Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Mcq unit ii

6,967 views

Published on

Published in: Technology
  • Be the first to comment

Mcq unit ii

  1. 1. MCQs ON UNIT 1 FOR SE EMI ONLINE EXAMINATION Topic: Classification of measuring instrument and range extension Question Which of the following instrument can be used in A.C. bridges for less frequencies up to 200 Hz only A Head phone B Tunable amplifier detector C Vibration galvanometer D All of the above Answer C Question Which of the following bridge is used in strain gauge measurement A Kelvin bridge B Specially design bridge C Kelvin double bridge D Carey-foster bridge Answer B Question A Megger is basically a A Moving iron type instrument B Moving coil type instrument C Hot wire instrument D Electrolytic instrument Answer B Question Maxwell inductance capacitance bridge is used for measurement of inductance of A Low Q coils only B Medium Q coils only C High Q coils only D Low and Medium Q coils only Answer B Marks 2 Unit 1
  2. 2. Topic: Topic: Classification of measuring instrument and range extension Question The most commonly used null deflector in a power frequency ac bridge is a: A Vibration galvanometer B D'Arsanval galvanometer C Ballistic galvanometer D Tachometer Answer A Question Loss of charge method is used to measure A Low Resistance B High Resistance C Low Inductance D High Inductance Answer B Question Megger is an instrument used for the measurement of: A High resistance and insulation resistance B Medium resistance C Low resistance D Leakage current Answer A Question Anderson bridge is used to measure of: A Inductance B Capacitance C Time period D Resistance and capacitance Answer A Marks 2 Unit 1
  3. 3. Topic: Topic: Classification of measuring instrument and range extension Question Kelvin double bridge is best suited for the measurement of: A Inductance B Capacitance C Low resistance D High resistance Answer C Question The material used to make standard resistance is: A Manganin B Aluminum C Nichrome D Platinum Answer A Question Inductance is measured by which one of the following A Wien bridge B Schering bridge C Maxwell bridge D Owen bridge Answer C Question If a wheat stone bridge is in balance condition then A A heavy current flows through the galvanometer B No current flows through the galvanometer C The current in each of the four arms R1, R2, R3 and R4 are same D A low current flows through the galvanometer Answer B Marks 2 Unit 1
  4. 4. Topic: Topic: Classification of measuring instrument and range extension Question The value of resistance of an earthing electrode depends upon A Shape and material of electrode B Depth to which electrode is driven into earth C Specific resistance of soil D All of the above Answer D Question From the point of view of safety, the resistance of earthing electrode should be A Low B High C Medium D The value of resistance of earth electrode does not affect the safety Answer A Question ------------- is a instrument which measures the insulation resistance of an electrical circuit relative to earth and one another A Tangent galvanometer B Megger C Current transformer D None of the above Answer B Question The controlling torque in a megger is provided by A Springs B Weights attached to the moving system C It does not need any controlling torque D None of the above Answer C Marks 2 Unit 1
  5. 5. Topic: Topic: Classification of measuring instrument and range extension Question The operating voltage of a megger is about A 6V B 120V C 400V D 500V Answer D Question The electrical power to a megger is provided by A Battery B Permanent magnet DC generator C A.C generator D Any of the above Answer B Question For measuring a very high resistance we should use A Kelvins double bridge B Wheatstone bridge C Megger D None of the above Answer C Marks 2 Unit 1
  6. 6. Topic: Topic: Classification of measuring instrument and range extension Question A bride circuit works at a frequency of 2 kHz. The following can be used as detectors for detection of null conditions in the bridge A Vibration galvanometer and head phones B Head phones and tunable amplifiers C Vibration galvanometer and tunable amplifiers D Vibration galvanometer, head phones and tunable amplifiers Answer B Question A Wheatstone bridge cannot be used for precision measurement because errors are introduced on account of A Resistance of connecting leads B Thermo-electric emfs C Connecting resistances D All of the above Answer D Question Which of the following methods will be suitable for the measurement of the resistance of an ammeter shunt A Wheatstone bridge B Kelvin’s double bridge C Maxwell bridge D Wiens bridge Answer B Question Which of the following instrument can be used in ac bridges for less frequencies up to 200 Hz only A Head phones B Tunable amplifiers C Vibration galvanometer D All of the above
  7. 7. Answer C Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question Ohmmeter is A A meter to record ohm B Used to measure resistance C Combination of ohm and meter D An indicating instrument Answer B Question In a megger when not in operation, the pointer shows a resistance of A 0 Ohm B 100 Ohm C 555 Ohm D Infinity Answer D Question A bridge is used for the measurement of capacitance is A Wheatstone bridge B Wiens bridge C Maxwell bridge D Schearing bridge Answer D Question Low resistance from few ohms down to one micro ohm is measured using which one of the following instruments A Ohmmeter B A series type ohmmeter C A shunt type ohmmeter D A voltmeter and ammeter
  8. 8. Answer D Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question In an Anderson bridge, the unknown inductance is measured in terms of A Known inductance and resistance B Known capacitance and resistance C Known resistance D Known inductance Answer B Question For measurement of mutual inductance we can use A Anderson bridge B Maxwell bridge C Heaviside bridge D Any of the above Answer C Question For measurement of inductance having high value, we should use A Maxwell bridge B Maxwell Wein bridge C Hays bridge D Any of the above Answer C Question To avoid the effect of stray magnetic field in a.c bridges we can use A Magnetic screening B Wagner earthing device C Wave filters
  9. 9. D Any of the above Answer A Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question If an inductance is connected in one arm of bridge and resistance in the remaining three arms A The bridge can always be balanced B The bridge cannot be balanced C The bridge can be balanced if the resistance have some specific values D Any of the above Answer B Question Wagner’s Earth device are used in bridge circuit for A Eliminating the effect of earth capacitance B Eliminating the effect of-inter component capacitance C Eliminating the effect of stray electrostatic fields D Shielding the bridge elements Answer A Question Swamping resistance is a resistance which is added to moving coil of a meter to A Reduce full scale current B Reduce the temperature error C Increase the sensitivity D Increase the field strength Answer B Question Kelvin double bridge is best suited for the measurement of A Inductance B Capacitance C Low resistance D High resistance
  10. 10. Answer C Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question The accuracy of Kelvin double bridge for the measurement of low resistance is high because the bridge A Uses two pairs of resistance arms B Has medium value resistance in the ratio arms C Uses a low resistance link between standard and test resistance D Uses a null indicating galvanometer Answer C Question Which instruments has the lowest resistance A Ammeter B Voltmeter C Frequency meter D Megger Answer A Question The sensitivity of a Wheatstone bridge depends upon A Galvanometer current sensitivity B Galvanometer resistance C Bridge supply voltage D All of the above Answer D Question High resistance are provided with a guard terminal in order to A Protect the resistance against stray electrostatic field B Bypass the leakage current C Protect the resistance against overloads
  11. 11. D Protect the resistance against stray electromagnetic field Answer B Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question A high resistance cannot be measured by simple ammeter- voltmeter because A Voltmeter rating will be too high B Ammeter rating will be too low C Leakage current cannot be neglected D Power loss will be high Answer C Question All meters used for measuring current, voltage and resistance are basically A Multimeters B Voltmeters C Ammeters D Ohmmeters Answer B Question Megger is essentially, a A Megohmmeter B Dynamometer C Series type ohmmeter D Shunt type ohmmeter Answer A Question A megger is used for measurement of A Voltage B Flux
  12. 12. C Power D Insulation resistance Answer D Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question The resistance of a shunt for a precision grade ammeter can be best measured by A De Sauty bridge B Schering bridge C Maxwell bridge D Kelvin double bridge Answer D Question The resistance from 0.1 to 1.0 ohm can be measured easily with precision better than 0.5% by A Differential galvanometer B Kelvin double bridge C Potentiometer D Wheatstone bridge Answer B Question The Wheatstone bridge method of resistance measurement is ideally suitable for the measurement of resistance values in the range of A 0.001 Ω to 1 Ω B 0. 1 Ω to 100 Ω C 100 Ω to 10 kΩ D 100 kΩ to 10 MΩ Answer B Question The insulation resistance of a domestic wiring is to be measured. The instrument preferred is A Kelvin double bridge B Ohm meter
  13. 13. C Potentiometer D Megger Answer D Marks 2 Unit 1 Topic: Topic: Classification of measuring instrument and range extension Question The maximum sensitivity of a Wheatstone bridge is achieved when the bridge A Uses dc supply B Uses ac supply C Has unity arm ratio D Has 1:2 arm ratio Answer C Question Inductance comparison bridge uses A One L and one C B One L C One C D None of the above Answer C Question Quality factor Q depends upon A wL/R B 1/wRC C Power stored/ Power lost D Power dissipated/ Power stored Answer A Question Anderson bridge is used for measurement of A Time period B Phase difference C Inductance
  14. 14. D Capacitance Answer C Marks 2 Unit 1

×