SlideShare a Scribd company logo
1 of 21
Download to read offline
Service Repair Manual
Models
140H Motor Grader
Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 8JM
Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 16 20:45:51 UTC+0800 2020
4/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 8JM
Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00456860
1. Remove cover (1) and the gasket.
Illustration 2 g00456923
2. Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
2/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
3. Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order
to remove snap ring (4) .
Illustration 5 g00456926
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 6 g00456927
6. Remove camshaft (6) .
Illustration 7 g00456928
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 8JM
Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
1/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00457491
1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel
injection pump housing.
Illustration 2 g00457492
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the
surface of the fuel injection pump housing.
2/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 3 g00457493
4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install
small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack
bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in
the driver is aligned with the pin in the plate and use a hammer to push the bearing into
position. The bearing will be installed to the correct depth when the shoulder of the driver is
against the plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface
of the housing.
Illustration 4 g00457494
6. Install camshaft (6) .
3/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 5 g00458729
7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push
the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm
(1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of
0.18 ± 0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the
camshaft.
Illustration 6 g00457495
9. Use Tool (A) in order to install snap ring (9) .
4/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 7 g00458730
Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical,
and the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter
is aligned with the pin in the fuel injection pump housing.
Illustration 8 g00458731
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 9 g00458732
12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 16 20:47:43 UTC+0800 2020
6/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 140H MOTOR GRADER 8JM
Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00460164
1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the
engine rotation for approximately 30 degrees. This removes all play from the timing
gears.
Note: If you go past the bolt hole, repeat Step 3.a.
Illustration 2 g00460248
b. Remove plugs (1) and (2) .
2/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
Illustration 3 g00460252
c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be
installed in the flywheel through the hole in the flywheel housing. The No. 1 and No.
6 pistons are now at the TC position. Plug (2) was removed for viewing through
inspection hole (3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves
must have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel
for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC
position.
Illustration 4 g00460258
Typical example
3/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn
fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft,
the fuel injection pump is in the TC position for the No. 1 piston.
Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump
housing and the governor. Put clean engine oil on the seals.
Illustration 5 g00460259
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the
washers. Ensure that Tool (C) remains in place.
Illustration 6 g00460341
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that
Tool (C) is in the notch in the camshaft of the fuel injection pump.
4/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 7 g00460342
9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in
the fuel system. Apply this force in a clockwise direction when the engine is viewed from
the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on
Tool (B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Illustration 8 g00460343
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and
the washers.
5/6
140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP...
2020/2/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

More Related Content

Similar to Caterpillar 140H Motor Grader Fuel System Manual

Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...fjjsekkdmme
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...f8seodkdmdmed3
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...ze6074xunong
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...f8usejkdmmd8i
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...fujkse9didkke3
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...fjkdksmmdm
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...orrf0370383
 
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...dkdmidkkdk
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...fuusejkddmmd3e
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...dujkdksmdmdm
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...jdksmmdmdd
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...hean57759707
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...shenjiao97221
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...s20y0196u
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...shanlianjiu7712
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...jiduanbu
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...iphg8793466
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...tuzhiyou2
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...nye047275
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...lituo39419496
 

Similar to Caterpillar 140H Motor Grader Fuel System Manual (20)

Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual Instant ...
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
Caterpillar Cat 120G Motor Grader (Prefix 4HD) Service Repair Manual (4HD0000...
 

More from rong74gou

Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...
Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...
Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...rong74gou
 
Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...
Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...
Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...rong74gou
 
Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...
Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...
Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...rong74gou
 
Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...
Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...
Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...rong74gou
 
Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...
Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...
Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...rong74gou
 
Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...
Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...
Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...rong74gou
 
Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...
Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...
Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...rong74gou
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...rong74gou
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...rong74gou
 
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...rong74gou
 
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...rong74gou
 
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...rong74gou
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...rong74gou
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...rong74gou
 
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...rong74gou
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...rong74gou
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...rong74gou
 
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...rong74gou
 
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...rong74gou
 
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...rong74gou
 

More from rong74gou (20)

Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...
Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...
Caterpillar Cat M318D Wheeled Excavator (Prefix P8L) Service Repair Manual (P...
 
Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...
Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...
Caterpillar Cat 966H Wheel Loader (Prefix A6D) Service Repair Manual (A6D0000...
 
Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...
Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...
Caterpillar Cat 938G WHEEL LOADER (Prefix 9HS) Service Repair Manual (9HS0000...
 
Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...
Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...
Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2...
 
Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...
Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...
Caterpillar Cat 730 Articulated Truck (Prefix 3T3) Service Repair Manual (3T3...
 
Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...
Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...
Caterpillar Cat 442D Backhoe Loader (Prefix BRG) Service Repair Manual (BRG00...
 
Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...
Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...
Caterpillar Cat 436B BACKHOE LOADER (Prefix 6MJ) Service Repair Manual (6MJ00...
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
 
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
 
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
 
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
 
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
 
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
 
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
 
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
 

Recently uploaded

原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档208367051
 
Pros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptxPros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptxjennifermiller8137
 
办理克莱姆森大学毕业证成绩单|购买美国文凭证书
办理克莱姆森大学毕业证成绩单|购买美国文凭证书办理克莱姆森大学毕业证成绩单|购买美国文凭证书
办理克莱姆森大学毕业证成绩单|购买美国文凭证书zdzoqco
 
原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档208367051
 
Control-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAGControl-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAGVikrantPawar37
 
Welcome to Auto Know University Orientation
Welcome to Auto Know University OrientationWelcome to Auto Know University Orientation
Welcome to Auto Know University Orientationxlr8sales
 
原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档208367051
 
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!Mint Automotive
 
原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量
原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量
原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量208367051
 
Trent engineer.pptx presentation reports
Trent engineer.pptx presentation reportsTrent engineer.pptx presentation reports
Trent engineer.pptx presentation reportsbasant11731
 
Building a Future Where Everyone Can Ride and Drive Electric by Bridget Gilmore
Building a Future Where Everyone Can Ride and Drive Electric by Bridget GilmoreBuilding a Future Where Everyone Can Ride and Drive Electric by Bridget Gilmore
Building a Future Where Everyone Can Ride and Drive Electric by Bridget GilmoreForth
 
办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书
办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书
办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书zdzoqco
 
248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf
248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf
248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdfkushkruthik555
 
Corolla2000-06Diagramas Toyota Corolla.pdf
Corolla2000-06Diagramas Toyota Corolla.pdfCorolla2000-06Diagramas Toyota Corolla.pdf
Corolla2000-06Diagramas Toyota Corolla.pdfkevintruissi05
 
Lighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light ServiceLighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light ServiceImport Car Center
 
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILESABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILESsriharshaganjam1
 
Mastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX ResidentsMastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX ResidentsRowlett Motorwerks
 
办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书
办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书
办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书zdzoqco
 
-The-Present-Simple-Tense.pdf english hh
-The-Present-Simple-Tense.pdf english hh-The-Present-Simple-Tense.pdf english hh
-The-Present-Simple-Tense.pdf english hhmhamadhawlery16
 

Recently uploaded (19)

原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制中央昆士兰大学毕业证(CQU毕业证)#文凭成绩单#真实留信学历认证永久存档
 
Pros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptxPros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptx
 
办理克莱姆森大学毕业证成绩单|购买美国文凭证书
办理克莱姆森大学毕业证成绩单|购买美国文凭证书办理克莱姆森大学毕业证成绩单|购买美国文凭证书
办理克莱姆森大学毕业证成绩单|购买美国文凭证书
 
原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制宾州州立大学毕业证(PSU毕业证)#文凭成绩单#真实留信学历认证永久存档
 
Control-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAGControl-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAG
 
Welcome to Auto Know University Orientation
Welcome to Auto Know University OrientationWelcome to Auto Know University Orientation
Welcome to Auto Know University Orientation
 
原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档
原版1:1定制阳光海岸大学毕业证(JCU毕业证)#文凭成绩单#真实留信学历认证永久存档
 
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
 
原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量
原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量
原版1:1定制(IC大学毕业证)帝国理工学院大学毕业证国外文凭复刻成绩单#电子版制作#留信入库#多年经营绝对保证质量
 
Trent engineer.pptx presentation reports
Trent engineer.pptx presentation reportsTrent engineer.pptx presentation reports
Trent engineer.pptx presentation reports
 
Building a Future Where Everyone Can Ride and Drive Electric by Bridget Gilmore
Building a Future Where Everyone Can Ride and Drive Electric by Bridget GilmoreBuilding a Future Where Everyone Can Ride and Drive Electric by Bridget Gilmore
Building a Future Where Everyone Can Ride and Drive Electric by Bridget Gilmore
 
办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书
办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书
办理萨省大学毕业证成绩单|购买加拿大USASK文凭证书
 
248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf
248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf
248649330-Animatronics-Technical-Seminar-Report-by-Aswin-Sarang.pdf
 
Corolla2000-06Diagramas Toyota Corolla.pdf
Corolla2000-06Diagramas Toyota Corolla.pdfCorolla2000-06Diagramas Toyota Corolla.pdf
Corolla2000-06Diagramas Toyota Corolla.pdf
 
Lighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light ServiceLighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light Service
 
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILESABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
 
Mastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX ResidentsMastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
 
办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书
办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书
办理乔治布朗学院毕业证成绩单|购买加拿大文凭证书
 
-The-Present-Simple-Tense.pdf english hh
-The-Present-Simple-Tense.pdf english hh-The-Present-Simple-Tense.pdf english hh
-The-Present-Simple-Tense.pdf english hh
 

Caterpillar 140H Motor Grader Fuel System Manual

  • 2. Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140H MOTOR GRADER 8JM Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine Disassembly and Assembly 3304B and 3306B Engines for Caterpillar Built Machines Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013 i07103919 Fuel Injection Pump Housing and Governor - Remove SMCS - 1286-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 8S-2264 Pump Impeller Puller 1 8B-7560 Step Plate 1 0T-0513 Bolt 2 5P-1075 Hard Washer 2 Start By: a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 3. Illustration 1 g00589938 3304B Engine 1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27). Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal is damaged. Remove the gaskets and the screen from the top of the turbocharger. Note: The following illustrations are of a 3306B engine. Illustration 2 g00452289 2. Remove six nuts (1) and the washers and remove cover (2). Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of the housing together. Apply thread sealant to the mounting studs and reinstall the mounting studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch). 2/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 4. Illustration 3 g00452292 3. Remove center bolt (3) and spacer (4). Illustration 4 g00452293 4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown. Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection pump camshaft. 5. Remove Tool (A) and bolt (3). Illustration 5 g00452301 3/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 5. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9). Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6) with the filter and the gasket. Illustration 6 g00452302 7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket. Remove tube assembly (13). Illustration 7 g00452343 8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor. Note: Remove the heat shield (not shown) if equipped. 9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the washers. Remove the fuel injection pump housing and the governor from the engine. To safely remove the fuel injection pump housing and the governor, use two technicians or a suitable lifting device. The weight of the 3304B fuel injection pump housing and governor is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is 32 Kg (70 lb). 10. Remove the O-ring seals from the fuel injection pump housing and the governor. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Feb 16 20:45:51 UTC+0800 2020 4/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 6. Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140H MOTOR GRADER 8JM Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine Disassembly and Assembly 3304B and 3306B Engines for Caterpillar Built Machines Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013 i01139602 Fuel Injection Pump Housing - Disassemble SMCS - 1253-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-1860 Retaining Ring Pliers 1 Start By: A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble". B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 7. Illustration 1 g00456860 1. Remove cover (1) and the gasket. Illustration 2 g00456923 2. Remove fuel rack (2) from the fuel injection pump housing. Illustration 3 g00456924 2/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 8. Note: If the original lifters are being reused in the fuel injection pump housing, place identification marks on the lifters in order to identify the locations. 3. Remove lifters (3) from the fuel injection pump housing. Illustration 4 g00456925 4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order to remove snap ring (4) . Illustration 5 g00456926 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing in order to loosen washer (5). Remove washer (5) . 3/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 9. Illustration 6 g00456927 6. Remove camshaft (6) . Illustration 7 g00456928 7. Remove bearings (7) from the drive end of the fuel injection pump housing. Illustration 8 g00456930 8. Remove bearings (8) from the governor end of the fuel injection pump housing. 4/5 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 10. Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140H MOTOR GRADER 8JM Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine Disassembly and Assembly 3304B and 3306B Engines for Caterpillar Built Machines Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013 i01138035 Fuel Injection Pump Housing - Assemble SMCS - 1253-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-1860 Retaining Ring Pliers 1 B 1P-0510 Driver Group 1 C 6V-2016 Plate 1 0S-1594 Bolt 2 6V-4818 Driver 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are clear. 1/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 11. Illustration 1 g00457491 1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the surface of the fuel injection pump housing. 2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel injection pump housing. Illustration 2 g00457492 3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump housing. The bearing joint should be facing toward the top of the fuel injection pump housing. Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the surface of the fuel injection pump housing. 2/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 12. Illustration 3 g00457493 4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in the driver is aligned with the pin in the plate and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against the plate. 5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface of the housing. Illustration 4 g00457494 6. Install camshaft (6) . 3/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 13. Illustration 5 g00458729 7. Put the fuel injection pump housing upright, as shown. Place a wood block under the camshaft. 8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm (1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of 0.18 ± 0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the camshaft. Illustration 6 g00457495 9. Use Tool (A) in order to install snap ring (9) . 4/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 14. Illustration 7 g00458730 Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original lifters are being reused, place the lifters in the original locations. New lifters are identical, and the new lifters can be placed in any order. 10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter is aligned with the pin in the fuel injection pump housing. Illustration 8 g00458731 11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of the fuel rack bearing that is at the drive end of the fuel injection pump housing. 5/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 15. Illustration 9 g00458732 12. Install the gasket and cover (12) . End By: a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble". b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Feb 16 20:47:43 UTC+0800 2020 6/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 16. Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 140H MOTOR GRADER 8JM Configuration: 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine Disassembly and Assembly 3304B and 3306B Engines for Caterpillar Built Machines Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013 i01111133 Fuel Injection Pump Housing and Governor - Install SMCS - 1286-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-7307 Engine Turning Tool 1 B 4C-9874 Spanner Wrench 1 C 6V-4186 Fuel Pump Timing Pin 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the timing procedures. Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is given. 1/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 17. Illustration 1 g00460164 1. Remove the electric starting motor. 2. Install Tool (A) into the flywheel housing, as shown. 3. To find the TC position for the No. 1 piston, perform the following procedure: a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the engine rotation for approximately 30 degrees. This removes all play from the timing gears. Note: If you go past the bolt hole, repeat Step 3.a. Illustration 2 g00460248 b. Remove plugs (1) and (2) . 2/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 18. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 19. Illustration 3 g00460252 c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be installed in the flywheel through the hole in the flywheel housing. The No. 1 and No. 6 pistons are now at the TC position. Plug (2) was removed for viewing through inspection hole (3) . Note: The No. 1 piston is on the compression stroke when the valves of the No. 1 cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves must have slight side-to-side movement. d. In order to check the position of the inlet and exhaust valves, remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". 4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC position. Illustration 4 g00460258 Typical example 3/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 20. 5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft, the fuel injection pump is in the TC position for the No. 1 piston. Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary. 6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump housing and the governor. Put clean engine oil on the seals. Illustration 5 g00460259 7. Attach a hoist and put the fuel injection pump housing and the governor in position on the timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the washers. Ensure that Tool (C) remains in place. Illustration 6 g00460341 8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that Tool (C) is in the notch in the camshaft of the fuel injection pump. 4/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 21. Illustration 7 g00460342 9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in the fuel system. Apply this force in a clockwise direction when the engine is viewed from the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on Tool (B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft). Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel. 10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is correct. 11. Install plugs (1) and (2) . 12. Remove Tool (A). Install the electric starting motor. 13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". Illustration 8 g00460343 14. Put cover (14) and the gasket in position. Install four bolts (15) . 15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and the washers. 5/6 140H Motor Grader 8JM00001-UP (MACHINE) POWERED BY 3306 Engine(SEBP... 2020/2/16 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...