Eng Puetne De Tubos

1,977 views

Published on

Published in: Education, Technology
0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total views
1,977
On SlideShare
0
From Embeds
0
Number of Embeds
1,538
Actions
Shares
0
Downloads
62
Comments
0
Likes
1
Embeds 0
No embeds

No notes for slide

Eng Puetne De Tubos

  1. 1. A platform that can be raised
  2. 2. A platform that can be raised <ul><li>We are going to make a bridge with a platform that can be raised. The structure will be made with triangles of paper only </li></ul>
  3. 3. <ul><li>Before we start with the bridge we are going to do a resistance test on the traingulated structures </li></ul>Triangles resistance test
  4. 4. <ul><li>In order to do this project we need these materials: </li></ul><ul><li>Paper </li></ul><ul><li>Thermofuse glue </li></ul><ul><li>Cord </li></ul><ul><li>Plywood </li></ul>Triangle resistance test
  5. 5. <ul><li>First of all we will make the paper tubes. You roll the paper around a wood bar. </li></ul>Triangles resistance test
  6. 6. <ul><li>Then glue the edge with a little glue. Take care because if you use too much, it will get stuck to the </li></ul>Triangles resistance test
  7. 7. <ul><li>Since our tower is 30cm high we have to make: </li></ul><ul><ul><li>4 tubes 30cm long </li></ul></ul><ul><ul><li>16 tubes 10 cm long </li></ul></ul><ul><ul><li>16 tubes de 13 cm long </li></ul></ul>Triangles resistance test 4x 30cm 16x13cm 16x10cm
  8. 8. <ul><li>With the tubes you will form two sides of the tower </li></ul>Triangles resistance test Make two of these 30cm 10cm 13cm
  9. 9. <ul><li>In order to connect the bars properly try to make a gap at the end of the shortest bars </li></ul>Triangles resistance test
  10. 10. <ul><li>Once you have two sides you can start joining them together like in the picture </li></ul>Triangles resistance test 2X
  11. 11. <ul><li>Remember that the more triangles the stronger the structures will be </li></ul>Triangles resistance test
  12. 12. Triangles resistance test <ul><li>Finally we will put all the towers together to make them more resistant. </li></ul><ul><li>The board has to be 30x40cm in order to cover 6 towers </li></ul>
  13. 13. Triangles resistance test <ul><li>We will check the resistance of our triangles¡¡ </li></ul>
  14. 14. Triangles resistance test <ul><li>You have only six days to finish it, so </li></ul><ul><li>Let’s work </li></ul>
  15. 15. A platform that can be raised <ul><li>Now that we know how to make triangulated structures we are able to build a platform that can be raised </li></ul>
  16. 16. <ul><li>As you did before, o nce you have two sides you can start joining them together like in the picture </li></ul>Triangles resistance test 2X
  17. 17. A platform that can be raised <ul><li>Attention¡¡¡¡¡ </li></ul><ul><li>This time we have to leave a gap where the platform will be placed </li></ul>
  18. 18. A platform that can be raised <ul><li>This is the handle that will move our platform </li></ul>20cm 3cm 8cm 5cm
  19. 19. A platform that can be raised <ul><li>The platform has to be 20x10cm and you have to make it as you did before </li></ul>Cover it with a piece of paper 10cm 13cm 20cm
  20. 20. A platform that can be raised <ul><li>The platform form will be made with tubes and has to be movable, so make sure that one tube can be placed inside the other </li></ul>5cm
  21. 21. A platform that can be raised <ul><li>Then you need to insert the crank inside the tower, using two tubes of 3cm diameter </li></ul>Cranck
  22. 22. A platform that can be raised <ul><li>Finally you only need to connect the platform to the tower with a cord, making a knot at both ends </li></ul>

×