Slideshare uses cookies to improve functionality and performance, and to provide you with relevant advertising. If you continue browsing the site, you agree to the use of cookies on this website. See our User Agreement and Privacy Policy.

Slideshare uses cookies to improve functionality and performance, and to provide you with relevant advertising. If you continue browsing the site, you agree to the use of cookies on this website. See our Privacy Policy and User Agreement for details.

Like this presentation? Why not share!

No Downloads

Total views

4,110

On SlideShare

0

From Embeds

0

Number of Embeds

41

Shares

0

Downloads

96

Comments

0

Likes

3

No embeds

No notes for slide

- 1. Calorimetry Measurement of Enthalpy Change
- 2. <ul><li>Specific heat capacity is the amount of heat needed to raise the temperature of 1g of substance by 1K </li></ul><ul><li>Specific heat capacity of water = 4.18 KJ kg -1 K -1 </li></ul><ul><li>or 4.18 J g -1 K 1 </li></ul><ul><li>Be careful with the units it could also be quoted as KJ g -1 K -1 </li></ul><ul><li>Ensure you use the correct units in your calculation! </li></ul><ul><li>To measure the heat released in a process we arrange for the heat to be transferred to a substance (usually water) then measure the temperature rise. </li></ul>
- 3. <ul><li>Then : </li></ul><ul><li> H = mass of water x specific heat capacity x temp rise </li></ul><ul><li> H = m x c x T </li></ul><ul><li>Note m = mass of water not mass of any solids present </li></ul>
- 4. <ul><li>Measuring Enthalpy Changes in the Laboratory </li></ul><ul><li>Apparatus needed </li></ul><ul><li>An insulated container to serve as a calorimeter </li></ul><ul><li>A thermometer </li></ul><ul><li>A balance </li></ul><ul><li>Volumetric appaaratus (e.g burette, pipette, measuring cylinder) </li></ul>
- 5. A simple calorimeter
- 7. <ul><li>Some general steps in the procedure </li></ul><ul><li>Allow a known mass or volume of reactants to reach the temperature of the surroundings </li></ul><ul><li>2) Thoroughly mix the reactants and record the highest or lowest temperature reached </li></ul><ul><li>Determine the temperature change for the reaction </li></ul><ul><li>Calculate the enthalpy change for the reaction </li></ul><ul><li>For a given mass (m kg) of reacting substance the heat energy released is calculated using the equation </li></ul><ul><li>Heat = m x c x T </li></ul>
- 8. <ul><li>Assumptions and Errors </li></ul><ul><li>For aqueous solutions we assume that 1ml has a mass of 1g and that for dilute solutions the specific heat capacity is the same as that of water. </li></ul><ul><li>These assumptions will give minor errors in our calculations </li></ul><ul><li>The biggest error will be heat lost to the surroundings (i.e to the thermometer, the surrounding air and the container) This can be minimised by the use of an adequately insulated calorimeter </li></ul>
- 9. <ul><li>Excess powdered zinc was added to 100ml of 0.2 mol/L copper (II) sulphate solution. A temperature rise of 10 o C was recorded. Find the enthalpy change for the reaction. </li></ul><ul><li> H = m x c x T </li></ul><ul><li> H = 100 g x 4.18 KJ kg -1 K -1 x 10 KJ </li></ul><ul><li>1000 </li></ul><ul><li>= 4.180 KJ </li></ul><ul><li>This is for the no of moles of CuSO 4 used in the experiment </li></ul><ul><li>No of moles of CuSO 4 = 0.2 x 100 = 0.02 moles </li></ul><ul><li>1000 </li></ul><ul><li> H = 4.180 = 209 KJ mol -1 </li></ul><ul><li>0.02 </li></ul><ul><li>The reaction is exothermic so we need to put in a negative sign </li></ul><ul><li> H r = - 209 KJ mol -1 </li></ul><ul><li>Note We do not use the standard sign as standard conditions were not used. </li></ul>
- 10. <ul><li>Combustion </li></ul><ul><li>To find the heat of combustion of a substance a known mass of the substance is burned, the heat released transferred to water and the enthalpy change found as before </li></ul>
- 11. <ul><li>In an experiment to find the heat of combustion of ethanol the following results were obtained </li></ul><ul><li>Initial mass of lamp + ethanol = 65.20g </li></ul><ul><li>Final mass of lamp = 64.28g </li></ul><ul><li>Final temperature of water = 47.1 o C </li></ul><ul><li>Initial temperature of water = 28.5 o C </li></ul><ul><li>Mass of the water = 300g </li></ul><ul><li>What are the products of complete combustion of ethanol? </li></ul><ul><li>What mass of ethanol was burnt? How many moles is this? </li></ul><ul><li>What quantity of heat was transferred to the water? </li></ul><ul><li>Find H c of ethanol </li></ul><ul><li>Identify any sources of error </li></ul><ul><li>Is ethanol a good fuel? </li></ul>
- 12. <ul><li>C 2 H 5 OH + 3O 2 2CO 2 + 3H 2 O </li></ul><ul><li> H = 300 x 4.18 KJ kg -1 K -1 x 18.6K = 23.3KJ </li></ul><ul><li>1000 </li></ul><ul><li>Mass of ethanol used = 0.92g </li></ul><ul><li>0.92g = 0.92 = 0.02 mol </li></ul><ul><li>46 </li></ul><ul><li> H c = - 23.3 = -1160 KJ/mol </li></ul><ul><li>0.02 </li></ul>
- 13. <ul><li>Errors </li></ul><ul><li>Heat lost to surroundings (air, can thermometer) </li></ul><ul><li>Errors in measuring temperature change (unavoidable error in reading thermometer) </li></ul><ul><li>Errors in measuring masses (unavoidable error in reading balance) </li></ul><ul><li>The enthalpy change of combustion is high ethanol is a good fuel </li></ul>

No public clipboards found for this slide

×
### Save the most important slides with Clipping

Clipping is a handy way to collect and organize the most important slides from a presentation. You can keep your great finds in clipboards organized around topics.

Be the first to comment