Upcoming SlideShare
×

# Induction Synchronous Motor

38,853 views

Published on

• Full Name
Comment goes here.

Are you sure you want to Yes No

Are you sure you want to  Yes  No
• perfect ppts

Are you sure you want to  Yes  No
• nice n tanq

Are you sure you want to  Yes  No
• good

Are you sure you want to  Yes  No
• great work

Are you sure you want to  Yes  No

### Induction Synchronous Motor

1. 1. Motor ELECTRICAL ENERGY Mechanical Energy
2. 2. Index <ul><li>Classification </li></ul><ul><li>Laws of electromagnetism </li></ul><ul><li>Rotating Magnetic Field </li></ul><ul><li>AC Motor </li></ul><ul><li>Induction Motor </li></ul><ul><li>Synchronous Motor </li></ul><ul><li>Maintenance Practices </li></ul>
3. 3. Laws of Electromagnetism <ul><li>Faraday’s Law </li></ul><ul><li>Lenz’s Law </li></ul><ul><li>Fleming’s Right Hand rule </li></ul><ul><li>Fleming’s Left Hand rule </li></ul><ul><li>Interaction of two magnetic fields </li></ul>
4. 4. Faraday’s Law of Electromagnetic Induction <ul><li>When the magnetic flux through a circuit is changing an induced EMF is setup in that circuit and its magnitude is proportional to the rate of change of flux” </li></ul><ul><li>Simulation </li></ul>
5. 5. Lenz’s Law <ul><li>“ The direction of an induced EMF is such that its effect tends to oppose the change producing it” </li></ul><ul><li>Simulation </li></ul>
6. 6. Fleming’s Right Hand rule <ul><li>Used to measure the direction of induced current in a conductor when cut by a magnetic field. </li></ul>
7. 7. Fleming’s Left Hand rule <ul><li>Used to measure the direction of motion of a current carrying conductor when placed in magnetic field. </li></ul>
8. 8. Interaction of two magnetic fields
9. 9. Production of Three Phase Rotating Magnetic Field <ul><li>RMF may be set up in two-phase or three-phase machines. </li></ul><ul><li>The number of pole pairs must be the same as the number of phases in the applied voltage. </li></ul><ul><li>The poles are displaced from each other by an angle equal to the phase angle between the individual phases of the applied voltage. </li></ul>
10. 10. + When Current positive and going into · When Current negative and coming from
11. 11. Speed of RMF <ul><li>The magnetic field established rotates at a speed given by </li></ul><ul><li>N = 60* f / P </li></ul><ul><li>where f = frequency of stator current </li></ul><ul><li>P = Number of pair of poles </li></ul>
12. 12. A machine which converts AC electrical energy into Mechanical energy
13. 13. Induction Motor <ul><li>Introduction </li></ul><ul><li>Construction </li></ul><ul><li>Principle of Induction Motor </li></ul><ul><li>Slip </li></ul><ul><li>Starting Current </li></ul><ul><li>Torque </li></ul><ul><li>Torque Speed characteristics </li></ul><ul><li>Two Phase Induction Motor </li></ul><ul><li>Single phase Induction Motor </li></ul><ul><li>Summary </li></ul><ul><li>Uses in Aircraft </li></ul>
14. 14. Induction Motor-Intro. <ul><li>The induction motor is the most commonly used type of ac motor. It is simple, low cost and rugged in construction. </li></ul><ul><li>The induction motor derives its name from the fact that ac voltages are induced in the rotor circuit by the rotating magnetic field of the stator. </li></ul>
15. 15. Stator Wound Rotor Start Resistance
16. 16. AC Machine Stator
17. 17. Squirrel Cage Rotor
18. 19. Principle of Induction Motor
19. 20. Slip in Induction Motor slip speed = synchronous speed - rotor speed measured in RPM Slip = (synchronous speed - rotor speed ) /synchronous speed expressed as a percentage The greater the slip speed, the greater is the force on each conductor and the torque exerted by the whole. 
20. 21. Starting Current <ul><li>The starting current is very high which may damage the stator winding. </li></ul><ul><li>To reduce this heavy starting current, star-delta starting switch is used. </li></ul><ul><li>For starting, the stator winding are connected up in star via the switch to the supply so that the phase voltage is 1/ √3 of the normal voltage. This reduced voltage limits the starting current. </li></ul>
21. 22. phase voltage is 1/ √3 of the normal voltage phase voltage is equal to the line voltage.
22. 23. Torque- Starting <ul><li>The resistance of the squirrel cage rotor </li></ul><ul><li>is small and inductance high. </li></ul><ul><li>Thus on starting rotor current and the rotor emf are nearly 90 degrees out of phase. </li></ul><ul><li>The lagging rotor current interacts little with stator current and therefore the starting torque is poor. </li></ul>
23. 24. <ul><li>As the rotor current come into phase with the rotor emf with increased rotor speed (decreased slip and inductive reactance) the rotor and the stator flux comes more into phase and the torque increases. </li></ul>Torque- Running
24. 25. Methods Of Improving Starting Torque <ul><li>In creasing the resistance of the rotor conductors </li></ul><ul><li>Using a combination of high and low resistance conductors </li></ul><ul><li>Using a wire wound rotor connected to variable resistor </li></ul>
25. 26. Wire Wound Rotor Connected To Resistor
26. 27. Torque –Speed Characteristic
27. 28. Two Phase Induction Motor
28. 29. Two Phase RMF
29. 30. Single Phase Pulsating Field
30. 31. Single Phase Induction Motor <ul><li>The single phase induction motor produces a pulsating field. </li></ul><ul><li>However, if the rotor is rotated forward at a bit less than the synchronous speed, It will develop some torque. </li></ul><ul><li>If the rotor is started in the reverse direction, it will develop a same torque in other direction </li></ul>
31. 32. Split Phase Induction Motor <ul><li>Two phases are produced by splitting a single phase. </li></ul><ul><li>A capacitor is inserted in one of the windings and is called a permanent-split capacitor motor. </li></ul><ul><li>The direction of the motor is easily reversed by switching the capacitor in series with the other winding. </li></ul>
32. 33. Summary <ul><li>The three phase induction motor </li></ul><ul><li>Is very robust in construction </li></ul><ul><li>No need for slip rings and therefore less maintenance. </li></ul><ul><li>Has a high starting current reduced by star-delta switch. </li></ul><ul><li>Has a poor starting torque. </li></ul><ul><li>Runs at a speed less than synchronous speed. </li></ul>
33. 34. <ul><li>Direction of rotation can be reversed by interchanging any two stator phases. </li></ul><ul><li>Is of two types depending on motor construction: Squirrel Cage or Slip Ring </li></ul>
34. 35. Uses in Aircraft <ul><li>Constant speed with varying loads and require smoother torque e.g. fuel booster pumps, hydraulic system’s Electric Motor Driven pumps. </li></ul><ul><li>Systems which need high torque and reversing e.g. Flap Power units (for alternate flap drives), Stabilizer Trim Actuator. </li></ul><ul><li>Two phase induction motors also used in aircraft such as aileron trim actuators and in reversible valve actuators in Fuel, hydraulic, oil, and pneumatic systems etc. </li></ul>
35. 36. Induction Motor Example A 100 hp, 8 pole, 60 Hz, 3 phase induction motor runs at 891 rpm under full load. Determine the synchronous speed in rpm, slip speed and Slip. Solution on white board
36. 37. Synchronous Motor <ul><li>Synchronous Motor-Intro </li></ul><ul><li>Synchronous Motor-principle </li></ul><ul><li>Changing the Load </li></ul><ul><li>Starting Torque </li></ul><ul><li>Improvement of starting torque </li></ul><ul><li>Synchronous Machine Construction </li></ul><ul><li>V curves </li></ul><ul><li>Torque versus Speed </li></ul><ul><li>Summary </li></ul>
37. 38. Synchronous Motor- Intro <ul><li>The synchronous motor rotates at the synchronous speed i.e. the speed of the RMF. </li></ul><ul><li>Stator is similar in construction to that of an induction motor, so same principle is applied to the synchronous motor rotor. </li></ul><ul><li>Field excitation is provided on the rotor by either permanent or electromagnets with number of poles equal to the poles of the RMF caused by stator </li></ul>
38. 39. Synchronous Motor-Principle The rotor acting as a bar magnet will turn to line up with the rotating magnet field. The rotor gets locked to the RMF and rotates unlike induction motor at synchronous speed under all load condition
39. 40. Changing The Load An increase in the load will cause the rotor to lag the stator field but still maintain synchronous speed. Increase in load has increased the torque component, but the field strength has decreased due to the increase in length of the air gap between the rotor and the stator. If the synchronous motor is overloaded it pulls out of synchronism and comes to rest. The minimum amount of torque which causes this is called the “ pull out torque”. Lightly loaded motor Heavily loaded motor
40. 41. Starting Torque <ul><li>It cannot be started from a standstill by applying ac to the stator. When ac is applied to the stator a high speed RMF appears around the stator. This RMF rushes past the rotor poles so quickly that the rotor is unable to get started. It is attracted first in one direction and then in the other and hence no starting torque. </li></ul>
41. 42. Improvement of starting torque <ul><li>It is started by using a squirrel cage within a rotor construction and therefore starts as an induction motor. </li></ul><ul><li>At synchronous speed the squirrel cage has no part to play. </li></ul>
42. 43. Synchronous Machine Construction
43. 44. Synchronous Machine Phasor Diagram
44. 45. Excitation and Stator induced voltage
45. 46. V curves
46. 47. Torque versus Speed
47. 48. Summary <ul><li>The synchronous motor: </li></ul><ul><li>requires to be started by an external prime mover. </li></ul><ul><li>Runs only at synchronous speed, this is an advantage where continuous speed is required but a disadvantage where a variable speed is required. </li></ul><ul><li>Can be used to adjust the power factor of a system at the same time it is driving a mechanical load. </li></ul>
48. 49. Maintenance Practices-A.C. Motors <ul><li>Clean, but don’t forget to inspect before and after cleaning </li></ul><ul><li>Check electrical connections for security, the insulation to be in satisfactory condition. </li></ul><ul><li>Examine for signs of over heating </li></ul><ul><li>Check that the motor is secure </li></ul><ul><li>Do an audible check </li></ul><ul><li>Ensure that the motor is not over heating when operating, a rule of thumb is that if it is too hot for the hand, it is too high. </li></ul><ul><li>When replacing a motor always ensure that the load, valve has not seized. </li></ul><ul><li>Also ensure that the motor operates in the correct direction </li></ul><ul><li>End of Motors </li></ul>