This document is a service manual for several forage harvester models: FR450, FR500, FR600, FR700, and FR850. It contains technical information organized by system, including the engine, transmission, hydraulic systems, electrical systems, attachments, and other components. The manual provides specifications, descriptions of operation, diagnostic procedures, and service instructions.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
8. INTRODUCTION
Basic instructions - How to use and navigate through this Manual
Technical information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through Web delivery (eTim), DVD and in paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to
the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to describe
e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model for which the piece of technical information is written.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customer's concern on his
machine.
That information could be:
• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
47812460 09/01/2015
3
9. INTRODUCTION
How to use this manual
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:
• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components and assemblies.
• Service Data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents and assemblies.
Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a
number 00, 35, 55, etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.
PRODUCT
Tractors
Vehicles with working arms: backhoes,
excavators, skid steers, ….
Combines, forage harvesters, balers, ….
Seeding, planting, floating, spraying
equipment, ….
SECTION Mounted equipment and tools, ….
00 - Maintenance
05 - Machine completion and equipment
10 - Engine
14 - Main gearbox and drive
18 - Clutch
21 - Transmission
23 - Four wheel drive system
25 - Front axle system
27 - Rear axle system
29 - Hydrostatic drive
31 - Implement power take-off
33 - Brakes and controls
35 - Hydraulic systems
36 - Pneumatic system
37 - Hitches, drawbars and implement couplings
39 - Frames and ballasting
41 - Steering
44 - Wheels
46 - Steering clutches
48 - Tracks and track suspension
50 - Cab climate control
55 - Electrical systems
56 - Grape harvester shaking
58 - Attachments/headers
60 - Product feeding
61 - Metering system
62 - Pressing - Bale formation
47812460 09/01/2015
4
10. INTRODUCTION
63 - Chemical applicators
64 - Chopping
66 - Threshing
68 - Tying/Wrapping/Twisting
69 - Bale wagons
70 - Ejection
71 - Lubrication system
72 - Separation
73 - Residue handling
74 - Cleaning
75 - Soil preparation/Finishing
76 - Secondary cleaning / Destemmer
77 - Seeding
78 - Spraying
79 - Planting
80 - Crop storage / Unloading
82 - Front loader and bucket
83 - Telescopic single arm
84 - Booms, dippers and buckets
86 - Dozer blade and arm
88 - Accessories
89 - Tools
90 - Platform, cab, bodywork and decals
47812460 09/01/2015
5
11. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47812460 09/01/2015
12
12. INTRODUCTION
Safety rules - Ecology and the environment
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
• Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
• The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. NEW
HOLLAND strongly recommends that you return all used batteries to a NEW HOLLAND
dealer, who will dispose of the used batteries or recycle the used batteries properly. In
some countries, this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
• Accept the return of your used batteries
• Store the returned batteries in a suitable location
• Send the returned batteries to the battery manufacturer for recycling
47812460 09/01/2015
13
14. Engine - Engine and crankcase
Engine - Remove
FR450 WE
FR500 WE
DANGER
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply will result in death or serious injury.
D0076A
WARNING
Fall hazard!
Use a sturdy platform when working above ground level.
Failure to comply could result in death or serious injury.
W0926A
WARNING
Jack stands can slip or fall over. Dropping, tipping, or slipping of machine or its components is pos-
sible.
DO NOT work under a vehicle supported by jack stands only. Park machine on a level surface. Block
wheels. Support machine with safety stands.
Failure to comply could result in death or serious injury.
W0069A
NOTE: The assistance of a second person is required to perform the below operation.
1. Raise the spout to an appropriate height.
2. Remove the left-hand and right-hand side shielding.
Refer to Side shields - Remove side shieldings
(90.105).
3. Remove the rear shielding (3) as explained below:
A. Support the rear shielding (3). Use a suitable lifting
device.
B. Disconnect the gas strut (4) from the rear shielding
(3).
C. Remove the plate (6).
D. Remove the hardware (7).
E. Remove the rear shielding (3).
ZEIL11FR0029A0B 1
4. On both sides, remove the indicated plate.
ZEIL12FR0204A0Z 2
47812460 09/01/2015
10.1 [10.001] / 3
15. Engine - Engine and crankcase
5. For better access to the components, remove the steer-
ing wheels. Refer to Rear wheel - Remove – Steering
wheels (44.520).
6. In the service area, loosen the lock nut (13) and the nut
(12) until the worm (14) is completely free of the worm
wheel (15).
7. Manually move the spout to its extreme left or right
position.
ZEIL07FR0417A0Z 3
8. On the right-hand side under the machine, remove the
indicated plug. Drain the fuel from the fuel tank. Collect
the fuel in a clean container.
ZEIL13FR00346AB 4
NOTICE: The following operations require the removal
of the hydraulic hoses, tubes and other hydraulic compo-
nents. Once the hoses, tubes or the ports of the hydraulic
components are removed, cover with protective covers to
avoid the ingress of duct, contamination and other objects.
9. Drain the oil from the reservoir through the hose (16).
Refer to the Operator's Manual Oil filter - Replace
(29.204).
NOTICE: Pay attention to cleanliness, as the hydraulic
oil will be reused. Cover the oil container to prevent any
ingress of contamination.
ZEIL09FR0228A0Z 5
47812460 09/01/2015
10.1 [10.001] / 4
16. Engine - Engine and crankcase
10. Near the coolant tank, disconnect the connectors.
Disconnect the coolant level sensor wire (105) at-
tached at the top.
ZEIL13FR00307AB 6
11. Drain the coolant from the cooling system. Refer to
the Operator's Manual Engine cooling system - Re-
place (10.400).
12. Disconnect the hose (20), (21) and (22) from the
coolant tank (19).
13. Remove the coolant tank (19).
ZEIL11FR0031A0B 7
14. Remove the hardware (29). Loosen the clamp (30).
15. Remove the exhaust tube (23) from the muffler (24).
ZEIL13FR00306AZ 8
16. On the left-hand side, remove the hardware (1). Re-
move the sensor bracket (2).
ZEIL13FR00305AB 9
47812460 09/01/2015
10.1 [10.001] / 5
17. Engine - Engine and crankcase
17. On the right-hand side, remove the wire harness (25)
attached at the top and at the rear frame.
ZEIL11FR0033B0Z 10
18. On the left-hand side, remove the wire harness (27)
attached at the top and the rear frame.
ZEIL11FR0034B0Z 11
47812460 09/01/2015
10.1 [10.001] / 6
18. Engine - Engine and crankcase
19. On both sides at the rear of the engine roof assembly
(104), remove the hardware (103).
ZEIL13FR00308AB 12
ZEIL13FR00309AB 13
20. On the left-hand side of the engine roof assembly
(104), remove the hardware (103).
ZEIL13FR00310AB 14
21. On the right-hand side of the engine roof assembly
(104), remove the hardware (103).
ZEIL13FR00311AB 15
47812460 09/01/2015
10.1 [10.001] / 7
19. Engine - Engine and crankcase
22. From the engine roof assembly, remove the hardware
(70). Remove the plate (125).
ZEIL13FR00101AZ 16
23. On the left-hand side of the radiator fan plastic cover
(102), remove the hardware (103) from the engine roof
assembly (104).
ZEIL13FR00312AZ 17
24. On both sides, install the eye bolts (E) on the engine
roof assembly (104) as shown.
25. Connect the chain (C) of a suitable lifting device to the
eyebolts and the engine roof assembly (104).
26. Lift and remove gradually the engine roof assembly
(104) from the machine.
ZEIL13FR00313AB 18
NOTICE: Prevent the rotating coupler from damage during
any repair activity.
27. On the left-hand side, remove the rotating coupler
(33).
NOTICE: Use a metallic blank plug to prevent oil leakage.
Take care of the oil seal in the rotating coupler (33).
28. Remove the main drive belt (31). Refer to Drum gear-
box Belt drive - Remove - Main drive belt (64.130).
ZEIL09FR0323A0Z 19
47812460 09/01/2015
10.1 [10.001] / 8
20. Engine - Engine and crankcase
If "cutterhead reverse drive" is installed, perform steps 29 and 30
29. On the left-hand side, remove the hose (34) from the
tube (61).
30. Remove the reverse drive belt (32). Refer to Drum
gearbox Belt drive - Remove - Reverse drive belt.
(64.130).
ZEIL11FR0051A0B 20
31. On the left-hand side, remove the air intake ducts (35)
and (36).
ZEIL11FR0038A0B 21
32. On the right-hand side, loosen the clamps (9). Loosen
the last clamp (not indicated) on the intercooler tube
(8). Disconnect the intercooler tube (8).
ZEIL13FR00096AA 22
33. On the right-hand side, loosen the clamps (5). Dis-
connect the water tube (7).
ZEIL13FR00094AA 23
47812460 09/01/2015
10.1 [10.001] / 9
21. Engine - Engine and crankcase
34. On the right-hand side near the water tube (37), re-
move the hardware (38). Remove all the clamps.
35. Remove the intercooler tube (8) and the water tube
(7). Refer to figures 22 and 23.
ZEIL13FR00314AB 24
36. On the left-hand side, disconnect the hose (60) from
the water tube (59). Remove the water tube (59).
ZEIL11FR0050A0Z 25
37. On the left-hand side, remove the intercooler tube
(44).
ZEIL11FR0049A0Z 26
38. On the left-hand side, disconnect the tube (40) from
the muffler (24).
ZEIL13FR00315AZ 27
47812460 09/01/2015
10.1 [10.001] / 10
22. Engine - Engine and crankcase
39. On the right-hand side, loosen the clamp (41) near the
turbocharger end. Disconnect and remove the tube
(40).
ZEIL13FR00316AB 28
40. In the service area, remove the cover plate (120) to
have access to the batteries.
ZEIL12FR0203A0Z 29
41. Disconnect all the terminals (42) from the batteries
(43).
ZEIL13FR00317AB 30
42. On the left-hand side, disconnect the connector (71)
and (72) from the alternator (73).
ZEIL11FR0058A0B 31
47812460 09/01/2015
10.1 [10.001] / 11
23. Engine - Engine and crankcase
43. On the right-hand side, disconnect the air-condition-
ing hose (48) and (49) from the air-conditioning pump
(50).
ZEIL13FR00318AB 32
44. On the left-hand side, disconnect the Engine Control
Unit (ECU) connector (51) from the ECU (52). Discon-
nect the ECU fuel tube (56).
ZEIL13FR00319AB 33
45. On the left-hand side, disconnect the tube (108) from
the engine.
ZEIL13FR00320AB 34
46. On the right-hand side, disconnect the connector (17),
and other connectors from the feed rolls hydrostatic
pump (in case of single drive).
NOTE: If installed, do the same for the attachment hydro-
static pump (in case of double drive).
ZEIL13FR00324AZ 35
47812460 09/01/2015
10.1 [10.001] / 12
24. Engine - Engine and crankcase
47. From the oil reservoir (18), disconnect the hose (62),
(63) and (64).
ZEIL13FR00325AB 36
48. On the right-hand side, disconnect the connector
(115). Remove the wire harness (113). Disconnect
the tube (80) from the lubrication oil cooler.
ZEIL13FR00326AZ 37
49. On the right-hand side, disconnect the hose (82) and
(83) from the oil filter (84).
ZEIL11FR0062A0B 38
50. Above the main gearbox, disconnect the main gear-
box lubrication valve hose (78) and (79) from the tube
(80) and (81).
ZEIL11FR0061A0B 39
47812460 09/01/2015
10.1 [10.001] / 13
25. Engine - Engine and crankcase
51. On the left-hand side, disconnect the tube (81) from
the suction filter (118).
ZEIL13FR00078AF 40
52. Remove the fan drive belt. Refer to Belt - Remove
(10.414).
53. Swing the idler arm upwards and retain the idler arm
in the upward position. Use a strap.
ZEIL09FR0253A0B 41
If required, perform steps 54, 55, 56 and 57.
54. On both sides, loosen the hardware (66) from the ra-
diator fan frame (65).
ZEIL13FR00327AB 42
55. Attach a suitable lifting device to the pulley (67) of the
radiator fan.
56. Carefully remove the hardware from the radiator fan
frame (65). Remove the radiator fan assembly.
ZEIL13FR00328AB 43
47812460 09/01/2015
10.1 [10.001] / 14
26. Engine - Engine and crankcase
57. Behind the radiator, remove the support (68).
ZEIL13FR00329AB 44
58. On the rear of the engine, disconnect and remove the
hose (10) from the drain tap.
ZEIL13FR00323AZ 45
59. On the right-hand side, disconnect the hose (53) from
the filter assembly (54).
ZEIL13FR00321AZ 46
60. On the rear of the machine, disconnect the hose (55)
from the filter assembly (54).
61. Remove the bolts (107). Remove the filter assembly
(54) from the oil reservoir.
ZEIL13FR00322AB 47
47812460 09/01/2015
10.1 [10.001] / 15
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Engine - Engine and crankcase
62. On the main gearbox assembly, disconnect the hose
(69) from the gear pump (steering). Disconnect and
remove the hose (63) and (62).
ZEIL13FR00330AB 48
63. On the main gearbox, disconnect the hose (74). Dis-
connect and remove the hose (75).
ZEIL13FR00331AB 49
64. On the right-hand side, disconnect the hose (77) from
the fitting (76).
ZEIL13FR00332AB 50
65. On the right-hand side, remove the hose (64), (111)
and (112).
66. On the right-hand side, remove the supports (110) and
(109).
ZEIL13FR00333AB 51
47812460 09/01/2015
10.1 [10.001] / 16
29. Engine - Engine and crankcase
67. On the right-hand side, disconnect the hose (85) from
the tube (86). Disconnect the hose (87) from the tube
(88).
ZEIL13FR00334AB 52
68. On the main gearbox, disconnect the tube (89) from
the gear pump (main gearbox lubrication) (90). Dis-
connect the tube (116) from the tube (117).
ZEIL13FR00335AB 53
69. On the left-hand side, disconnect the hose (91), (92)
and (93) from the filter (94).
ZEIL13FR00336AZ 54
70. Disconnect the hose (95) and (96) from the Closed
Center Load Sensing (CCLS) pump on the main gear-
box.
NOTE: The view shown is from the top side of the main
gearbox.
ZEIL13FR00337AZ 55
47812460 09/01/2015
10.1 [10.001] / 17
30. Engine - Engine and crankcase
71. Loosen the hardware (97) from the muffler (24). Re-
move the muffler from the engine frame. Use a suit-
able lifting device.
ZEIL13FR00338AZ 56
72. At the rear, remove the tube (58) from the oil reservoir
(18).
ZEIL11FR0048A0B 57
73. On both sides, on the rear of the machine, remove the
hardware (98) from the engine support.
ZEIL13FR00339AB 58
74. On the right-hand side, remove the hardware (99).
ZEIL13FR00340AB 59
47812460 09/01/2015
10.1 [10.001] / 18
31. Engine - Engine and crankcase
75. On the left-hand side, remove all the hardware (100).
Remove the hardware (100) from the inner side also.
ZEIL13FR00341AZ 60
76. Attach the hooks (H) of a suitable lifting device on the
indicated areas of the engine and the main gearbox.
ZEIL13FR00342AB 61
77. Tilt the rear frame (101).
ZEIL13FR00344AB 62
NOTICE: Make sure that there are no connections between
the engine assembly and the frame of the machine.
78. From the left-hand side, carefully remove the engine
and the main gearbox assembly out of the machine as
shown.
ZEIL13FR00343AB 63
47812460 09/01/2015
10.1 [10.001] / 19
32. Engine - Engine and crankcase
79. Place the engine and the main gearbox assembly on
the wooden blocks (W).
ZEIL13FR00345AB 64
80. Remove the hardware (121) from the engine flange.
Separate the main gearbox assembly from the engine.
NOTICE: Main gearbox assembly is heavy. Use a suitable
lifting device.
ZEIL09FR0271A0Z 65
47812460 09/01/2015
10.1 [10.001] / 20