SlideShare a Scribd company logo
1 of 23
Download to read offline
Service Repair Manual
Models
320D2 and 320D2 L Excavator
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR ZCS
Configuration: 320D2 & 320D2 L Excavators ZCS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780462
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure .
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure .
NOTICE
1/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Illustration 1 g02706996
2/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 2 g02695979
1. Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the front gear group. Carefully follow the procedure in order to remove the
gear group.
2. Remove plug (4) from the cylinder block. Remove O-ring seal (3) from plug (4).
3. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
4. Install Tooling (B) through Hole (X) in camshaft gear (1) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position.
5. Install Tooling (C) into Hole (Y) in the cylinder block. Use Tooling (C) in order to lock the
crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the
crankshaft during repairs.
6. Apply sufficient pressure to fuel injection pump gear (2) in a counterclockwise direction in
order to remove the backlash. Lock the fuel injection pump in this position. Refer to
Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure.
3/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 3 g02707118
7. Loosen nuts (6) on all rocker arms (7). Unscrew adjusters (5) on all rocker arms (7) until all
valves are fully closed.
Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between
the valves and pistons.
4/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 4 g02706997
Alignment of timing marks
8. Mark gear (1), gear (2), and gear (8) in order to show alignment. Refer to Illustration 4.
Note: Identification will ensure that the gears can be installed in the original alignment.
9. Remove fuel pump gear (2). Refer to Disassembly and Assembly, "Fuel Pump Gear -
Remove and Install" for the correct procedure.
10. Remove camshaft gear (1). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
11. Remove idler gear (8). Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5P-7305 Engine Turning Tool 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
B 230-6284 Timing Pin (Camshaft) 1
D
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
6/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 5 g02706999
1. If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the
compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top
Center Position for No.1 Piston" for the correct procedure.
2. Ensure that Tooling (C) is installed in Hole (Y) in the cylinder block. Use Tooling (C) in
order to lock the crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the
crankshaft during repairs.
3. Ensure that all of the components of the front gear group are clean and free from wear of
damage. If necessary, replace any components that are worn or damaged.
7/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 6 g02707196
8/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 7 g02707197
4. Install camshaft gear (1). Loosely install bolt (10) and washer (9) for the camshaft gear.
Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for the correct
procedure.
5. Install Tooling (B) through Hole (X) in camshaft gear (1) into the front housing.
9/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 8 g02707198
Illustration 9 g02707236
Alignment of timing marks
6. Install idler gear (8). Ensure that the timing mark on gear (1) and the timing mark on gear
(8) are aligned. Ensure that the mesh of the gears is correct. Tighten the bolts for idler gear
(8) to a torque of 44 N·m (32 lb ft). Refer to Disassembly and Assembly, "Idler Gear -
Remove and Install" for the correct procedure.
7. When bolt (9) is a 8.8 Grade. Tighten bolt (10) to a torque of 95 N·m (70 lb ft).
When bolt (9) is a 10.9 Grade. Tighten bolt (10) to a torque of 120 N·m (89 lb ft).
8. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly
and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
9. Install fuel injection pump gear (2). Ensure that the timing marks on gear (2) and the timing
marks on gear (8) are aligned. See Illustration 9. Ensure that the mesh of the gears is correct.
Refer to Disassembly and Assembly, "Fuel Injection Pump Gear - Install" for more
information.
10. Remove Tooling (B) and Tooling (C).
11. Use Tooling (D) in order to measure the end play of camshaft gear (1). Refer to
Specifications, "Camshaft" for more information.
10/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Use Tooling (D) in order to measure the backlash for gear (1), gear (2) and gear (8) is
within specified values. Refer to Specifications, "Gear Group (Front)" for further
information.
13. Adjust the engine valve lash. Refer to System Operation, Testing and Adjusting, "Engine
Valve Lash - Inspect/Adjust" for the correct procedure.
Illustration 10 g02707000
14. Install a new O-ring seal (3) to plug (4). Install plug (4) to the cylinder block. Tighten
locking bolt (5) against the spacer to a torque of 21 N·m (186 lb in).
15. Lubricate each gear with clean engine oil.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 11:36:36 UTC+0800 2020
11/11(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR ZCS
Configuration: 320D2 & 320D2 L Excavators ZCS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780467
Idler Gear - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter
C 230-6284 Timing Pin (Camshaft) 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump
Gear - Remove".
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
1/5(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel
pump gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02712440
Alignment of timing marks
2/5(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 2 g02712439
1. Remove plug (5) from the cylinder block. Remove O-ring seal (4) from plug (5).
2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston".
3. Install Tooling (B) into Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the
crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the
crankshaft during repairs.
4. Ensure that Tooling (C) is installed into Hole (X) in the camshaft gear. Use Tooling (C) in
order to lock the camshaft in the correct position.
5. Ensure that gear (1), gear (2), and gear (3) are marked in order to show alignment.
3/5(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 3 g02712442
6. Loosen nuts (7) on all rocker arms (8). Unscrew adjusters (6) on all rocker arms (8) until all
valves are fully closed.
Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between
the valves and pistons.
4/5(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 4 g02712444
7. Mark plate (9) in order to show orientation.
Note: Identification will ensure that the plate can be installed in the original orientation.
8. Remove bolts (10).
9. Remove plate (9).
10. Remove the assembly of idler gear (3) and hub (11) from the recess in the front housing.
Note: The idler gear must be tilted during removal.
11. Remove hub (11) from idler gear (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 11:37:32 UTC+0800 2020
5/5(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 L EXCAVATOR ZCS
Configuration: 320D2 & 320D2 L Excavators ZCS00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780466
Idler Gear - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
D
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
1/7(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02717945
1. If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the
compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top
Center Position for No.1 Piston" for the correct procedure.
2. Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in
order to lock the crankshaft in the correct position.
Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the
crankshaft during repairs.
2/7(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 2 g02712440
Alignment of timing marks
3. Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (1).
3/7(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 3 g02718564
4. Clean idler gear (3) and inspect the idler gear for wear or damage. Refer to Specifications,
"Gear Group (Front)" for more information. If necessary, replace the idler gear.
5. Clean hub (11) and inspect the hub for wear or damage. Refer to Specifications, "Gear
Group (Front)" for more information. If necessary, replace the hub.
6. Lubricate hub (11) with clean engine oil. Slide hub (11) into idler gear (3). Ensure that the
timing marks are toward the front of the idler gear.
4/7(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 4 g02718572
7. Align the timing mark on idler gear (3) with the timing mark on the camshaft gear. Refer to
the illustration 2. Install the assembly of idler gear (3) and hub (11) into the recess in the
timing case. Ensure that oil Hole (Z) is to the top of the hub.
Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are
aligned with the holes in the cylinder block.
8. Clean plate (9) and inspect the plate for wear or damage. If necessary, replace the plate.
9. Lubricate plate (9) with clean engine oil. Align the holes in plate (9) with the holes in hub
(11). Install the plate in the original orientation.
10. Install bolts (10).
11. Remove Tooling (B) and Tooling (C).
Note: Ensure that timing marks are aligned, before removing Tooling (B) and Tooling (C).
5/7(W)
w
2020/1/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

More Related Content

More from rong74gou

Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...rong74gou
 
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...rong74gou
 
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...rong74gou
 
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...rong74gou
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...rong74gou
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...rong74gou
 
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...rong74gou
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...rong74gou
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...rong74gou
 
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...rong74gou
 
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...rong74gou
 
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...rong74gou
 
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...rong74gou
 
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...rong74gou
 
Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...
Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...
Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...rong74gou
 
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...rong74gou
 
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...rong74gou
 
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...rong74gou
 
Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...
Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...
Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...rong74gou
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...rong74gou
 

More from rong74gou (20)

Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
 
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
 
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
 
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
Caterpillar Cat 426C Backhoe Loader (Prefix 1NR) Service Repair Manual (1NR01...
 
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
Caterpillar Cat 426C Backhoe Loader (Prefix 1ER) Service Repair Manual (1ER00...
 
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
Caterpillar Cat 420F2 BACKHOE LOADER (Prefix NSB) Service Repair Manual (NSB0...
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LYC) Service Repair Manual (LYC0...
 
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
Caterpillar Cat 420F2 Backhoe Loader (Prefix LBS) Service Repair Manual (LBS0...
 
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
Caterpillar Cat 320D2 L Excavator (Prefix YBK) Service Repair Manual (YBK0000...
 
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix YBK) Service Repair Manual (YBK00001 ...
 
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
Caterpillar Cat 305.5E Mini Hydraulic Excavator (Prefix MX5) Service Repair M...
 
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix FR3) Service Repair M...
 
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...
Caterpillar Cat 303ECR Mini Hydraulic Excavator (Prefix CK3) Service Repair M...
 
Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...
Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...
Caterpillar Cat 303E CR Mini Hydraulic Excavator (Prefix SMG) Service Repair ...
 
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix CR9) Service Repa...
 
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...
Caterpillar Cat 303.5E2 CR Mini Hydraulic Excavator (Prefix AC5) Service Repa...
 
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...
Caterpillar Cat 303.5E Mini Hydraulic Excavator (Prefix RSE) Service Repair M...
 
Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...
Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...
Caterpillar Cat 301.7D Mini Hydraulic Excavator (Prefix LJH) Service Repair M...
 
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
Caterpillar Cat 140H Motor Grader (Prefix 8JM) Service Repair Manual (8JM0000...
 

Recently uploaded

ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILESABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILESsriharshaganjam1
 
Mastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX ResidentsMastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX ResidentsRowlett Motorwerks
 
Human Resource Practices TATA MOTORS.pdf
Human Resource Practices TATA MOTORS.pdfHuman Resource Practices TATA MOTORS.pdf
Human Resource Practices TATA MOTORS.pdfAditiMishra247289
 
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!Mint Automotive
 
Control-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAGControl-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAGVikrantPawar37
 
Welcome to Auto Know University Orientation
Welcome to Auto Know University OrientationWelcome to Auto Know University Orientation
Welcome to Auto Know University Orientationxlr8sales
 
Lighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light ServiceLighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light ServiceImport Car Center
 
A Comprehensive Exploration of the Components and Parts Found in Diesel Engines
A Comprehensive Exploration of the Components and Parts Found in Diesel EnginesA Comprehensive Exploration of the Components and Parts Found in Diesel Engines
A Comprehensive Exploration of the Components and Parts Found in Diesel EnginesROJANE BERNAS, PhD.
 
怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道
怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道
怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道7283h7lh
 
Pros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptxPros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptxjennifermiller8137
 

Recently uploaded (10)

ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILESABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
ABOUT REGENERATIVE BRAKING SYSTEM ON AUTOMOBILES
 
Mastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX ResidentsMastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
Mastering Mercedes Engine Care Top Tips for Rowlett, TX Residents
 
Human Resource Practices TATA MOTORS.pdf
Human Resource Practices TATA MOTORS.pdfHuman Resource Practices TATA MOTORS.pdf
Human Resource Practices TATA MOTORS.pdf
 
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
Can't Roll Up Your Audi A4 Power Window Let's Uncover the Issue!
 
Control-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAGControl-Plan-Training.pptx for the Automotive standard AIAG
Control-Plan-Training.pptx for the Automotive standard AIAG
 
Welcome to Auto Know University Orientation
Welcome to Auto Know University OrientationWelcome to Auto Know University Orientation
Welcome to Auto Know University Orientation
 
Lighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light ServiceLighting the Way Understanding Jaguar Car Check Engine Light Service
Lighting the Way Understanding Jaguar Car Check Engine Light Service
 
A Comprehensive Exploration of the Components and Parts Found in Diesel Engines
A Comprehensive Exploration of the Components and Parts Found in Diesel EnginesA Comprehensive Exploration of the Components and Parts Found in Diesel Engines
A Comprehensive Exploration of the Components and Parts Found in Diesel Engines
 
怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道
怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道
怎么办理美国UCONN毕业证康涅狄格大学学位证书一手渠道
 
Pros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptxPros and cons of buying used fleet vehicles.pptx
Pros and cons of buying used fleet vehicles.pptx
 

Caterpillar Cat 320D2 Excavator (Prefix ZCS) Service Repair Manual (ZCS00001 and up).pdf

  • 1. Service Repair Manual Models 320D2 and 320D2 L Excavator
  • 2. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR ZCS Configuration: 320D2 & 320D2 L Excavators ZCS00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780462 Gear Group (Front) - Remove and Install SMCS - 1206-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A(1) 9U-6198 Crankshaft Turning Tool 1 A(2) 9U-7336 Housing 1 5P-7305 Engine Turning Tool 1 B 230-6284 Timing Pin (Camshaft) 1 C 136-4632 Timing Pin (Crankshaft) 1 268-1966 Adapter 1 (1) The Crankshaft Turning Tool is used on the front pulley. (2) This Tool is used in the aperture for the electric starting motor. Start By: a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure . b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure . NOTICE 1/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 3. Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Dispose of all fluids according to local regulations and mandates. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. Illustration 1 g02706996 2/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 4. Illustration 2 g02695979 1. Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the front gear group. Carefully follow the procedure in order to remove the gear group. 2. Remove plug (4) from the cylinder block. Remove O-ring seal (3) from plug (4). 3. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. 4. Install Tooling (B) through Hole (X) in camshaft gear (1) into the front housing. Use Tooling (B) in order to lock the camshaft in the correct position. 5. Install Tooling (C) into Hole (Y) in the cylinder block. Use Tooling (C) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the crankshaft during repairs. 6. Apply sufficient pressure to fuel injection pump gear (2) in a counterclockwise direction in order to remove the backlash. Lock the fuel injection pump in this position. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure. 3/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 5. Illustration 3 g02707118 7. Loosen nuts (6) on all rocker arms (7). Unscrew adjusters (5) on all rocker arms (7) until all valves are fully closed. Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons. 4/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 6. Illustration 4 g02706997 Alignment of timing marks 8. Mark gear (1), gear (2), and gear (8) in order to show alignment. Refer to Illustration 4. Note: Identification will ensure that the gears can be installed in the original alignment. 9. Remove fuel pump gear (2). Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove and Install" for the correct procedure. 10. Remove camshaft gear (1). Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for the correct procedure. 11. Remove idler gear (8). Refer to Disassembly and Assembly, "Idler Gear - Remove and Install" for the correct procedure. Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A(1) 9U-6198 Crankshaft Turning Tool 1 A(2) 9U-7336 Housing 1 5/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 7. 5P-7305 Engine Turning Tool 1 C 136-4632 Timing Pin (Crankshaft) 1 268-1966 Adapter 1 B 230-6284 Timing Pin (Camshaft) 1 D 9U-7324 Indicator Bracket 1 7H-1942 Dial Indicator 1 3S-3268 Indicator Contact Point 1 7H-1940 Universal Attachment 1 (1) The Crankshaft Turning Tool is used on the front pulley. (2) This Tool is used in the aperture for the electric starting motor. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the fuel injection pump. 6/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 8. Illustration 5 g02706999 1. If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. 2. Ensure that Tooling (C) is installed in Hole (Y) in the cylinder block. Use Tooling (C) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the crankshaft during repairs. 3. Ensure that all of the components of the front gear group are clean and free from wear of damage. If necessary, replace any components that are worn or damaged. 7/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 10. Illustration 7 g02707197 4. Install camshaft gear (1). Loosely install bolt (10) and washer (9) for the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for the correct procedure. 5. Install Tooling (B) through Hole (X) in camshaft gear (1) into the front housing. 9/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 11. Illustration 8 g02707198 Illustration 9 g02707236 Alignment of timing marks 6. Install idler gear (8). Ensure that the timing mark on gear (1) and the timing mark on gear (8) are aligned. Ensure that the mesh of the gears is correct. Tighten the bolts for idler gear (8) to a torque of 44 N·m (32 lb ft). Refer to Disassembly and Assembly, "Idler Gear - Remove and Install" for the correct procedure. 7. When bolt (9) is a 8.8 Grade. Tighten bolt (10) to a torque of 95 N·m (70 lb ft). When bolt (9) is a 10.9 Grade. Tighten bolt (10) to a torque of 120 N·m (89 lb ft). 8. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install" for the correct procedure. 9. Install fuel injection pump gear (2). Ensure that the timing marks on gear (2) and the timing marks on gear (8) are aligned. See Illustration 9. Ensure that the mesh of the gears is correct. Refer to Disassembly and Assembly, "Fuel Injection Pump Gear - Install" for more information. 10. Remove Tooling (B) and Tooling (C). 11. Use Tooling (D) in order to measure the end play of camshaft gear (1). Refer to Specifications, "Camshaft" for more information. 10/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 12. 12. Use Tooling (D) in order to measure the backlash for gear (1), gear (2) and gear (8) is within specified values. Refer to Specifications, "Gear Group (Front)" for further information. 13. Adjust the engine valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure. Illustration 10 g02707000 14. Install a new O-ring seal (3) to plug (4). Install plug (4) to the cylinder block. Tighten locking bolt (5) against the spacer to a torque of 21 N·m (186 lb in). 15. Lubricate each gear with clean engine oil. End By: a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure. b. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Jan 6 11:36:36 UTC+0800 2020 11/11(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 13. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR ZCS Configuration: 320D2 & 320D2 L Excavators ZCS00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780467 Idler Gear - Remove SMCS - 1206-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A(1) 9U-6198 Crankshaft Turning Tool 1 A(2) 5P-7306 Housing 1 5P-7305 Engine Turning Tool 1 B 136-4632 Timing Pin (Crankshaft) 1 268-1966 Adapter C 230-6284 Timing Pin (Camshaft) 1 (1) The Crankshaft Turning Tool is used on the front pulley. (2) This Tool is used in the aperture for the electric starting motor. Start By: a. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove". b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. 1/5(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 14. Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel pump gear. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g02712440 Alignment of timing marks 2/5(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 15. Illustration 2 g02712439 1. Remove plug (5) from the cylinder block. Remove O-ring seal (4) from plug (5). 2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston". 3. Install Tooling (B) into Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs. 4. Ensure that Tooling (C) is installed into Hole (X) in the camshaft gear. Use Tooling (C) in order to lock the camshaft in the correct position. 5. Ensure that gear (1), gear (2), and gear (3) are marked in order to show alignment. 3/5(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 16. Illustration 3 g02712442 6. Loosen nuts (7) on all rocker arms (8). Unscrew adjusters (6) on all rocker arms (8) until all valves are fully closed. Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons. 4/5(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 17. Illustration 4 g02712444 7. Mark plate (9) in order to show orientation. Note: Identification will ensure that the plate can be installed in the original orientation. 8. Remove bolts (10). 9. Remove plate (9). 10. Remove the assembly of idler gear (3) and hub (11) from the recess in the front housing. Note: The idler gear must be tilted during removal. 11. Remove hub (11) from idler gear (3). Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Jan 6 11:37:32 UTC+0800 2020 5/5(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 18. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320D2 L EXCAVATOR ZCS Configuration: 320D2 & 320D2 L Excavators ZCS00001-UP (MACHINE) POWERED BY C7.1 Engine Disassembly and Assembly C7.1 (Mech) Engines for Caterpillar Built Machines Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017 i04780466 Idler Gear - Install SMCS - 1206-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A(1) 9U-6198 Crankshaft Turning Tool 1 A(2) 5P-7306 Housing 1 5P-7305 Engine Turning Tool 1 B 230-6284 Timing Pin (Camshaft) 1 C 136-4632 Timing Pin (Crankshaft) 1 268-1966 Adapter 1 D 9U-7324 Indicator Bracket 1 7H-1942 Dial Indicator 1 3S-3268 Indicator Contact Point 1 7H-1940 Universal Attachment 1 (1) The Crankshaft Turning Tool is used on the front pulley. (2) This Tool is used in the aperture for the electric starting motor. NOTICE Keep all parts clean from contaminants. 1/7(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 19. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 20. Contaminants may cause rapid wear and shortened component life. Illustration 1 g02717945 1. If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. 2. Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs. 2/7(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 21. Illustration 2 g02712440 Alignment of timing marks 3. Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (1). 3/7(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 22. Illustration 3 g02718564 4. Clean idler gear (3) and inspect the idler gear for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the idler gear. 5. Clean hub (11) and inspect the hub for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the hub. 6. Lubricate hub (11) with clean engine oil. Slide hub (11) into idler gear (3). Ensure that the timing marks are toward the front of the idler gear. 4/7(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 23. Illustration 4 g02718572 7. Align the timing mark on idler gear (3) with the timing mark on the camshaft gear. Refer to the illustration 2. Install the assembly of idler gear (3) and hub (11) into the recess in the timing case. Ensure that oil Hole (Z) is to the top of the hub. Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are aligned with the holes in the cylinder block. 8. Clean plate (9) and inspect the plate for wear or damage. If necessary, replace the plate. 9. Lubricate plate (9) with clean engine oil. Align the holes in plate (9) with the holes in hub (11). Install the plate in the original orientation. 10. Install bolts (10). 11. Remove Tooling (B) and Tooling (C). Note: Ensure that timing marks are aligned, before removing Tooling (B) and Tooling (C). 5/7(W) w 2020/1/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...