF in each winding must be proportional to the
number of turns in that winding. This turns out for the establishment of well-known relationship
between induced EMF and the number of turns. And is given as
E1 /E2 = N1 / N2
Since the terminal voltages of the both windings are slightly different from their induced EMFs,
we can write as
V1/V2 = N1/N2
This is called as the transformation ratio of the transformer. This transformation value is greater
than unity in case of step-up transformer and less than unity in step-down transformer.
In terms of ampere turns balance,
I1N1 = I2N2
I1/I2 = N2/N1
Losses in Transformer
The transformer has no moving parts and hence the mechanical losses are absent in it. Hence,
the losses in the transformer are considered as electrical energy losses. Two types of
electrical losses are exist in a transformer which are core losses and copper losses.
Core or Iron Losses
These losses include both hysteresis and eddy current losses.
The magnetic flux set up in the transformer core is alternating type; thereby it undergoes a
cycle of magnetization and demagnetization. During this, an appropriate power is required for
continuous reversal of elementary magnets of the iron core. This is called as hysteresis effect
and due to this considerable loss of energy takes place.
Hysteresis loss = Kh Bm1.67f v Watts
Where,
Kh = Hysteresis Constant
Bm = Maximum flux density
F= frequency
V = volume of the core
Since the transformer core is made up of ferromagnetic materials that are also good conductors.
And hence, the magnetic flux linking with core induces emf in the core. Hence the core set up
eddy currents in the core, thereby considerable eddy current losses occurs in the core.
Eddy Current losses = Ke Bm2f2t2 W/unit volume
Where,
Ke = Eddy current constant
T = thickness of the core
From the above two equations, it is to be observed that the supply voltage at a fixed frequency
is constant and hence the flux in turn flux density in the core is almost constant. Therefore,
both hysteresis and eddy current losses are constant during all loads. Hence the core losses are
also called as constant losses.
By using the high grade core materials like silicon steel having very low hysteresis loop,
hysteresis losses are minimized or reduced. On other hand, eddy current losses are minimized
by using laminated core. These constant or core losses can be measured by conducting an open
circuit on the transformer.
Copper Losses
These losses occur in the winding resistances of the transformer when it carries load current.
The total copper loss in the transformer is obtained by adding both primary and secondary
copper losses. These are found by conducting short circuit rest on the transformer.
Applications of Transformers
 Step-up or step-down the level of the voltage in power transmission systems like
transmission and distribution systems.
 To isolate the low voltage circuits from high voltage circuits in case of substations,
control circuitry circuits in industries, etc.
 Instrument transformers like current and potential transformer are used in protection
and meter indication systems.
 These are also used for impedance matching.
CONCLUSION:- The method could possibly used for the transfer of electricity
across the country via the power lines. The circuit was not supplying the most efficient or
increases the voltage out, then the current out must decreases.

More Related Content

What's hot

Transformer Parts and functions
Transformer Parts and functionsTransformer Parts and functions
Transformer Parts and functions
Sourabh sharma
 
Instrument transformer CT & PT
Instrument transformer CT & PTInstrument transformer CT & PT
Instrument transformer CT & PT
Chandan Singh
 
Ppt on protection of power transformers
Ppt on protection of power transformersPpt on protection of power transformers
Ppt on protection of power transformers
siddharam kantoli
 
Tap changer
Tap changerTap changer
Tap changer
vivek1292
 
construction, types and working principle of single phase transformer
construction, types and working principle of single phase transformerconstruction, types and working principle of single phase transformer
construction, types and working principle of single phase transformer
Arunkumar Tulasi
 
Differential Protection Relay
DifferentialProtection RelayDifferentialProtection Relay
Differential Protection Relay
kishore kish
 
Parallel Inverter
Parallel InverterParallel Inverter
Parallel Inverter
Smit Shah
 
Protection Of Generator
Protection Of GeneratorProtection Of Generator
Protection Of Generator
Rahuldey1991
 
Power Electronics 2 mark Questions
Power Electronics 2 mark Questions Power Electronics 2 mark Questions
Power Electronics 2 mark Questions
BALACHANDRAN D
 
Transformer basics
Transformer   basicsTransformer   basics
Transformer basics
AtheenaPandian Enterprises
 
Capacitive voltage transformer (1)
Capacitive voltage transformer (1)Capacitive voltage transformer (1)
Capacitive voltage transformer (1)
kaushal boghani
 
Protection & switchgear
Protection & switchgear   Protection & switchgear
Protection & switchgear
johny renoald
 
Transient in Power system
Transient in Power systemTransient in Power system
Transient in Power system
Preet_patel
 
Over current protection
Over current protectionOver current protection
Over current protection
SHUBHAM KUMAR
 
Transformer
TransformerTransformer
Dc Choppers
Dc ChoppersDc Choppers
Dc Choppers
stooty s
 
Three phase voltage source inverter
Three phase voltage source inverterThree phase voltage source inverter
Three phase voltage source inverter
tamilnesaner
 
Protection of transmission lines (distance)
Protection of transmission lines (distance)Protection of transmission lines (distance)
Protection of transmission lines (distance)
Rohini Haridas
 
Inverter
InverterInverter
Inverter
Somu Gupta
 
Transformer Repair Workshop Report [EEE]
Transformer Repair Workshop Report [EEE] Transformer Repair Workshop Report [EEE]
Transformer Repair Workshop Report [EEE]
Nik Sharma
 

What's hot (20)

Transformer Parts and functions
Transformer Parts and functionsTransformer Parts and functions
Transformer Parts and functions
 
Instrument transformer CT & PT
Instrument transformer CT & PTInstrument transformer CT & PT
Instrument transformer CT & PT
 
Ppt on protection of power transformers
Ppt on protection of power transformersPpt on protection of power transformers
Ppt on protection of power transformers
 
Tap changer
Tap changerTap changer
Tap changer
 
construction, types and working principle of single phase transformer
construction, types and working principle of single phase transformerconstruction, types and working principle of single phase transformer
construction, types and working principle of single phase transformer
 
Differential Protection Relay
DifferentialProtection RelayDifferentialProtection Relay
Differential Protection Relay
 
Parallel Inverter
Parallel InverterParallel Inverter
Parallel Inverter
 
Protection Of Generator
Protection Of GeneratorProtection Of Generator
Protection Of Generator
 
Power Electronics 2 mark Questions
Power Electronics 2 mark Questions Power Electronics 2 mark Questions
Power Electronics 2 mark Questions
 
Transformer basics
Transformer   basicsTransformer   basics
Transformer basics
 
Capacitive voltage transformer (1)
Capacitive voltage transformer (1)Capacitive voltage transformer (1)
Capacitive voltage transformer (1)
 
Protection & switchgear
Protection & switchgear   Protection & switchgear
Protection & switchgear
 
Transient in Power system
Transient in Power systemTransient in Power system
Transient in Power system
 
Over current protection
Over current protectionOver current protection
Over current protection
 
Transformer
TransformerTransformer
Transformer
 
Dc Choppers
Dc ChoppersDc Choppers
Dc Choppers
 
Three phase voltage source inverter
Three phase voltage source inverterThree phase voltage source inverter
Three phase voltage source inverter
 
Protection of transmission lines (distance)
Protection of transmission lines (distance)Protection of transmission lines (distance)
Protection of transmission lines (distance)
 
Inverter
InverterInverter
Inverter
 
Transformer Repair Workshop Report [EEE]
Transformer Repair Workshop Report [EEE] Transformer Repair Workshop Report [EEE]
Transformer Repair Workshop Report [EEE]
 

Similar to Presentation report of transformer

power transforer.pptx
power transforer.pptxpower transforer.pptx
power transforer.pptx
Avanishkumarshrivast1
 
Distribution transformer
Distribution transformerDistribution transformer
Distribution transformer
Engr Muhammad Imran
 
TRANSFORMER.pptx
TRANSFORMER.pptxTRANSFORMER.pptx
TRANSFORMER.pptx
Yogita Janghu
 
Transformer types
Transformer typesTransformer types
Transformer types
elprocus
 
University college of engineering, rajasthan technical university
University college of engineering, rajasthan technical universityUniversity college of engineering, rajasthan technical university
University college of engineering, rajasthan technical university
Divyansh Gupta
 
transformer and app.pptxvdgvbffhgfhhtghh
transformer and app.pptxvdgvbffhgfhhtghhtransformer and app.pptxvdgvbffhgfhhtghh
transformer and app.pptxvdgvbffhgfhhtghh
saravananr517913
 
Transformers (ee)
Transformers (ee)Transformers (ee)
Transformers (ee)
KARAN SHARMA
 
Distribution transformer
Distribution transformerDistribution transformer
Distribution transformer
Muhammad Mohsin Raza
 
OPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.ppt
OPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.pptOPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.ppt
OPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.ppt
MadavanR1
 
transformer ppt
transformer ppttransformer ppt
transformer ppt
Sharukh Ansari
 
Presentation about transformer and its types
Presentation about transformer and its types Presentation about transformer and its types
Presentation about transformer and its types
M Tahir Shaheen
 
Kings Transformer types
Kings  Transformer typesKings  Transformer types
Kings Transformer types
Parmeshwar Pawar
 
Transformers
TransformersTransformers
Transformers
SoumyaRanjanDas13
 
Chapter#32
Chapter#32Chapter#32
TRANSFORMERS.pptx
TRANSFORMERS.pptxTRANSFORMERS.pptx
TRANSFORMERS.pptx
roshan375533
 
Transformer, it's types and cooling methods with power factor, percentage imp...
Transformer, it's types and cooling methods with power factor, percentage imp...Transformer, it's types and cooling methods with power factor, percentage imp...
Transformer, it's types and cooling methods with power factor, percentage imp...
Urooj Abid
 
Presentation on Transformer.pptx
Presentation on Transformer.pptxPresentation on Transformer.pptx
Presentation on Transformer.pptx
UshaBharathiSb
 
Transformer by Hemant
Transformer by HemantTransformer by Hemant
Transformer by Hemant
HemantChoudhary65
 
G1-Distri-Transformer.pptx
G1-Distri-Transformer.pptxG1-Distri-Transformer.pptx
G1-Distri-Transformer.pptx
marcoogsilaverdera
 
Transformers and its Types
Transformers and its TypesTransformers and its Types
Transformers and its Types
PRANAV287309
 

Similar to Presentation report of transformer (20)

power transforer.pptx
power transforer.pptxpower transforer.pptx
power transforer.pptx
 
Distribution transformer
Distribution transformerDistribution transformer
Distribution transformer
 
TRANSFORMER.pptx
TRANSFORMER.pptxTRANSFORMER.pptx
TRANSFORMER.pptx
 
Transformer types
Transformer typesTransformer types
Transformer types
 
University college of engineering, rajasthan technical university
University college of engineering, rajasthan technical universityUniversity college of engineering, rajasthan technical university
University college of engineering, rajasthan technical university
 
transformer and app.pptxvdgvbffhgfhhtghh
transformer and app.pptxvdgvbffhgfhhtghhtransformer and app.pptxvdgvbffhgfhhtghh
transformer and app.pptxvdgvbffhgfhhtghh
 
Transformers (ee)
Transformers (ee)Transformers (ee)
Transformers (ee)
 
Distribution transformer
Distribution transformerDistribution transformer
Distribution transformer
 
OPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.ppt
OPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.pptOPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.ppt
OPERATING PRINCIPLES OF TRANSFORMER AND CONSTRUCTION.ppt
 
transformer ppt
transformer ppttransformer ppt
transformer ppt
 
Presentation about transformer and its types
Presentation about transformer and its types Presentation about transformer and its types
Presentation about transformer and its types
 
Kings Transformer types
Kings  Transformer typesKings  Transformer types
Kings Transformer types
 
Transformers
TransformersTransformers
Transformers
 
Chapter#32
Chapter#32Chapter#32
Chapter#32
 
TRANSFORMERS.pptx
TRANSFORMERS.pptxTRANSFORMERS.pptx
TRANSFORMERS.pptx
 
Transformer, it's types and cooling methods with power factor, percentage imp...
Transformer, it's types and cooling methods with power factor, percentage imp...Transformer, it's types and cooling methods with power factor, percentage imp...
Transformer, it's types and cooling methods with power factor, percentage imp...
 
Presentation on Transformer.pptx
Presentation on Transformer.pptxPresentation on Transformer.pptx
Presentation on Transformer.pptx
 
Transformer by Hemant
Transformer by HemantTransformer by Hemant
Transformer by Hemant
 
G1-Distri-Transformer.pptx
G1-Distri-Transformer.pptxG1-Distri-Transformer.pptx
G1-Distri-Transformer.pptx
 
Transformers and its Types
Transformers and its TypesTransformers and its Types
Transformers and its Types
 

Recently uploaded

Online airline reservation system project report.pdf
Online airline reservation system project report.pdfOnline airline reservation system project report.pdf
Online airline reservation system project report.pdf
Kamal Acharya
 
The world of Technology Management MEM 814.pptx
The world of Technology Management MEM 814.pptxThe world of Technology Management MEM 814.pptx
The world of Technology Management MEM 814.pptx
engrasjadshahzad
 
Ludo system project report management .pdf
Ludo  system project report management .pdfLudo  system project report management .pdf
Ludo system project report management .pdf
Kamal Acharya
 
SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...
SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...
SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...
Jim Mimlitz, P.E.
 
Girls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in City
Girls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in CityGirls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in City
Girls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in City
rawankhanlove256
 
Metrology Book, Bachelors in Mechanical Engineering
Metrology Book, Bachelors in Mechanical EngineeringMetrology Book, Bachelors in Mechanical Engineering
Metrology Book, Bachelors in Mechanical Engineering
leakingvideo
 
readers writers Problem in operating system
readers writers Problem in operating systemreaders writers Problem in operating system
readers writers Problem in operating system
VADAPALLYPRAVEENKUMA1
 
李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<
李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<
李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<
amzhoxvzidbke
 
Distillation-1.vapour liquid equilibrium
Distillation-1.vapour liquid equilibriumDistillation-1.vapour liquid equilibrium
Distillation-1.vapour liquid equilibrium
RjKing12
 
API-1150WB-Cooling Towers.pdf with details
API-1150WB-Cooling Towers.pdf with detailsAPI-1150WB-Cooling Towers.pdf with details
API-1150WB-Cooling Towers.pdf with details
MuhammadUsmanAsghar4
 
Introduction And Differences Between File System And Dbms.pptx
Introduction And Differences Between File System And Dbms.pptxIntroduction And Differences Between File System And Dbms.pptx
Introduction And Differences Between File System And Dbms.pptx
SerendipityYoon
 
Disaster Management and Mitigation presentation
Disaster Management and Mitigation presentationDisaster Management and Mitigation presentation
Disaster Management and Mitigation presentation
RajaRamannaTarigoppu
 
Presentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptx
Presentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptxPresentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptx
Presentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptx
Er. Kushal Ghimire
 
ISO 9001 - 2015 Quality Management Awareness.pdf
ISO 9001 - 2015 Quality Management Awareness.pdfISO 9001 - 2015 Quality Management Awareness.pdf
ISO 9001 - 2015 Quality Management Awareness.pdf
InfoDqms
 
FINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATA
FINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATAFINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATA
FINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATA
kevig
 
Tutorial on MySQl and its basic concepts
Tutorial on MySQl and its basic conceptsTutorial on MySQl and its basic concepts
Tutorial on MySQl and its basic concepts
anishacotta2
 
Buy a fake University of Washington diploma
Buy a fake University of Washington diplomaBuy a fake University of Washington diploma
Buy a fake University of Washington diploma
College diploma
 
Generative-AI-a-boost-for-operations-Presentation.pdf
Generative-AI-a-boost-for-operations-Presentation.pdfGenerative-AI-a-boost-for-operations-Presentation.pdf
Generative-AI-a-boost-for-operations-Presentation.pdf
Aries716858
 
ANATOMY OF SOA - Thomas Erl - Service Oriented Architecture
ANATOMY OF SOA - Thomas Erl - Service Oriented ArchitectureANATOMY OF SOA - Thomas Erl - Service Oriented Architecture
ANATOMY OF SOA - Thomas Erl - Service Oriented Architecture
Divya Rajasekar
 
The Control of Relative Humidity & Moisture Content in The Air
The Control of Relative Humidity & Moisture Content in The AirThe Control of Relative Humidity & Moisture Content in The Air
The Control of Relative Humidity & Moisture Content in The Air
Ashraf Ismail
 

Recently uploaded (20)

Online airline reservation system project report.pdf
Online airline reservation system project report.pdfOnline airline reservation system project report.pdf
Online airline reservation system project report.pdf
 
The world of Technology Management MEM 814.pptx
The world of Technology Management MEM 814.pptxThe world of Technology Management MEM 814.pptx
The world of Technology Management MEM 814.pptx
 
Ludo system project report management .pdf
Ludo  system project report management .pdfLudo  system project report management .pdf
Ludo system project report management .pdf
 
SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...
SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...
SCADAmetrics Instrumentation for Sensus Water Meters - Core and Main Training...
 
Girls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in City
Girls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in CityGirls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in City
Girls Call Mysore 000XX00000 Provide Best And Top Girl Service And No1 in City
 
Metrology Book, Bachelors in Mechanical Engineering
Metrology Book, Bachelors in Mechanical EngineeringMetrology Book, Bachelors in Mechanical Engineering
Metrology Book, Bachelors in Mechanical Engineering
 
readers writers Problem in operating system
readers writers Problem in operating systemreaders writers Problem in operating system
readers writers Problem in operating system
 
李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<
李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<
李易峰祝绪丹做爱视频流出【网芷:ht28.co】可爱学生妹>>>[网趾:ht28.co】]<<<
 
Distillation-1.vapour liquid equilibrium
Distillation-1.vapour liquid equilibriumDistillation-1.vapour liquid equilibrium
Distillation-1.vapour liquid equilibrium
 
API-1150WB-Cooling Towers.pdf with details
API-1150WB-Cooling Towers.pdf with detailsAPI-1150WB-Cooling Towers.pdf with details
API-1150WB-Cooling Towers.pdf with details
 
Introduction And Differences Between File System And Dbms.pptx
Introduction And Differences Between File System And Dbms.pptxIntroduction And Differences Between File System And Dbms.pptx
Introduction And Differences Between File System And Dbms.pptx
 
Disaster Management and Mitigation presentation
Disaster Management and Mitigation presentationDisaster Management and Mitigation presentation
Disaster Management and Mitigation presentation
 
Presentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptx
Presentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptxPresentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptx
Presentation slide on DESIGN AND FABRICATION OF MOBILE CONTROLLED DRAINAGE.pptx
 
ISO 9001 - 2015 Quality Management Awareness.pdf
ISO 9001 - 2015 Quality Management Awareness.pdfISO 9001 - 2015 Quality Management Awareness.pdf
ISO 9001 - 2015 Quality Management Awareness.pdf
 
FINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATA
FINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATAFINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATA
FINE-TUNING OF SMALL/MEDIUM LLMS FOR BUSINESS QA ON STRUCTURED DATA
 
Tutorial on MySQl and its basic concepts
Tutorial on MySQl and its basic conceptsTutorial on MySQl and its basic concepts
Tutorial on MySQl and its basic concepts
 
Buy a fake University of Washington diploma
Buy a fake University of Washington diplomaBuy a fake University of Washington diploma
Buy a fake University of Washington diploma
 
Generative-AI-a-boost-for-operations-Presentation.pdf
Generative-AI-a-boost-for-operations-Presentation.pdfGenerative-AI-a-boost-for-operations-Presentation.pdf
Generative-AI-a-boost-for-operations-Presentation.pdf
 
ANATOMY OF SOA - Thomas Erl - Service Oriented Architecture
ANATOMY OF SOA - Thomas Erl - Service Oriented ArchitectureANATOMY OF SOA - Thomas Erl - Service Oriented Architecture
ANATOMY OF SOA - Thomas Erl - Service Oriented Architecture
 
The Control of Relative Humidity & Moisture Content in The Air
The Control of Relative Humidity & Moisture Content in The AirThe Control of Relative Humidity & Moisture Content in The Air
The Control of Relative Humidity & Moisture Content in The Air
 

Presentation report of transformer

  • 1. INTRODUCTION A transformer is one of the most common devices found in electrical system that links the circuits which are operating at different voltages .These are commonly used in applications where there is a need of AC voltage conversion from one voltage level to another. It is possible either to decrease or increase the voltage and currents by the use of transformer in AC circuits based on the requirements of the electrical equipment or device or load. Various applications use wide variety of transformers including power, instrumentation and pulse transformers. In a broad, transformers are categorized into two types, namely, electronic transformers and power transformers. Electronic transformers operating voltages are very low and are rated at low power levels. These are used in consumer electronic equipments like televisions, personal computers, CD/DVD players, and other devices. The term power transformer is referred to the transformers with high power and voltage ratings. These are extensively used in power generation, transmission, distribution and utility systems to increase or decrease the voltage levels. However, the operation involved in these two types of transformers is same. So let us go in detail about the transformers.
  • 2. WHAT IS AN ELECTRIC TRANSFORMER A transformer is a static device (means that has no moving parts) that consists of one, two or more windings which are magnetically coupled and electrically separated with or without a magnetic core. It transfers the electrical energy from one circuit to the other by electromagnetic induction principle. The winding connected to the AC main supply is called primary winding and the winding connected to the load or from which energy is drawn out is called as secondary winding. These two windings with proper insulation are wound on a laminated core which provides a magnetic path between windings. Electric transformer When the primary winding is energized with alternating voltage source, an alternating magnetic flux or field will be produced in the transformer core. This magnetic flux amplitude depends on the applied voltage magnitude, frequency of the supply and the number of turns on the primary side.
  • 3. This flux circulates through the core and hence links with the secondary winding. Based on the principle of electromagnetic induction, this magnetic linking induces a voltage in the secondary winding. This is called as mutual induction between two circuits. The secondary voltage depends on the number of turns on the secondary as well as magnetic flux and frequency. Transformers are extensively used in electrical power systems to produce the variable values of voltage and currents at the same frequency. Therefore , by an appropriate primary and secondary turns proportion desired voltage ratio is obtained by the transformer. Transformer Construction The main parts of a transformer are core, windings, container or tank, bushings and conservator and radiators. Core For high power applications, transformer core is made with high permeability material which provides the low reluctance path for the magnetic flux. The cross section of the core would be square or rectangular. Generally the iron core transformers provide better power transformation compared with air core transformers. Air core transformers are used for high frequency application (above 2 KHz) whereas , for low frequency applications (below 2 KHz) iron core transformers are employed. In all types of transformers, core is made up of silicon steel or sheet steel laminations which are assembled to provide a continuous magnetic path for the flux. With this laminated core eddy current losses are minimized. The thickness of these laminated sheets of steel are 0.35 to 5 mm and are insulated with a varnish, or oxide, or phosphate and then formed as a core. For a better magnetic properties, Hot rolled grain oriented (HRGO) steel, or Cold Rolled Grain Oriented (CRGO) steel, or High B (HiB) laminations are used. In case of small transformers, core is constructed with hot rolled silicon steel laminations in the form of E and I, C and I or O are used. Windings
  • 4. Generally, the (two winding) transformer has two windings namely primary and secondary windings which are made up of high grade copper. The insulated stranded conductors are used as windings for carrying high currents. This insulation avoids turns contacting with other turns. Windings of a transformer
  • 5. The voltage connected to the primary winding is called primary voltage whereas the induced voltage in the secondary is called as secondary voltage. If the secondary voltage is more than the primary, it is called as step-up transformer and if less, it is called as step-down transformer. Therefore, the windings are designated as HV and LV windings based on the voltage level. to the LV winding, HV winding needs more insulation to withstand high voltages, also needs more clearance to the core and the body. The transformer coils can be concentric or sandwiched coils. Concentric coils are used in core type transformers whereas sandwiched coils are used in shell type transformers. In concentric arrangement, LV winding is placed near to the core and HV winding is placed around the LV winding for low insulation and clearance requirements. The most commonly used coils for the transformer include helical, sandwiched, disc and cross over coils. Other necessary parts of the transformer are conservator tank which is used to provide the necessary oil storage such that the pressure of the oil under heavy loads settles down. When the oil in the transformer subject to the heat, naturally, oil expand and contract. Under this, oil is subjected to heavy pressure so without a conservator tank, there will be a chance of bursting the transformer. The bushings provide the insulation to the output terminals to be taken from the windings of the transformer. These can be porcelain or condenser type bushing and based on the level of operating voltage these are selected. Because of simple, durable and rugged construction, transformers require a little maintenance. Because of no moving parts, the efficiency of the transformer is very high which may vary from 95% to 98%. ClassificationofTransformers Transformers are classified into several types depends the various factors including voltage ratings, construction, type of cooling, number of phases of the AC system, the place where it is employed, etc. Let us discuss some of these types of transformers. Basedon Function Transformers are classified into two types based on the conversion of voltage level. These are step-up and step-down transformers.
  • 6. Step-up Transformers In step-up transformer, the secondary voltage is more than the primary voltage. This is due to the lesser number of coils in the primary compared to the secondary. This type of transformer is used to raise the voltage to a higher level. These are used in transmission systems and are rated at higher power levels. Step-down Transformers In step-down transformer, secondary voltage is less than the primary voltage due to the less number of turns in the secondary winding. Hence, this type of transformer is used to reduce the voltage to specified levels of the circuit. Most of the power supplies use the step-down transformer to keep the circuit operating range to a specified safer voltage limit. These types of transformers are used in distribution systems (power transformers) and in electronic circuits (electronic transformers). It is to be noted that the transformer is a reversible device, so it can be used as both step-up and step-down transformer. For example, if the circuit needs a high voltage we will connect the HV terminals to the load whereas the load or circuit needs a low voltage, we will connect the LV terminals to the load The ratio of the voltage of a transformer is determined by the turns ratio. With the use of larger number of turns in the winding, higher will be the voltage produced in it. Hence, a step down transformer has lesser number of turns on secondary to produce a low voltage and has more turns on primary to withstand high voltage levels of the AC supply.
  • 7. Turns Ratio = Primary Voltage/ Secondary Voltage = Primary Turns/ Secondary turns The turns ratio is, VP /VS = NP /NS
  • 8. Based on Core Construction Based on the construction, transformers are classified into two types in the manner in which the windings are placed around the core. These types are core and shell type transformers. Core Type transformer Core type transformer In this type of transformer, windings surround the considerable part of the core. Generally, distribution transformers are of core type. Some of the large power transformers are of shell type Form-wound, cylindrical coils are used in the core type transformers and these coils may be rectangular, or oval, or circular. For small size core type transformer, a simple rectangular core with a cylindrical coil in either circular or rectangular form is used. And for a large sized core type transformer, cruciform core with round or circular cylindrical coils are used. In most of the core type transformers, cylindrical coils are used due to their mechanical strength. These cylindrical coils are wound in helical layers and are insulated from each other by insulating materials like cloth, paper, mica, etc. It is easy to insulate the LV winding compared to the HV winding; hence it is placed nearer to the core.
  • 9. Shell Type Transformer In a shell type transformer, iron core surrounds a considerable portion of the copper winding as a reverse case to the core type transformer. In this type also, coils are former wound, but are of multilayer disc type coils which are wounded in the form of pancakes. These multilayer disc coils in different layers of are separated each other by paper. The whole winding consists of stacked discs and in between the coils the insulation space is provided to form the horizontal insulating and cooling ducts. Berry transformer is the most commonly used shell type transformer. In shell type, core has three limbs and the windings are wound around the central limb. Both LV and HV windings are divided into different coils which are arranged alternately. Between the LV windings, HV windings are sandwiched. Again to reduce the insulation requirement, LV windings are placed adjacent to the core. This type of construction is preferred for high rating transformers. Shell type transformer Basedon Nature of Supply Based on the nature of the supply, transformers can be single or three phase transformers. Single phase transformers are designed to work on a single phase system; therefore it has two
  • 10. windings to transform the voltage levels. These are used in remote ends of the power distribution system. These have less power rating compared with three phase transformers. Mostly core type construction is used for this type of transformer. To work with three phase system, we need three single phase transformers. Thus, for an economic advantage, three phase transformer is considered for three phase operation. It consists of three windings or coils which are connected in a proper way to match the input voltage. This type of transformers, primary and secondary windings are connected in the form of star- delta or delta-star fashion depending on the load voltage requirements Basedon Use 1.Power transformer 2.Distribution transformer 3.Instrument transformer
  • 11. Other Types of Transformer Based on the type of cooling these are classified into 1.Self air cooled transformer 2.Air blast cooled transformer 3.Oil filled self cooled transformer 4.Oil filled water cooled transformer 5.Oil filled forced oil cooled transformer
  • 12. Working Principle of Transformer The operation of the transformer is based on the principle of mutual induction between two coils or winding which are linked by a common magnetic flux. When the primary winding is energized with AC source supply, a magnetic flux is established in the primary winding. This flux is linked with both primary and secondary windings because the core provides a low reluctance path for the magnetic flux. Hence, most of the flux produced by the primary winding links with the secondary winding. This is called as main flux or useful flux. And also, the flux which does not link with the secondary winding is called as leakage flux. Most of the transformers are designed to have low leakage flux to reduce the losses. According to the Faraday’s laws of electromagnetic induction, this flux linkage with both primary and secondary windings induces EMFs in them. This EMF induced in each winding is proportional to the number of turns in it. The voltage or EMF induced in the primary winding is called as back EMF which opposes the input supply voltage to the extent that no primary current would flow. But small magnetizing current flows through the primary of the transformer. The EMF induced in the secondary winding is the open circuit voltage. If the secondary circuit is closed or the load is connected, secondary current starts flowing through it which causes to create demagnetizing magnetic flux. Due to this demagnetizing flux, the unbalance is created between the applied voltage and back EMF. To restore the balance between these two, more current is drawn from the supply source so that equivalent magnetic field is created to balance with secondary field. Principle of operation
  • 13. Since the same mutual flux cuts both windings, the EMF induced in the each turn of both windings are same. Hence the total induced EMF in each winding must be proportional to the number of turns in that winding. This turns out for the establishment of well-known relationship between induced EMF and the number of turns. And is given as E1 /E2 = N1 / N2 Since the terminal voltages of the both windings are slightly different from their induced EMFs, we can write as V1/V2 = N1/N2 This is called as the transformation ratio of the transformer. This transformation value is greater than unity in case of step-up transformer and less than unity in step-down transformer. In terms of ampere turns balance, I1N1 = I2N2 I1/I2 = N2/N1
  • 14. Losses in Transformer The transformer has no moving parts and hence the mechanical losses are absent in it. Hence, the losses in the transformer are considered as electrical energy losses. Two types of electrical losses are exist in a transformer which are core losses and copper losses. Core or Iron Losses These losses include both hysteresis and eddy current losses. The magnetic flux set up in the transformer core is alternating type; thereby it undergoes a cycle of magnetization and demagnetization. During this, an appropriate power is required for continuous reversal of elementary magnets of the iron core. This is called as hysteresis effect and due to this considerable loss of energy takes place. Hysteresis loss = Kh Bm1.67f v Watts Where, Kh = Hysteresis Constant Bm = Maximum flux density F= frequency V = volume of the core Since the transformer core is made up of ferromagnetic materials that are also good conductors. And hence, the magnetic flux linking with core induces emf in the core. Hence the core set up eddy currents in the core, thereby considerable eddy current losses occurs in the core. Eddy Current losses = Ke Bm2f2t2 W/unit volume Where,
  • 15. Ke = Eddy current constant T = thickness of the core From the above two equations, it is to be observed that the supply voltage at a fixed frequency is constant and hence the flux in turn flux density in the core is almost constant. Therefore, both hysteresis and eddy current losses are constant during all loads. Hence the core losses are also called as constant losses. By using the high grade core materials like silicon steel having very low hysteresis loop, hysteresis losses are minimized or reduced. On other hand, eddy current losses are minimized by using laminated core. These constant or core losses can be measured by conducting an open circuit on the transformer. Copper Losses These losses occur in the winding resistances of the transformer when it carries load current. The total copper loss in the transformer is obtained by adding both primary and secondary copper losses. These are found by conducting short circuit rest on the transformer.
  • 16. Applications of Transformers  Step-up or step-down the level of the voltage in power transmission systems like transmission and distribution systems.  To isolate the low voltage circuits from high voltage circuits in case of substations, control circuitry circuits in industries, etc.  Instrument transformers like current and potential transformer are used in protection and meter indication systems.  These are also used for impedance matching.
  • 17. CONCLUSION:- The method could possibly used for the transfer of electricity across the country via the power lines. The circuit was not supplying the most efficient or increases the voltage out, then the current out must decreases.