The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and removing the camshaft retainer plate and camshaft. Reinstallation involves cleaning parts, installing the camshaft and ensuring proper timing marks are aligned, and replacing the retainer plate and covers.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
The Future of Autonomous Vehicles | civilthings.com | Detailed informationgettygaming1
civilthings.com Present Autonomous vehicles, also known as self-driving cars, represent a groundbreaking advancement in transportation technology. These vehicles utilize sophisticated sensors, advanced software, and machine learning algorithms to navigate roads and transport passengers without human intervention. Major companies in the autonomous vehicle industry are investing heavily in the development and testing of these innovative machines, aiming to enhance safety, efficiency, and convenience on the roads.
The autonomous vehicle market is rapidly expanding, driven by technological progress and increasing consumer interest. With the advent of autonomous vehicle technology, the future of transportation promises significant changes, including reduced traffic accidents and lower emissions. However, the widespread adoption of autonomous vehicles faces challenges, such as regulatory hurdles, safety concerns, and public acceptance.
Autonomous vehicle regulations and legislation are evolving to address these issues, ensuring that the integration of self-driving cars into everyday life is smooth and secure. As the industry grows, news and trends related to autonomous vehicles continue to capture global attention. From the development of cutting-edge sensors to advancements in autonomous vehicle software, this sector is poised to revolutionize how we think about mobility.
Stay informed about the latest in autonomous vehicle technology, industry developments, and market trends to understand the profound impact these vehicles will have on our future.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01196838
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the
idler gear and the crankshaft gear.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
3. Wire the valve lifters away from the camshaft.
Illustration 1 g00640035
4. Remove two bolts (3) and camshaft retainer plate (2) from camshaft gear (1).
Illustration 2 g00640030
5. Remove camshaft (4) from the cylinder block.
2/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01196611
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00640030
1. Carefully install camshaft (4) in the engine.
NOTICE
1/2
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the
idler gear and the crankshaft gear.
Illustration 2 g00640035
3. Install camshaft retainer plate (2) and two bolts (3) on camshaft gear (1).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:11:54 UTC+0800 2020
2/2
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983227
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00987675
NOTICE
1/2
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Place camshaft (2) and camshaft gear (1) in a suitable press. Press camshaft (2) from
camshaft gear (1).
3. If necessary, remove the key (3) from the camshaft.
Installation Procedure
Illustration 2 g00987675
1. Raise the temperature of camshaft gear (1).
2. Align key (3) in the camshaft with the groove (keyway) in the camshaft gear.
3. Install camshaft gear (1) on the end of camshaft (2).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:12:50 UTC+0800 2020
2/2
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02183087
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
1. Use Tooling (A) to remove the camshaft bearings from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01104577
3/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01104579
1. Use Tooling (A) to install all of the camshaft bearings except for the front bearing. Orient
oil hole (1) in each bearing so that oil hole (1) is located at the top of the bore.
2. Use Tooling (A) to install the front camshaft bearing. Align oil hole (1) in the front
camshaft bearing with the oil hole in the cylinder block. Locate joint (2) in the front
camshaft bearing in the proper position.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:13:46 UTC+0800 2020
4/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02173704
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/5
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g00610543
Typical example
Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to
tap lightly on the engine oil pan, if it is necessary.
2. Remove the bolts for engine oil pan (1). Remove engine oil pan (1) .
Illustration 2 g00610550
Typical example
2/5
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 3. Remove gasket (2) from engine oil pan (1) .
4. Remove the drain plug and the O-ring seal from engine oil pan (1) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9612 Silicone Sealant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install the drain plug and the O-ring seal on the engine oil pan. Tighten the drain plug to 25
± 5 N·m (18 ± 4 lb ft).
2. Inspect the condition of the gasket. Replace the gasket, if necessary.
Note: On newer engines, the oil pan has an integral seal. Inspect the condition of the seal
and replace the seal, if necessary.
Illustration 3 g01010643
3/5
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Clean the mating surface of the engine oil pan and the cylinder block.
4. Apply Tooling (A) to the T-shaped gasket joints of the oil pan. Refer to Illustration 3.
Illustration 4 g00610550
Typical example
Illustration 5 g00610543
Typical example
5. Position new gasket (2) and engine oil pan (1) on the cylinder block.
4/5
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g00610574
6. Install the bolts for the engine oil pan. Tighten Bolts (X) to a torque of 31 ± 3 N·m (23 ± 2
lb ft).
7. Start at Bolt (Z) and tighten the remaining bolts in a counterclockwise direction. Tighten the
remaining bolts to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
8. Start at Bolt (Z) and tighten the bolts again in a counterclockwise direction. Tighten the
bolts to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
9. Fill the engine with oil to the correct level. Refer to the Operation and Maintenance Manual
for the correct filling procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:14:42 UTC+0800 2020
5/5
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02372739
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00987444
1. Remove bolt (2) and piston cooling jet (1) from each cylinder.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g00987444
1. Position piston cooling jet (1) in the cylinder block. Install bolt (2). Tighten the bolt to a
torque of 28 ± 7 N·m (21 ± 5 lb ft).
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:15:37 UTC+0800 2020
3/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02180392
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
b. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
c. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
The joint between the connecting rod and the connecting rod cap is
produced by fracturing. The connecting rod assembly must be handled
with care in order to avoid damage to the mating surfaces. The
connecting rod assembly must be replaced if any damage occurs to the
mating surfaces. New connecting rod assemblies come with the
connecting rod caps bolted on the connecting rod.
1/2
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Use only a soft jawed vise to hold the connecting rod assembly when
removing the connecting rod cap bolts. Use only a soft faced hammer
to tap the connecting rod cap when separating the connecting rod cap
from the connecting rod.
Failure to use a soft jawed vise and a soft faced hammer may result in
damage to the connecting rod assembly.
1. Turn the crankshaft until the connecting rod caps are at the bottom center.
Illustration 1 g01062853
2. Inspect connecting rod (1) and connecting rod cap (3) for the proper identification mark.
The connecting rod and the connecting rod cap should have an etched number on the side
that is toward the right side of the engine. The number should match the cylinder number.
Mark the connecting rod and the connecting rod cap, if necessary. Do not etch new
markings on connecting rod or rod cap.
3. Remove connecting rod bolts (2) and connecting rod cap (3).
4. Remove the lower half of connecting rod bearing (5) from connecting rod cap (3).
5. Push the piston and the connecting rod away from the crankshaft. Remove the upper half of
connecting rod bearing (4) from connecting rod (1).
6. Remove the piston and connecting rod (1) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:16:33 UTC+0800 2020
2/2
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983492
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00988677
1. Use Tooling (B) to remove retaining ring (2). Remove piston pin (4) and separate piston (1)
from connecting rod (3).
2/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g00988681
2. Use Tooling (A) to remove piston rings (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:17:29 UTC+0800 2020
3/3
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR CRB
Configuration: 325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983502
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Verify correct assembly of the pistons and the connecting rods. Ensure
that the etched numbers on the rod and the rod cap are in the correct
positions. The etched number on the rod and the rod cap correspond to
the cylinder in which it should be installed.
1/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00988681
1. Check the clearance between the ends of piston rings (5). Refer to the Specifications
Manual, "Pistons and Rings".
Note: The oil ring must be installed over the spring with the end gap 180 degrees from the
oil ring spring joint.
2. Install the oil control piston ring with Tooling (A). The ends of the spring should be rotated
180 degrees from the ring end gap.
3. Install the intermediate piston ring with the side marked "UP-2" toward the top of the
piston. Use Tooling (A) in order to install the intermediate piston ring.
4. Install the top piston ring with the side marked "UP-1" toward the top of the piston. Use
Tooling (A) in order to install the top piston ring.
2/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 2 g00988732
5. Replace rod bearing (6) by pressing a new bearing into the connecting rod. Refer to Special
Instruction, SEHS7295 for the correct tooling and the correct installation procedure.
Illustration 3 g01027812
3/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 6. The piston is a two-piece assembly. This piston consists of piston crown (7) and piston skirt
(8). Bearing (9) is nonserviceable.
Illustration 4 g00988677
NOTICE
An improperly installed retainer ring could cause the piston and
connecting rod to come apart during engine operation. This action can
result in a broken Piston Skirt and major engine damage.
7. Position piston (1) on connecting rod (3). Coat pin (4) with clean engine oil and install pin
(4). Ensure that the retainer rings are in the grooves of piston (1).
End By:
a. Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 13 23:18:25 UTC+0800 2020
4/4
325C L & 325C LN Excavator CRB00001-UP (MACHINE) POWERED BY 3126 En...
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...