The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
The Future of Autonomous Vehicles | civilthings.com | Detailed informationgettygaming1
civilthings.com Present Autonomous vehicles, also known as self-driving cars, represent a groundbreaking advancement in transportation technology. These vehicles utilize sophisticated sensors, advanced software, and machine learning algorithms to navigate roads and transport passengers without human intervention. Major companies in the autonomous vehicle industry are investing heavily in the development and testing of these innovative machines, aiming to enhance safety, efficiency, and convenience on the roads.
The autonomous vehicle market is rapidly expanding, driven by technological progress and increasing consumer interest. With the advent of autonomous vehicle technology, the future of transportation promises significant changes, including reduced traffic accidents and lower emissions. However, the widespread adoption of autonomous vehicles faces challenges, such as regulatory hurdles, safety concerns, and public acceptance.
Autonomous vehicle regulations and legislation are evolving to address these issues, ensuring that the integration of self-driving cars into everyday life is smooth and secure. As the industry grows, news and trends related to autonomous vehicles continue to capture global attention. From the development of cutting-edge sensors to advancements in autonomous vehicle software, this sector is poised to revolutionize how we think about mobility.
Stay informed about the latest in autonomous vehicle technology, industry developments, and market trends to understand the profound impact these vehicles will have on our future.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 208-6033 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the thoroughly
clean the exterior of the component. This will prevent dirt from entering the internal
mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
2/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00708089
2. Fasten the final drive to Tooling (A) , as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2) , as shown. Remove the cover. The weight of the cover is approximately 32 kg (70
lb).
3/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00879362
5. Remove bolts (3) . Remove gear (5) . Check plate (6) . Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2) .
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4) .
Illustration 5 g00780428
4/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 7. Remove gear (8) . Remove spacer (9) .
Illustration 6 g00780432
8. Remove retaining ring (10) with Tooling (C) . Remove washer (11) . Remove gear (12) .
Remove bearing assembly (13) . Remove second washer (11) .
9. Repeat Step 8 for the remaining two gear assemblies.
Illustration 7 g00781401
10. Remove retaining ring (14) .
5/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00781407
11. Remove carrier assembly (15) .
Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15) .
6/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 16. Disassemble carrier assembly (19) , as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21) .
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24) .
17. Repeat Steps 16.a through 16.e for the other two planetary.
8/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 15 g00781529
18. Remove gear (25) . Remove spacer (26) .
Illustration 16 g00781559
19. Remove carrier assembly (27) .
20. Use two people to remove carrier assembly (27) . The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27) , as follows.
9/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28) .
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
22. Repeat Steps 21.a through 21.e for the other two planetary gears.
10/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 20 g00781730
23. Use two people to remove gear (33) . The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34) .
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B) .
11/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35) .
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35) . Use Tooling (D) to remove stopper plate (35) .
12/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36) . The weight of
housing (36) is approximately 100 kg (220 lb).
Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38) .
Illustration 27 g01147975
13/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36) .
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36) .
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 14:05:20 UTC+0800 2020
14/14(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR ERN
Configuration: 330D Excavator ERN00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06252413
Final Drive - Disassemble - Type-Two
SMCS - 4050-015
S/N - B6H568-UP
S/N - DTS1-UP
S/N - EAH1-UP
S/N - EDX1-UP
S/N - EFT1-UP
S/N - ERN275-UP
S/N - FAR1-UP
S/N - FFK1-UP
S/N - GGE1-UP
S/N - GGH1-UP
S/N - HHK1-UP
S/N - J2F1-UP
S/N - JBT1-UP
S/N - JLP299-UP
S/N - JTN1-UP
S/N - JWR1-UP
1/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. S/N - XBH1-UP
S/N - YCF1-UP
S/N - ZCT1-UP
S/N - ZML1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description QTY
A 439-3940 Link Brackets 3
B 439-3939 Link Bracket 2
C 154-6183 Forcing Bolts 3
Start By:
A. Remove the final drive and the travel motor.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
Illustration 1 g02151790
Note: The weight of the entire final drive assembly is approximately 550 kg (1200 lb).
2. Attach Tooling (A) and a suitable lifting device to cover (2) . The weight of cover (2) is
approximately 32 kg (70 lb). Remove bolts (1) and cover (2) .
3/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g00879362
3. Remove bolts (3) . Remove gear (5) . Remove plate (6) . Remove plugs (4) from cover (2) .
Illustration 3 g00879365
4. Remove O-ring seal (7) from plugs (4) .
4/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 4 g02151806
5. Remove sun gear (8) , spacer (9) , and planetary gear assembly (10) .
Illustration 5 g02151809
6. Remove retaining ring (11) , washer (12) , planetary gear (13) , roller bearing (15) , and
washer (16) from carrier assembly (17) .
7. Repeat Step 6 for the remaining two gear assemblies.
8. Remove retaining ring (14) and sun gear (18) from carrier assembly (17) .
5/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 6 g02152150
9. Use a suitable press to remove the shafts from carrier assembly (17) .
Illustration 7 g02151813
10. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (19) . The
weight of planetary gear assembly (19) is approximately 48 kg (105 lb). Remove planetary
gear assembly (19) .
11. Remove spacer (20) .
6/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 8 g02151782
12. Drive spring pin (21) into planetary shaft (22) with a suitable hammer and a suitable punch.
13. Remove planetary shaft (22) , washer (24) , roller bearing (25) , planetary gear (26) , and
washer (27) from the planetary gear assembly (19) .
14. Remove spring pin (21) from planetary shaft (22) with a suitable hammer and a suitable
punch.
15. Remove retaining ring (23) and sun gear (28) from planetary gear assembly (19) .
Illustration 9 g02152208
7/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 16. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (29) . The
weight of planetary gear assembly (29) is approximately 38 kg (85 lb). Remove planetary
gear assembly (29) .
Illustration 10 g02152467
17. Drive spring pin (30) into planetary shaft (31) with a suitable hammer and a suitable punch.
18. Remove planetary shaft (31) , washer (32) , roller bearings (33) , planetary gear (34) , and
washer (35) from the planetary gear assembly (29) .
19. Remove spring pin (30) from planetary shaft (31) with a suitable hammer and a suitable
punch.
8/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 11 g02152399
20. Attach Tooling (A) and a suitable lifting device to ring gear (36) . The weight of ring gear
(36) is approximately 66 kg (146 lb). Remove ring gear (36) .
21. Remove O-ring seal (37) from sprocket housing (38) .
Illustration 12 g02152525
Illustration 13 g02152528
Note: Mark the orientation of coupling gear (40) for assembly purposes.
22. Remove bolts (39) from coupling gear (40) . Use Tooling (C) in order to remove coupling
gear (40) from the motor housing.
9/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 14 g02152546
23. Remove shims (41) from the motor housing.
Illustration 15 g02152552
Note: Upper bearing cone (42) and lower bearing cone (43) are a slip fit on the motor
housing. While you remove sprocket housing (38) from the motor housing, upper bearing
cone (42) may stay with the sprocket housing, or upper bearing cone (42) may stay on the
motor housing.
24. Attach Tooling (B) and a suitable lifting device to sprocket housing (38) . The weight of
sprocket housing (38) is approximately 109 kg (240 lb). Remove sprocket housing (38) and
upper bearing cone (42) .
10/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 16 g02152595
25. Remove dowels (45) from the motor housing.
26. Remove Duo-Cone seal (44) from the motor housing.
27. If lower bearing cone (43) remained on the motor housing, then remove the lower bearing
cone.
Illustration 17 g02152598
28. Remove Duo-Cone seal (46) from the sprocket housing.
29. If upper bearing cone (42) remained on the sprocket housing, then remove the upper bearing
cone.
30. Remove the bearing cups from the sprocket housing.
(Type 1) Disassembly Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
11/19(W)
w
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...