This document provides instructions for removing and installing the cylinder head on a Caterpillar 950B wheel loader with a 3304 engine. The removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods. The cylinder head bolts are then removed and a lifting device is used to remove the cylinder head weighing approximately 95 kg. The installation procedure details cleaning and preparing surfaces, installing gaskets and bolts in the proper sequence and torqueing them correctly.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w000...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 130G motor grader with a 3304 engine. It describes removing components like the fuel injection lines, exhaust manifold, rocker shaft and pushrods. It then details removing the cylinder head bolts and lifting the head off. Reinstallation involves cleaning surfaces, installing gaskets and bolts, and adjusting valves. Precautions are given to keep parts clean and contain fluids.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 936 f wheel loader (prefix 9mk) service repair manual (9mk000...fujskekfmsme
This document provides instructions for disassembling and assembling axle shaft assemblies for a 936F wheel loader. It describes removing the front and rear axle housing groups, and then removing individual components of the axle shaft assemblies including the axle shaft, planetary carrier assembly, retaining rings, seals, and bearings. Detailed steps are provided for disassembling the planetary carrier assembly. The document also includes instructions for assembling the components, including pressing in the ring gear and installing seals, bearings, and the adjusting nut. Tolerances and specifications are provided for installing components and adjusting the bearing nut torque.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w000...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 130G motor grader with a 3304 engine. It describes removing components like the fuel injection lines, exhaust manifold, rocker shaft and pushrods. It then details removing the cylinder head bolts and lifting the head off. Reinstallation involves cleaning surfaces, installing gaskets and bolts, and adjusting valves. Precautions are given to keep parts clean and contain fluids.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 936 f wheel loader (prefix 9mk) service repair manual (9mk000...fujskekfmsme
This document provides instructions for disassembling and assembling axle shaft assemblies for a 936F wheel loader. It describes removing the front and rear axle housing groups, and then removing individual components of the axle shaft assemblies including the axle shaft, planetary carrier assembly, retaining rings, seals, and bearings. Detailed steps are provided for disassembling the planetary carrier assembly. The document also includes instructions for assembling the components, including pressing in the ring gear and installing seals, bearings, and the adjusting nut. Tolerances and specifications are provided for installing components and adjusting the bearing nut torque.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v020...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304B or 3306B engine.
2. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and installing the camshaft ensuring proper alignment of timing marks.
3. Lubrication and cleaning of parts is emphasized to prevent contamination and wear during reassembly.
Caterpillar cat 966 f wheel loader (prefix 8bg) service repair manual (8bg000...fjjskkemsmee
This document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the torque converter by removing components like housing bolts, gears, bearings, seals and shafts. It then describes 26 steps for reassembling the torque converter by reversing the disassembly steps and ensuring proper alignment of components. Tools required include link brackets, drivers and pliers.
Caterpillar cat 323 f l excavator (prefix xcf) service repair manual (xcf0000...fusjejkdkmse
This document provides instructions for removing and installing crankshaft main bearings on a Caterpillar C7.1 engine. The procedure involves removing the main bearing caps and shells one pair at a time, keeping each cap and shell together. Thrust washers must be removed from number six main bearing using a crankshaft turning tool. New shells are cleaned and lubricated before installation. Main bearing caps are torqued to specification and end play is checked after installation is complete. A separate section provides instructions for removing the entire crankshaft, which requires first removing other engine components like the oil pump, front housing, rear seal, cylinder head, pistons and connecting rods.
Caterpillar cat 966 d wheel loader (prefix 35s) service repair manual (35s020...fjjskkemsmee
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. The instructions are:
1. Remove the starting motor and install a turning tool in the flywheel housing. Turn the flywheel to set the #1 piston at top center.
2. Remove plugs to view the #1 piston through an inspection hole and install a bolt when the piston is at top center.
3. Install the fuel injection pump housing and governor, ensuring proper timing between components.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying engine oil to bolts before tightening to specified torques.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsjjekdkme
The document provides instructions for installing a cylinder head on a 120G motor grader with a 3304 engine. It involves 16 steps: cleaning and preparing surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and installing related components like intake pipes and hoses. The instructions emphasize keeping parts clean to prevent wear and include illustrations to clarify steps.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 120 h motor grader (prefix 5fm) service repair manual (5fm000...fusefjjskekemm
- The document provides instructions for removing and installing the camshaft on a 120H Motor Grader with a 3116 engine. It describes removing components like the governor and covers, then turning the crankshaft to align marks before removing the camshaft, gear, and bearings. Installation is the reverse of removal.
- Instructions are given to remove and install the camshaft gear by pressing it off the camshaft and heating it to 315°C before reinstalling.
- The procedure to remove and install camshaft bearings uses a special tool and orients the oil holes during installation.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w000...fjjsekkdmme
This document provides instructions for removing and installing the cylinder head on a 130G motor grader with a 3304 engine. It describes removing components like the fuel injection lines, exhaust manifold, rocker shaft and pushrods. It then details removing the cylinder head bolts and lifting the head off. Reinstallation involves cleaning surfaces, installing gaskets and bolts, and adjusting valves. Precautions are given to keep parts clean and contain fluids.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjjsekkdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...dkdmidkkdk
This document provides instructions for removing and installing various engine components on a Caterpillar 3304 engine, including:
- Removing and installing the cylinder head, which involves removing fuel lines, exhaust manifolds, rocker shafts, and bolts holding the head to the block.
- Removing and installing the spacer plate beneath the cylinder head, which requires replacing gaskets and seals.
- Removing and installing water directors in the cylinder head, cleaning parts thoroughly.
The document provides detailed step-by-step instructions and illustrations for each procedure. Safety notices are included to handle fluids properly and avoid contaminating parts.
This document provides instructions for removing and installing the cylinder head on Caterpillar 330 and 330L excavators. The key steps are:
1. Remove components attached to the cylinder head like the fuel injection lines, exhaust manifold, and rocker shaft/pushrods.
2. Remove bolts securing the cylinder head to the cylinder block and lift off the cylinder head using a lifting device.
3. Clean surfaces and install a new gasket before reinstalling the cylinder head. Tighten bolts in a specific sequence to the correct torque specifications.
4. Reinstall any removed components like the intake manifold, rocker shaft, and connect hoses.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fikkskkdmmd
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...f9oseikkdks
This document provides instructions for removing and installing the cylinder head on a 3304 engine. The key steps are:
1. Remove components like the fuel lines, exhaust manifold, and rocker shaft before removing the cylinder head.
2. Remove all bolts securing the cylinder head, then lift it off using a lifting device due to its weight of approximately 95 kg.
3. To install the cylinder head, position a new gasket and the cylinder head on the engine. Install bolts and tighten them in a specific sequence to the correct torques.
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Caterpillar cat 966 f wheel loader (prefix 8bg) service repair manual (8bg000...fjjskkemsmee
This document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the torque converter by removing components like housing bolts, gears, bearings, seals and shafts. It then describes 26 steps for reassembling the torque converter by reversing the disassembly steps and ensuring proper alignment of components. Tools required include link brackets, drivers and pliers.
Caterpillar cat 323 f l excavator (prefix xcf) service repair manual (xcf0000...fusjejkdkmse
This document provides instructions for removing and installing crankshaft main bearings on a Caterpillar C7.1 engine. The procedure involves removing the main bearing caps and shells one pair at a time, keeping each cap and shell together. Thrust washers must be removed from number six main bearing using a crankshaft turning tool. New shells are cleaned and lubricated before installation. Main bearing caps are torqued to specification and end play is checked after installation is complete. A separate section provides instructions for removing the entire crankshaft, which requires first removing other engine components like the oil pump, front housing, rear seal, cylinder head, pistons and connecting rods.
Caterpillar cat 966 d wheel loader (prefix 35s) service repair manual (35s020...fjjskkemsmee
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. The instructions are:
1. Remove the starting motor and install a turning tool in the flywheel housing. Turn the flywheel to set the #1 piston at top center.
2. Remove plugs to view the #1 piston through an inspection hole and install a bolt when the piston is at top center.
3. Install the fuel injection pump housing and governor, ensuring proper timing between components.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying engine oil to bolts before tightening to specified torques.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsjjekdkme
The document provides instructions for installing a cylinder head on a 120G motor grader with a 3304 engine. It involves 16 steps: cleaning and preparing surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and installing related components like intake pipes and hoses. The instructions emphasize keeping parts clean to prevent wear and include illustrations to clarify steps.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 120 h motor grader (prefix 5fm) service repair manual (5fm000...fusefjjskekemm
- The document provides instructions for removing and installing the camshaft on a 120H Motor Grader with a 3116 engine. It describes removing components like the governor and covers, then turning the crankshaft to align marks before removing the camshaft, gear, and bearings. Installation is the reverse of removal.
- Instructions are given to remove and install the camshaft gear by pressing it off the camshaft and heating it to 315°C before reinstalling.
- The procedure to remove and install camshaft bearings uses a special tool and orients the oil holes during installation.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w000...fjjsekkdmme
This document provides instructions for removing and installing the cylinder head on a 130G motor grader with a 3304 engine. It describes removing components like the fuel injection lines, exhaust manifold, rocker shaft and pushrods. It then details removing the cylinder head bolts and lifting the head off. Reinstallation involves cleaning surfaces, installing gaskets and bolts, and adjusting valves. Precautions are given to keep parts clean and contain fluids.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjjsekkdmme
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...dkdmidkkdk
This document provides instructions for removing and installing various engine components on a Caterpillar 3304 engine, including:
- Removing and installing the cylinder head, which involves removing fuel lines, exhaust manifolds, rocker shafts, and bolts holding the head to the block.
- Removing and installing the spacer plate beneath the cylinder head, which requires replacing gaskets and seals.
- Removing and installing water directors in the cylinder head, cleaning parts thoroughly.
The document provides detailed step-by-step instructions and illustrations for each procedure. Safety notices are included to handle fluids properly and avoid contaminating parts.
This document provides instructions for removing and installing the cylinder head on Caterpillar 330 and 330L excavators. The key steps are:
1. Remove components attached to the cylinder head like the fuel injection lines, exhaust manifold, and rocker shaft/pushrods.
2. Remove bolts securing the cylinder head to the cylinder block and lift off the cylinder head using a lifting device.
3. Clean surfaces and install a new gasket before reinstalling the cylinder head. Tighten bolts in a specific sequence to the correct torque specifications.
4. Reinstall any removed components like the intake manifold, rocker shaft, and connect hoses.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fikkskkdmmd
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...f9oseikkdks
This document provides instructions for removing and installing the cylinder head on a 3304 engine. The key steps are:
1. Remove components like the fuel lines, exhaust manifold, and rocker shaft before removing the cylinder head.
2. Remove all bolts securing the cylinder head, then lift it off using a lifting device due to its weight of approximately 95 kg.
3. To install the cylinder head, position a new gasket and the cylinder head on the engine. Install bolts and tighten them in a specific sequence to the correct torques.
Similar to Caterpillar cat 950 b wheel loader (prefix 63r) service repair manual (63r00001 06053) (11)
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualfjsjjekdkme
This document is the shop manual for a hydraulic excavator. It contains outlines, precautions, and general information for repairing and maintaining the excavator. The manual is divided into chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for safety, preparing for disassembly, hydraulic and electrical equipment, and welding repairs. Copyright information is also included.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety practices, hydraulic system repair, electrical work, and welding. Permission is required to copy or distribute content from the copyrighted manual. Measurements use the international unit system. Technicians should thoroughly read and understand the manual before performing any repair work.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Kobelco sk60 8 hydraulic excavator service repair manualfjsjjekdkme
This document appears to be a shop manual that contains information for maintenance and repair of hydraulic excavators. It includes sections on specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures. The document provides safety precautions for repairs and disassembly/assembly. It also includes a table for international unit conversion. The manual is intended as a technical reference for maintenance technicians to perform repairs and find fault equipment.
This shop manual provides information needed for the disassembly, reassembly, and repair of a Kawasaki 135ZV-2 wheel loader. It includes specifications, tightening torques, and service standards for the chassis, power, hydraulic, brake, and operator station systems. Safety precautions and symbols are defined. The manual instructs technicians on removing and installing major components like the engine, transmission, axles, cylinders, and more. Cautions are provided regarding parts handling and use of sealants or lock agents.
This shop manual provides information for performing maintenance and repairs on Kawasaki wheel loaders. It contains safety warnings and symbols, an outline of the loader components and maintenance schedule, recommended lubricants, and sections about inspecting and adjusting the chassis and power groups. Technical details are given for linkage pins, center pins, engine and transmission mounts, and the radiator mount. The purpose is to ensure good machine performance through following the correct maintenance and repair procedures.
Kawasaki 92 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 92 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component information for operating heavy machinery. It outlines proper procedures for starting and using the machine, transporting loads, and performing maintenance safely. Operators must follow guidelines to prevent injuries or accidents from improper or unsafe operation. The manual describes the various controls, switches, and components in the operator cab.
Kawasaki 90 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and reassembling a wheel loader. It discusses preparing the work area, inspecting components, draining fluids, cleaning parts, applying lubricants, and ensuring proper tightening of fasteners. Special attention should be given to sliding surfaces, seals, and markings for reassembly. Tools and loose parts should be accounted for after completion. Floating seals and nylon slings require special handling to prevent damage or improper installation.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)fjsjjekdkme
This document provides specifications and component layout information for a 90Z6 wheel loader.
The specifications section lists operating weights, engine details, dimensions, speeds and other technical specifications for the GSC and LSC models.
The component layout sections include diagrams and lists showing the layout and weights of major components such as the chassis, powertrain, hydraulic, electrical and other systems. Component names, locations and approximate weights are provided.
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document is a parts catalog for a wheel loader model 90Z6 powered by a Cummins QSM11 engine. It lists parts grouped by system including the front axle, rear axle, power train, engine systems, cab, chassis, electrical systems, hydraulic system, brake system and loader attachments. The document provides part numbers, part names, quantities and the applicable serial number range for each part listed.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)fjsjjekdkme
This document provides specifications and layout diagrams for the components of a wheel loader. It includes:
- Specifications for dimensions, weights, engine details, speeds, and more.
- Overview diagrams showing the layout of main components such as the bucket, cylinders, lights, engine, and more.
- Detailed diagrams labeling locations of the engine, radiator, filters, tanks, valves, pumps, axles, and other parts.
- An overview of the electric system components around the cab, hydraulic oil tank, fuel tank, and engine.
- Sections providing specifications for the engine, hydraulic and electrical components.
The document contains detailed information on the specifications, component layout and electrical
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00991114
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
C. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00505124
1. Loosen hose clamp (2) on the hose that connects the oil cooler to water pump elbow (1) .
Illustration 2 g00505164
2. Remove two bolts (3) that fasten water pump elbow (1) to the cylinder head. Remove two
bolts (4) that fasten water pump elbow (1) to the water pump.
3. Carefully remove water pump elbow (1) and the gaskets from the engine.
2/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00538842
4. Disconnect tube (5) from the inlet manifold.
Illustration 4 g00538845
5. Remove four bolts (6) and remove air inlet pipe (7) .
Illustration 5 g00541454
3/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. NOTICE
Do not set the cylinder head on a hard, flat surface. Damage may occur
to the fuel injection nozzle tips.
6. Remove all bolts (8) and (9) that hold the cylinder head to the cylinder block.
Illustration 6 g00505311
7. Attach the proper lifting device in order to remove cylinder head (10) from the engine.
Remove cylinder head (10) from the engine. The weight of cylinder head (10) is
approximately 95 kg (210 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 8 19:48:13 UTC+0800 2020
4/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07489822
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
Illustration 1 g00541495
1/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
Illustration 2 g00541497
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
Illustration 3 g00511493
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 4 g00602759
3304B torque sequence
10. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 18) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 18) again in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 18) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through E) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
3/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 5 g00328807
3306B torque sequence
11. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 26) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through G) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
12. Adjust the inlet valve lash to 0.38 mm (.015 inch) and the exhaust valve lash to 0.64 mm
(.025 inch). Tighten the locknuts for the adjusting screws to a torque of 29 ± 7 N·m
(22 ± 5 lb ft). Refer to the Testing and Adjusting, "Air Inlet and Exhaust System" topic for
additional information on valve lash adjustments.
Illustration 6 g00511911
13. Put the gasket and air inlet pipe (7) in position on the cylinder head. Install four bolts (6) to
fasten air inlet pipe (7) to the cylinder head.
Illustration 7 g00541522
4/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 14. Connect tube (8) to the inlet manifold.
Illustration 8 g00541524
15. Put the gaskets and water pump elbow (11) in position on the engine. Install two bolts (9)
that fasten water pump elbow (11) to the cylinder head. Install two bolts (10) that fasten
water pump elbow (11) to the water pump.
Illustration 9 g00541527
16. Tighten hose clamp (12).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
c. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 8 19:49:09 UTC+0800 2020
5/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01045029
Spacer Plate - Remove and Install
SMCS - 1221-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00540847
1/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 1. Remove O-ring seal (1), water seals (3) and water directors (4) from spacer plate (2) .
Illustration 2 g00540857
NOTICE
Do not damage the dowels as the spacer plate is removed.
2. Remove spacer plate (2) from the cylinder head.
Illustration 3 g00540895
3. Remove O-ring seal (6) and spacer plate gasket (5) from the cylinder head.
Installation Procedure
2/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the mating surfaces between the spacer plate and the cylinder block.
Illustration 4 g00540895
2. Install new spacer plate gasket (5) and new O-ring seal (6) .
Note: If the dowels in the cylinder block have been removed for any reason, the overall
height of the installation is 16.0 ± 5.0 mm (.63 ± .20 inch).
Illustration 5 g00540857
Note: Both surfaces of the spacer plate, spacer plate gasket and the top of the cylinder block
must be clean and dry. Do not use any gasket adhesive or other substances on these
surfaces.
3/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 3. Install spacer plate (2) on the cylinder head.
Illustration 6 g00540847
4. Install a new O-ring seal (1). Install new water seals (3). Install new water directors (4) .
5. Check the cylinder liner projection. Refer to Disassembly and Assembly, "Cylinder Liner -
Install".
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 8 19:50:06 UTC+0800 2020
4/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00943364
Water Directors - Remove and Install
SMCS - 1115-010
Removal Procedure
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00481082
1/2
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 1. Remove water directors (1) from the cylinder head.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the cylinder head before assembly.
Illustration 2 g00481082
2. Install new water director (1) into the cylinder head. Align the notch in water director (1)
with the "V" mark on the cylinder head.
3. Install water director (1) to a depth of 0.8 ± 0.6 mm (0.031 ± 0.023 inch) below the surface
of the cylinder head.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 8 19:51:03 UTC+0800 2020
2/2
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01042782
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 1 g00538891
1. Use Tool (A) to remove valve lifter (1), as shown. Put identification marks on the valve
lifters for installation purposes.
2. Repeat Step 1 for the remainder of the valve lifters.
3. Check the diameter of the valve lifters. The diameter of a new valve lifter must be 33.285 ±
0.015 mm (1.3105 ± 0.0005 inch). The diameter of the bore in the cylinder block for a new
valve lifter must be 33.388 ± 0.050 mm (1.3145 ± 0.0020 inch). The maximum permissible
clearance between the valve lifter and the valve lifter bore in the cylinder block must be
0.30 mm (0.012 inch).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Illustration 2 g00538891
2/3
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. 1. Put 8T-2998 Lubricant on valve lifter (1) prior to installation. Install valve lifter (1) with
Tool (A) in the original location in the cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 8 19:51:59 UTC+0800 2020
3/3
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01037991
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
B. Remove the timing gear cover. Refer to Disassembly and Assembly, "Front Housing -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g00476744
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. The "C" mark on
the crankshaft gear will be aligned with the "C" mark on the camshaft gear.
Illustration 2 g00476743
Note: Put a mark on the teeth of the fuel injection pump drive gear and the idler gear at
location (A). This will help to keep the engine timing correct during the removal and the
installation of the camshaft. Put a mark on the teeth of the idler gear and camshaft gear (2)
at location (B). When the camshaft is installed, the engine timing will be correct when the
mark at location (A) is aligned with the mark at location (B) and the "C" mark on the
crankshaft gear is aligned with the "C" mark on the camshaft gear.
2. Remove the bolts, the lock and washer (1) .
Illustration 3 g00535590
2/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. NOTICE
Do not damage the lobes or the bearings when the camshaft is
removed.
3. Carefully remove camshaft (3) from the engine.
4. If necessary, remove the bolts that hold camshaft drive gear (2) to the camshaft and remove
the gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00535590
1. Put camshaft drive gear (2) in position on the end of camshaft (3). Install the bolts that hold
camshaft drive gear (2) to camshaft (3). Tighten the bolts to a torque of 55 ± 7 N·m (41 ± 5
lb ft).
NOTICE
Do not damage the lobes or the bearings when the camshaft is installed.
3/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. 2. Put 8T-2998 Camshaft Lubricant on the camshaft lobes only and put clean engine oil on the
bearing journals.
Note: During the installation of camshaft (3), rotate the camshaft in both directions in order
to prevent binding in the camshaft bearing bores.
3. Carefully install camshaft (3) into the engine.
Illustration 5 g00476743
Illustration 6 g00476744
4. Make sure that the mark on the teeth of the fuel injection pump drive gear and the idler gear
are in alignment at location (A). Make sure that the mark on the teeth of the idler gear and
camshaft gear (2) are in alignment at location (B). Align the "C" marks on the crankshaft
gear and camshaft gear (2). When all of the timing marks are in alignment the engine timing
is correct.
4/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 5. Install washer (1), the lock and the two bolts that hold the camshaft in position in the
engine.
End By:
a. Install the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Install the timing gear cover. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 8 19:52:56 UTC+0800 2020
5/5
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 950B WHEEL LOADER 63R
Configuration: 950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02473351
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the Flywheel Housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
B. Remove the Oil Pan Plate. Refer to Disassembly and Assembly, "Oil Pan Plate - Remove
and Install".
C. Remove the Camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 1 g00478567
1. Use Tool (A) to remove the camshaft bearing from the cylinder block. Start with the front
bearings and work to the rear bearing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
950B WHEEL LOADER 63R00001-06053 (MACHINE) POWERED BY 3304 ENGI...
2020/4/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...