Caterpillar Cat 365B L EXCAVATOR (Prefix 4XZ) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
365B L EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B L EXCAVATOR 4XZ
Configuration: ISJ HEX COMMONALITY CHART 4XZ00001-UP (MACHINE)
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i01492295
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 1P-1864 Pliers 1
(B) 1P-1858 Pliers 1
(C) 138-7575 Link Bracket 2
(D) 1P-0520 Driver Group 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove
and Install " in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/18
ISJ HEX COMMONALITY CHART 4XZ00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/11/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00574938
1. Thoroughly clean the outside of travel motor (1) prior to disassembly. Weight of the travel
motor is 118 kg (260 lb).
2. Place an alignment mark across all housings of the travel motor for assembly purposes.
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2/18
2020/11/19

3. Remove two socket head bolts (2) from brake cover (3) that are 180 degrees from each
other. Replace these two bolts with bolts (4) that are slightly longer in length. The two
longer bolts will retain the brake cover when the remaining ten socket head bolts (2) are
removed.
4. Carefully remove the ten remaining socket head bolts (2) that retain the brake cover in
position.
5. Remove two longer bolts (4) from the brake cover.
6. Remove two remaining hex head bolts (5) from brake cover (3) .
7. Remove brake cover (3) from the head assembly.
8. If necessary, remove the brake adjusting screws (6) from brake cover (3) .
3/18
2020/11/19

Note: There is an inner spring and an outer spring in each spring set.
9. Remove twenty-four spring sets from the brake and piston assembly.
10. Remove brake assembly (9) from head assembly (8) .
4/18
2020/11/19

11. Remove ring (10) from brake assembly (9) .
12. Remove retainer plate (11) from brake assembly (9) .
5/18
2020/11/19

13. Remove external discs (12) and internal plates (13) from brake assembly (9) .
14. Remove piston (14) from brake assembly (9) .
15. Remove seal (15) from piston (14) .
6/18
2020/11/19

16. Remove O-rings (16) and (17) .
17. Remove retaining ring (18) from the shaft of the motor assembly. Remove gear (19) .
18. Use Tool (A) to remove retainer ring (21) .
Note: Measure the position of the rod assembly before removing. The nut and the rod
assembly must be returned to the original location at assembly.
19. Remove the nut and bushing (20) from the rod assembly.
20. Remove four socket head bolts (22) from head assembly (8) .
7/18
2020/11/19

21. Attach Tooling (C) and a suitable lifting device to head assembly (8). Carefully remove the
head assembly from the motor assembly. Weight of the head assembly is 244.7 N (55 lb).
Note: The port plate can remain with the pump housing when the head assembly is
removed.
22. Remove port plate (23) from head assembly (8) .
8/18
2020/11/19

23. Remove plug (24) from head assembly (8) .
24. Remove check valve assembly (25) from head assembly (8) .
25. Remove stem (30) from check valve (25) .
26. Remove seat (26), spring (27), guide (28), and seal (29) from stem (30) .
9/18
2020/11/19

27. If necessary, remove pin (31) from the head assembly (8) .
28. Remove O-ring seal (32) from the head assembly.
29. Use Tooling (D) and a hammer to remove bearing (33) and seal (34) from the bore of the
head assembly.
Note: The port plate can remain with the head assembly when the head assembly is
removed from the pump housing.
30. Remove rod assembly (35) from motor housing (37). If necessary, remove port plate (23).
Remove O-ring seal (36).
10/18
ISJ HEX COMMONALITY CHART 4XZ00001-UP (MACHINE)(SEBP5600 - 00)...
2020/11/19

Note: Barrel assembly must remain intact during removal.
31. Position motor housing (37) sideways. Carefully remove barrel assembly (38) .
32. Place identification marks on piston assemblies (39), retainer (40), and barrel (38). These
components must be reinstalled in the original location.
11/18
2020/11/19

33. Remove piston assemblies (39) and retainer (40) from barrel (38) .
34. Remove piston assemblies (39) from retainer (40) .
12/18
2020/11/19

35. Remove guide (41), shims (42), and spring assembly (43) from barrel (38) .
36. Use Tooling (B) to remove retaining ring (44) from shaft assembly (45) and motor housing
(37) .
13/18
2020/11/19

37. Use a soft hammer to drive shaft assembly (45) from motor housing (37) .
38. Remove cover (46) from shaft assembly (45) .
39. Remove seal (47) from cover (46) .
14/18
2020/11/19

40. Use Tool (A) to remove retaining ring (48) from shaft assembly (45) .
41. Use a press to remove bearing (49) and spacer (50) from shaft (45) .
15/18
2020/11/19

42. Remove swashplate (51) from motor housing (37) .
43. Remove plate (52) from swashplate (51) .
16/18
2020/11/19

44. Remove machine screws (53). Remove retainer plate (54) and plunger (55) from swashplate
(51) .
45. If necessary, remove stopper (56) and pin (57) from swashplate (51) .
46. Remove valve cartridge (58) from motor housing (37) .
47. Remove two pistons (59) from the motor housing.
48. Remove the two machine screws (60) and bearings (61) from the motor housing.
17/18
2020/11/19

49. Remove seal (62) from rod assembly (35) .
50. Remove rings (64) from valve cartridge (66) .
51. Remove seals (63) and (65) from the valve cartridge.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 19 12:04:19 UTC+0800 2020
18/18
2020/11/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B L EXCAVATOR 4XZ
Configuration: ISJ HEX COMMONALITY CHART 4XZ00001-UP (MACHINE)
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i01492280
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 1P-1864 Pliers 1
(B) 1P-1858 Pliers 1
(C) 138-7575 Link Bracket 2
(D) 1P-0520 Driver Group 1
(E) 141-4803 Gauge Block 1
(F) 6V-2021 Depth Gauge 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of "10W" oil to all components before assembly.
1/20
2020/11/19

1. Install seals (63) and (65 ) on valve cartridge (66) .
2. Install rings (64) on the valve cartridge.
3. Install seal (62) on rod assembly (35) .
2/20
2020/11/19

4. Install bearings (61) in motor housing (37).
5. Apply 9S-3263 Thread Lock Compound to two machine screws (60). Install the machine
screws in motor housing (37) and tighten to a torque of 5 N·m (44 lb in).
6. Install two pistons (59) in motor housing (37) .
7. Install valve cartridge (58) in the motor housing.
8. Install stopper (56) and pin (57) in swashplate (51) .
9. Install rods (55) and retainer plate (54) in swashplate (51) .
10. Apply 9S-3263 Thread Lock Compound to machine screws (53). Install the machine screws
in the retainer plate and the swashplate. Tighten the machine screws to a torque of 5 N·m
(45 lb in).
3/20
2020/11/19

11. Install plate (52) on swashplate (51) .
12. Carefully install swashplate assembly (51) in motor housing (37) .
4/20
2020/11/19

13. Install spacer (50) on shaft (45) .
14. Raise the temperature of bearing (49) to 135 °C (275 °F). Install the bearing on the shaft.
15. Use Tool (A) to install retaining ring (48) on shaft assembly (45) .
5/20
2020/11/19

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

16. Install seal (47) on cover (46) .
17. Install cover (46) on shaft assembly (45) .
18. Install shaft assembly (45) in motor housing (37) .
6/20
2020/11/19

Caterpillar Cat 365B L EXCAVATOR (Prefix 4XZ) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 365B L EXCAVATOR (Prefix 4XZ) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 365B L EXCAVATOR (Prefix 4XZ) Service Repair Manual Instant Download.pdf (20)

More from jiuliu14811471

More from jiuliu14811471 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 365B L EXCAVATOR (Prefix 4XZ) Service Repair Manual Instant Download.pdf