Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Datasheet Fluke 345. Hubungi PT. Siwali Swantika 021-45850618

200 views

Published on

Datasheet Power Quality Clamp Meter. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264

Published in: Engineering
  • Be the first to comment

  • Be the first to like this

Datasheet Fluke 345. Hubungi PT. Siwali Swantika 021-45850618

  1. 1. Technical DataTechnical Data • AC/DC current: Clamp-on measurement of ac current up to 1400 A rms and dc current up to 2000 A without breaking the circuit • Highest safety rating: 600 V CAT IV rated for use at the service entrance • Accurate in noisy environments: Even with distorted waveforms present on electronic loads with low-pass filter • Data logging: Identify intermittent faults by logging any power parameters for minutes or months, including harmonics • Verify batteries: Direct measurement of dc ripple (%) for battery and dc systems • Troubleshoot harmonics: Analyze and log harmonics digitally or graphically • Inrush current: Capture and analyze nuisance tripping, from 3 seconds to 300 seconds • Easy to use: Easily confirm instrument setup with large backlit color display of waveforms and trends • 3-Phase power: Built in capability for balanced loads • View graphs and generate reports: With included Power Log software Fluke 345 Power Quality Clamp Meter With a bright color display to analyze the harmonic spectrum, a low-pass filter to remove high frequency noise, and a high EMC immunity design, the Fluke 345 is ideal for measurements on switching loads such as variable frequency drives, electronic lighting and UPS systems. Additionally, the Hall Effect measurement system makes measurement of dc current possible without the need to break the circuit, and the internal memory enables long-term logging for analysis of trends or intermittent problems. The ideal meter for commissioning and troubleshooting modern electrical loads N10140
  2. 2. 2 Fluke Corporation Fluke 345 Power Quality Clamp Meter Log measured parameters All voltage, current, power, and harmonic measurements can be logged for minutes, hours, or months. Measurement averaging periods from 1 second to 15 minutes can be selected depending on the application. Measured parameters can be logged into three separate recording memory areas. If longer recordings are required, the three areas may be combined into one. Stored measurements can be recalled and displayed on-screen in normal screen format or downloaded using the Power Log software package. Applications Set up and troubleshoot variable frequency drives and UPS systems - Verify correct operation by measuring key parameters Harmonics measurements - Uncover harmonic issues that can damage or disrupt critical equipment Inrush capture - Check start-up current where spurious resets or nuisance circuit breaker tripping occurs Load studies - Verify electrical system capacity before adding loads Image Placeholder (application photo related to VFDs) Harmonics measurements—view key harmonic factors such as distortion factor and total harmonic distortion, as well as individual harmonics up to the 30th harmonic. Log parameters over time to track down intermittent faults.
  3. 3. 3 Fluke Corporation Fluke 345 Power Quality Clamp Meter Flexible and easy to use The 345 measures a wide range of electrical parameters and can be used for many applications in today’s modern electrical environment. Measuring mode is selected by a simple turn of the rotary switch and the large color display presents data in a clear, easy-to-understand way. By default the display will show the most common measurements, in very large format. If more detailed views are required they are available with the press of a single key (up to six measurements at once). Equipment performance measurement - power consumed by single- and three-phase balanced loads. View waveforms for equipment checking and setup. View recorded data in simple graphs and tables. Easily customize the report. Create professional reports. Analysis and reporting software Designed to quickly view recorded data, the included Power Log software displays all recorded parameters on interactive trends. Generate professional reports with the ‘Report Writer’ function, or copy and paste images into report document manually. • Easy-to-use tabbed window format allows quick data evaluation. • One-step download and display capability • Waveform, harmonics, and trend download • Simple data export to other applications Inrush current Diagnose equipment start-ups with the inrush current mode. A current trigger level is set prior to recording. Once the level has been exceeded, the meter will begin capture. Recordings from 3 seconds to 300 seconds may be captured, and up to 1000 inrush events may be stored in the instruments memory. Screen captures and data logging Any measurement can be stored in memory for later viewing, or downloaded to a PC. Simply press ‘SAVE’ to capture the active screen to memory – up to 50 screen shots can be saved for quick and simple documentation. Additionally, over 150,000 individual measurements can be logged for later review on the display or on a PC using Power Log software.
  4. 4. 4 Fluke Corporation Fluke 345 Power Quality Clamp Meter Display Color transmissive LCD 320 x 240 pixels (70 mm diagonal) with 2 level backlight Power supply Battery type 1.5 V Alkaline AA MN 1500 or IEC LR6 x 6 Battery life typically > 10 hours (backlight on full) > 12 hours (backlight reduced) Battery Eliminator BE345 Input 110 V/230 V, 50/60 Hz Output 15 V dc, 300 mA Ambient conditions (For indoor use only) Reference conditions All accuracies stated at 23 °C ± 1 °C (73.4 °F ± 1.8 °F) Operating temperature 0 °C to 50 °C (32 °F to 122 °F) Temperature coefficient of current ≤ ± 0.15 % of rdg per °C Temperature coefficient of voltage ≤ ± 0.15 % of rdg per °C Maximum relative humidity 80 % for temperatures up to 31 °C (87 °F) decreasing linearly to 50 % relative humidity at 40 °C (104 °F) Maximum operating altitude 2000 m Electrical safety Safety IEC 61010-1 600 V CAT IV, double or reinforced insulation, pollution degree 2 Protection IP40; EN60529 Maximum safe working voltages Current measurement 600 V ac rms or dc between uninsulated conductor and ground Voltage measurement 600 V ac rms or dc between either input terminal and ground, or 825 V between energized phase voltages (delta power config.) EMC Emission IEC/EN 61326-1:1997 class B Immunity IEC/EN 61326-1:1997 Mechanical Dimensions (length x width x depth) 300 mm x 98 mm x 52 mm (12 in x 3.75 in x 2 in) Weight including batteries 820 g/1.8 lb Jaw opening 60 mm Jaw capacity 58 mm diameter Cleaning The unit can be cleaned with an Isopropanol impregnated cloth. Do not use abrasives or other solvents. General Specifications
  5. 5. 5 Fluke Corporation Fluke 345 Power Quality Clamp Meter Electrical data All accuracies stated at 23 °C ± 1 °C (73.4 °F ± 1.8 °F). See Ambient conditions specifications for temperature coefficients. Current measurement (dc, dc rms, ac rms) Measuring range 0 to 2000 A dc or 1400 ac rms Autorange facility 40 A/400 A/2000 A Resolution 10 mA in 40 A range 100 mA in 400 A range 1 A in 2000 A range Accuracy DC and dc rms I > 10 A ± 1.5 % rdg ± 5 digits I < 10 A ± 0.2 A AVG I > 10 A ± 3 % rdg ± 5 digits I < 10 A ± 0.5 A Pk I > 10 A ± 5 % rdg ± 5 digits I < 10 A ± 0.5 A AHr I > 10 A ± 2 % rdg ± 5 digits I < 10 A ± 0.5 AHr CF (Crest Factor) 1.1 ≤ CF < 3 ± 3 % rdg ± 5 digits 3 ≤ CF < 5 ± 5 % rdg ± 5 digits Resolution 0.01 RPL (Ripple) 2 % ≤ RPL < 100 % ± 3 % rdg ± 5 digits 100 % ≤ RPL < 600 % ± 5 % rdg ± 5 digits Resolution 0.1 % Idc > 5 A, Iac > 2 A All measurements dc and 15 Hz to 1 kHz Maximum overload 10,000 A or rms x frequency < 400,000 Amps rms is a true-rms measurement (ac + dc) Specifications
  6. 6. 6 Fluke Corporation Fluke 345 Power Quality Clamp Meter Voltage measurement (dc, dc rms, ac rms) Measuring range 0 to 825 V dc or ac rms Autorange facility 4 V/40 V/400 V/750 V Resolution 1 mV in 4 V range 10 mV in 40 V range 100 mV in 400 V range 1 V in 750 V range Accuracy DC and dc rms V > 1 V ± 1 % rdg ± 5 digits V < 1 V ± 0.02 V AVG V > 1 V ± 3 % rdg ± 5 digits V < 1 V 0.03 V Pk V > 1 V ± 5 % rdg ± 5 digits V < 1 V ± 0.03 V CF (Crest Factor) 1.1 ≤ CF < 3 ± 3 % rdg ± 5 digits 3 ≤ CF < 5 ± 5 % rdg ± 5 digits Resolution 0.01 RPL (Ripple) 2 % ≤ RPL < 100 % ± 3 % rdg ± 5 digits 100 % ≤ RPL < 600 % ± 5 % rdg ± 5 digits Resolution 0.1 % Vdc > 0.5 V, Vac > 0.2 V All measurements dc and 15 Hz to 1 kHz Maximum overload 1,000 V rms Volts rms is a true-rms measurement (ac + dc) Harmonics THD (Total Harmonic Distortion) 1 % ≤ THD < 100 % ± 3 % rdg ± 5 digits 100 % ≤ THD < 600 % ± 5 % rdg ± 5 digits Resolution 0.1 % DF (Distortion Factor) 1 % ≤ DF < 100 % ± 3 % rdg ± 5 digits Resolution 0.1 % H02 ≤ Vharm < H13 ± 5 % rdg ± 2 digits H13 ≤ Vharm ≤ H30 ± 10 % rdg ± 2 digits All measurements up to 30th harmonic (40th harmonic for 15 Hz to 22 Hz) Frequency range F0 15 Hz to 22 Hz and 45 Hz to 65 Hz Vacrms > 1V
  7. 7. 7 Fluke Corporation Fluke 345 Power Quality Clamp Meter Watts measurement (single- and three-phase) (dc, dc rms, ac rms) Measuring range 0 to 1650 kW dc or 1200 kW ac Autoranging facility 4 kW, 40 kW, 400 kW, 1650 kW ac Resolution 1 W in 4 kW 10 W in 40 kW 100 W in 400 kW 1 kW in 1200 kW Accuracy 2.5 % rdg ± 5 digits W1Ø < 2 kW ± 0.08 kW W3Ø < 4 kW ± 0.25 kW VA measurement (single- and three-phase) (dc, dc rms, ac rms) Measuring range 0 to 1650 kVA dc or 1200 kVA ac Autorange facility 4 kVA, 40 kVA, 400 kVA, 1650 kVA Resolution 1 VA in 4 kVA 10 VA in 40 kVA 100 VA in 400 kVA 1 kVA in 1200 kVA Accuracy VA > 2 kVA 2.5 % rdg ± 5 digits VA < 2 kVA ± 0.08 kVA VAR measurement (single- and three-phase) Measuring range 0 to 1250 kVAR Autorange facility 4 kVAR, 40 kVAR, 400 kVAR, 1200 kVAR Resolution 1 VAR in 4 kVAR 10 VAR in 40 kVAR 100 VAR in 400 kVAR 1 kVAR in 1200 kVAR Accuracy VAR > 4 kVAR ± 2.5 % rdg ± 5 digits VAR < 4 kVAR ± 0.25 kVAR Power factor range 0.3 < PF < 0.99 Power factor (single- and three-phase) Power factor Measuring range 0.3 capacitive and 1.0 to 0.3 inductive (72.5° capacitive and 0° to 72.5° inductive) Resolution 0.001 Accuracy ± 3° Frequency range 15 Hz to 1 kHz Displacement power factor Measuring range 0.3 capacitive and 1.0 to 0.3 inductive (72.5° capacitive and 0° to 72.5° inductive) Resolution 0.001 Accuracy ± 3° Frequency range 15 Hz to 22 Hz and 45 Hz to 65 Hz
  8. 8. 8 Fluke Corporation Fluke 345 Power Quality Clamp Meter Kilowatt hour (kWHr) Measuring range 40,000 kWHr Autorange facility 1 kWHr, 40 kWHr, 400 kWHr, 4,000 kWHr, 40,000 kWHr Resolution 1 WHr in 4 kWHr 10 WHr in 40 kWHr 100 WHr in 400 kWHr 1 kWHr in 4,000 kWHr 10 kWHr in 40,000 kWHr Accuracy kWHr > 2 kWHr ± 3 % ± 5 digits kWHr < 2 kWHr ± 0.08 kWHr All Watts /VA /VAR /PF measurements Frequency range DC and 15 Hz to 1 kHz Current range 10 A to 1400 A rms Voltage range 1 V to 825 V rms Maximum input 825 V rms/1400 A rms Maximum overload 1000 V rms/10,000 A Frequency measurement (from current or voltage sources) Measuring range 15 Hz to 1 kHz Resolution 0.1 Hz Accuracy 15 to 22 Hz ± 0.5 % rdg 40 Hz to 70 Hz ± 0.5 % rdg 15 Hz to 1000 Hz ± 1% rdg Current range 10 A to 1400 A rms Voltage range 1 V to 825 V rms Scope function Current measurement Ranges 10 A/20 A/40 A/100 A/200 A/400 A/1000 A/2000 A Resolution 1 A in 40 A 10 A in 400 A 50 A in 2000 A Accuracy ± 3 % rdg ± 1 pixel Maximum overload 10,000 A Voltage measurement Ranges 4 V/10 V/20 V/40 V/100 V/200 V/400 V/1000 V Resolution 100 mV in 4 V 1 V in 40 V 10 V in 400 V 31.25 V in 1000 V Accuracy ± 2 % rdg ± 1 pixel Maximum overload 1000 V rms Frequency range DC and 15 Hz to 600 Hz Time base 2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms/div Refresh rate 0.5 seconds Maximum sampling rate 15.625 kHz
  9. 9. 9 Fluke Corporation Fluke 345 Power Quality Clamp Meter Inrush current function Ranges 40 A, 400 A, and 2000 A Resolution 10 mA in 40 A range 100 mA in 400 A range 1 A in 2000 A range Accuracy I > 10 A ± 5 % rdg ± 1 pixel I < 10 A ± 0.5 A All measurements dc and 15 Hz to 1 kHz Maximum overload Maximum overload 10,000 A or rms x frequency < 400,000 Amps rms is a true-rms measurement (ac + dc) Capture time 1 s, 3 s, 10 s, 30 s, 100 s, and 300 s Maximum sampling rate 15.625 kHz Interface USB Interface to a PC Power Log software for download, analysis, and reporting 345 Upgrade Utility for installing a new firmware version Logging Memory Logging areas Three areas that can be used individually or combined into one large area Averaging periods 1 s, 2 s, 5 s, 10 s, 30 s, 1 min, 5 min, 10 min, 15 min, and custom
  10. 10. 10 Fluke Corporation Fluke 345 Power Quality Clamp Meter Logging times Volts and current mode Average time Logging time (1 area) Logging time (3 areas) 1 s 1 h 49 m 5 h 12 m 2 s 3 h 38 m 10 h 24 m 5 s 9 h 06 m 1 d 2 h 00 m 10 s 18 h 12 m 2 d 04 h 00 m 30 s 2 d 06 h 36 m 6 d 12 h 01 m 1 min 4 d 13 h 12 m 13 d 00 h 03 m 5 min 22 d 18 h 00 m 65 d 00 h 15 m 10 min 45 d 12 h 00 m 130 d 00 h 30 m 15 min 68 d 06 h 00 m 195 d 00 h 45 m V & A harmonics mode Average time Logging time (1 area) Logging time (3 areas) 1 s 0 h 34 m 1 h 38 m 2 s 1 h 08 m 3 h 16 m 5 s 2 h 52 m 08 h 11 m 10 s 5 h 44 m 16 h 23 m 30 s 17 h 13 m 2 d 01 h 11 m 1 min 1 d 10 h 26 m 4 d 02 h 23 m 5 min 7 d 04 h 10 m 20 d 11 h 25 m 10 min 14 d 08 h 20 m 81 d 0 h 50 m 15 min 21 d 12 h 30 m 121 d 13 h 15 m single- and three-phase power mode Average Time Logging Time (1 area) Logging Time (3 areas) 1 s 1 h 40 m 4 h 47 m 2 s 3 h 21 m 9 h 34 m 5 s 8 h 22 m 23 h 57 m 10 s 16 h 45 m 1 d 23 h 54 m 30 s 2 d 02 h 17 m 5 d 23 h 42 m 1 min 4 d 04 h 35 m 11 d 23 h 25 m 5 min 20 d 22 h 55 m 59 d 21 h 05 m 10 min 41 d 21 h 50 m 119 d 18 h 10 m 15 min 62 d 20 h 45 m 179 d 15 h 15 m
  11. 11. 11 Fluke Corporation Fluke 345 Power Quality Clamp Meter Fluke Corporation PO Box 9090, Everett, WA USA 98206 Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands For more information call: In the U.S.A. (800) 443-5853 or Fax (425) 446-5116 In Europe/M-East/Africa +31 (0) 40 2675 200 or Fax +31 (0) 40 2675 222 In Canada (800) 36-FLUKE or Fax (905) 890-6866 From other countries +1 (425) 446-5500 or Fax +1 (425) 446-5116 Web access: http://www.fluke.com ©2007 Fluke Corporation. All rights reserved. Specifications subject to change without notice. Printed in U.S.A. 1/2007 2643038 D-EN-N Rev C Fluke.Keeping your world up and running.™ Ordering information Fluke-345 Power Quality Clamp Meter Includes Soft carrying case Power Log software Test leads Alligator clips Test probes USB cable International ac adapter / battery eliminator Printed English language user manual Multi-language manual CD Recommended Accessories: TP220 SureGrip™ Industrial Test Probes - One pair (red, black) of Industrial test probes. Sharp, 12 mm stainless steel tip provides reliable contact. Use with TL224 test leads. AC220 SureGrip™ Alligator Clips - One pair (red, black) of small, insulated, nickel plated jaws. Blunt tip grabs round screw heads up to 9.5 mm. Use with TL224 test leads. TP1 Slim Reach Test Probes - One pair (red, black) of slender probe bodies for probing closely spaced or recessed terminals. Hard stainless steel probe tips with flat blade design to hold securely in blade type electrical wall sockets. L200 Probe Light - Small, rugged, and light the L200 easily attaches to any Fluke test probe. Bright white LED illuminates contact area and frees hands for work. L210 Probe Light and Probe Extenders - Includes L200 Probe Light and TP280 Test Probe Extenders to keep hands away from live circuits and light work area C550 Tool Bag - Steel reinforced frame with heavy duty hardware and large zippered storage compartment includes 25 pockets. Allows you to carry all your tools to the job site. TLK291 - Fused Test Leads provide extra safety with retractable sheath protecting contact points.

×