Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.
SECUBIO TECHNOLOGY(CHINA) HOLDINGS CO.,LTD         ‫اﻟﺒﺼ ﻤﺎت ﻣﺎﺳ ﺤﺔ, اﻟﺤﻀ ﻮر وﻗ ﺖ ﺑﺼ ﻤﺔ, اﻟ ﺪﺧﻮل ﻟﻤﺮاﻗﺒ ﺔ اﻷﺻ ﺎﺑﻊ ﺑﺼ ﻤﺎت‬H...
SECUBIO TECHNOLOGY(CHINA) HOLDINGS CO.,LTD         ‫اﻟﺒﺼ ﻤﺎت ﻣﺎﺳ ﺤﺔ, اﻟﺤﻀ ﻮر وﻗ ﺖ ﺑﺼ ﻤﺔ, اﻟ ﺪﺧﻮل ﻟﻤﺮاﻗﺒ ﺔ اﻷﺻ ﺎﺑﻊ ﺑﺼ ﻤﺎت‬B...
Upcoming SlideShare
Loading in …5
×

How to set up TCP/IP LAN Communication between fingerprint reader and software

66,690 views

Published on

TCP/IP Communication

Published in: Technology, Education
  • Be the first to comment

How to set up TCP/IP LAN Communication between fingerprint reader and software

  1. 1. SECUBIO TECHNOLOGY(CHINA) HOLDINGS CO.,LTD ‫اﻟﺒﺼ ﻤﺎت ﻣﺎﺳ ﺤﺔ, اﻟﺤﻀ ﻮر وﻗ ﺖ ﺑﺼ ﻤﺔ, اﻟ ﺪﺧﻮل ﻟﻤﺮاﻗﺒ ﺔ اﻷﺻ ﺎﺑﻊ ﺑﺼ ﻤﺎت‬How to connect device withPC computer by TCP/IP:1. When Power is on, Please make Fingerprint reader connect with Router by Network cable(During its connection, Please double care that it may arise unsuccessfulconnection for the reason of the port disconnected between Network cableand Fingerprint-reader and meanwhile Failure Ping for Fingerprint readercommunication,2. Before operating the Attendance software, Please set up the special parameters exclusively for Fingerprint reader communication as follows: Menu----.Setting-----.CommSet-----OK-----TCPIP-----IP Address(Note: When you set up the IP address for Fingerprint reader, Please double careabout the bellowed information in advance,For instance, the IP address information of PC that we used now is listed below:The IP address between fingerprint reader and PC must be in the same Networksection, but it prohibited to absolutely same together, otherwise it will ariseconflict for IP address,Please see above photo, that’s the LAN communication screenshot, you can findif your PC’ s IP is 192.168.0.144, and accordingly you can freely make the IPaddress of your Fingerprint reader by following address whatever you like,192.168.0.224,192.168.0.223,192.168.0.222192.168.0.212Fingerprint time attendance, Fingerprint access control, card system; www.secubio.com
  2. 2. SECUBIO TECHNOLOGY(CHINA) HOLDINGS CO.,LTD ‫اﻟﺒﺼ ﻤﺎت ﻣﺎﺳ ﺤﺔ, اﻟﺤﻀ ﻮر وﻗ ﺖ ﺑﺼ ﻤﺔ, اﻟ ﺪﺧﻮل ﻟﻤﺮاﻗﺒ ﺔ اﻷﺻ ﺎﺑﻊ ﺑﺼ ﻤﺎت‬But please make sure the last three parameter just like 224,223,222,212 mustbe no more than 224, it’s very important,225 will be prohibited according to regulation of IP address, Meanwhile the IPaddress of your fingerprint reader can not be same as other PC’s IP address inlocal area network(LAN),In other means, there is strictly prohibited that two same IP address in the sameLAN with same Router, No matter what IP address is for PC or fingerprint reader,Otherwise it will be the conflict IP in network,Additionally the device IP in software must be absolutely same with fingerprintreader hardware ( For example , The IP of your PC is192.168.0.144, The Fingerprint reader hardware is 192.168.0.212,andthen the device IP in software must be 192.168.0.212)The detail setting-up of fingerprint reader hardware, Please check photo asfollows just as an example to show ,you how to set up IP address,sunetmast,gateway,port for LAN communication,2) The port of software and fingerprint reader hardware should be thesame one, if port of fingerprint reader is 5005, and accordingly the portof software is 5005,3) The DefGateway must be in the same network section with PC’s IP address,For example, the IP of PC is 192.168.0.144, and then the DefGateway should beset up as 192.168.0.1 (“0” stands for same network section, For “1”,you can’tchange it in any time),4)You can check the video for get more details about how to makeTCP/IP setting-up between software and hardware,,Fingerprint time attendance, Fingerprint access control, card system; www.secubio.com

×