2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120M 2 MOTOR GRADER R9W
Configuration: 120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
120M Series 2 Motor Grader Power Train
Media Number -KENR9467-02 Publication Date -01/05/2017 Date Updated -16/05/2017
i06013976
Rear Axle, Differential and Final Drive - Disassemble
SMCS - 3258-015; 3278-015; 3282-015-RE; 4050-015; 4068-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 4
B 140-7742 Sleeve 2
C 386-6031 Lever Puller Hoist 1
D 154-6182 Forcing Bolt 3
E 439-3939 Link Bracket 2
F
8B-7551 Bearing Puller Gp 1
1P-5546 Crossarm 1
3H-0465 Push-Puller Plate 2
5F-7366 Forcing Screw 1
G 292-4949 Socket Wrench As 1
H 154-6183 Forcing Bolt 3
J 1U-6405 Three Jaw Puller 1
Start By:
A. Remove the rear axle.
1/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals. Replace the O-ring seals that are worn or damaged.
Illustration 1 g01413868
1. Use Tooling (A) , Tooling (B) , and two suitable lifting devices in order to position rear axle
(1) onto suitable blocking. The weight of rear axle (1) is approximately 1089 kg (2400 lb).
Illustration 2 g01418559
2/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Remove bolts (3) , retainer (4) , shims (5) , sprocket (2) , and sprocket (6) .
Note: Note the quantity and the order of shims (5) .
Illustration 3 g01414357
3. Remove bearing cone (7) .
Illustration 4 g01412778
3/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 4. Attach Tooling (A) , Tooling (C) , and two suitable lifting devices onto final drive housing
(8) . The weight of final drive housing (8) is approximately 191 kg (420 lb). Remove nuts
(9) and bolts (9A) .
5. Use Tooling (D) in order to remove final drive housing (8) .
Illustration 5 g01419912
6. Remove bolts (10) . Remove retainer (11) .
Illustration 6 g01352280
7. Remove shims (12) . Use Tooling (A) and a suitable lifting device in order to remove
housing (13) . The weight of housing (13) is approximately 54 kg (120 lb).
Note: Note the quantity and the order of shims (12) .
4/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g01352292
8. Remove thrust washer (14) . Remove wear sleeves (15) .
Illustration 8 g01352299
9. Turn over housing (13) . Remove lip seal (16) .
Illustration 9 g01414353
10. Remove bearing cup (17) . Remove thrust washer (18) .
5/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01352320
11. Remove lip seal (19) . Remove bearing cup (20) .
Illustration 11 g01419983
12. Use Tooling (E) in order to remove carrier assembly (21) and drive shaft (22) . The weight
of carrier assembly (21) and drive shaft (22) is approximately 136 kg (300 lb).
6/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01419985
13. Use Tooling (F) in order to remove bearing cone (23) .
Illustration 13 g01352339
14. Remove retaining ring (24) in order to remove axle shaft (22) from carrier assembly (21) .
Illustration 14 g01352406
15. Remove bolts (25) and retainer (26) . Remove pin (27) . Remove gear (28) . Remove thrust
washers (29) and bearings (30) . Repeat this step for the remaining planetary gears.
7/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01352384
16. Remove axle shaft assembly (31) .
Illustration 16 g01352402
17. Remove retaining ring (32) in order to remove gear (33) from axle shaft (34) .
Illustration 17 g01352438
18. Use Tooling (D) in order to separate ring gear (35) from the intermediate housing.
8/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01352445
19. Use Tooling (B) and a suitable lifting device in order to remove ring gear (35) . The weight
of ring gear (35) is approximately 25 kg (55 lb).
20. Repeat Step 2 through Step 19 for the opposite side.
Illustration 19 g01353587
21. Position differential housing (36) with intermediate housing (37) upward.
9/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g01419994
22. Attach a suitable lifting device onto pinion (38) . Use Tooling (H) in order to separate
pinion (38) from the center housing. Remove bolts (39) in order to remove pinion (38) . The
weight of pinion (38) is approximately 56 kg (123 lb).
Illustration 21 g01353021
23. Remove shims (40) . Remove O-ring seal (41) .
Note: Note the order and the quantity of shims (40) .
10/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g01353002
24. Remove bolt (42) . Remove retainer (43) . Remove yoke (44) . Remove guard (45) .
Illustration 23 g01353512
25. Remove shims (46) . Remove lip seal (47) .
Note: Note the order and the quantity of shims (46) .
Illustration 24 g01353570
26. Remove pinion (48) . Remove bearing cone (49) . Remove bearing cup (50) . Remove
bearing cone (51) . Remove bearing cup (52) .
27. Use Tooling (G) in order to remove nut assembly (54) .
11/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 25 g03772865
28. Remove bolts (53) . Remove bolts (54) .
Illustration 26 g01419996
Typical Example
29. Use Tooling (J) in order to separate intermediate housing (37) from differential housing
(36) .
12/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 27 g01420124
Typical Example
30. Use Tooling (E) in order to remove intermediate housing (37) . The weight of intermediate
housing (37) is approximately 32 kg (71 lb).
Illustration 28 g03772901
Typical Example
31. Before installing Tooling (A) remove the shims. Use Tooling (A) in order to remove
bearing assembly (55) and differential (56) . The weight of bearing assembly (55) and
differential (56) is approximately 102 kg (225 lb).
13/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 29 g03772885
32. Remove bolts (57) . Remove shroud (58) .
Illustration 30 g03772948
33. Remove bolts (59) . Use Tooling (G) and remove lock-nut (60) .
Illustration 31 g03772966
34. Use Tooling (F) in order to remove bearing assembly (55) .
14/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 32 g01354900
35. Remove bearing cone (63) . Remove bearing cups (64) .
Illustration 33 g01420000
36. Use Tooling (J) in order to remove spacer (65) and bearing cone (66) .
Note: This step is a destructive procedure. Replace bearing cone (66) .
15/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 34 g01353751
37. Remove retaining ring (67) . Remove bearing race (68) . Remove O-ring seals (69) .
Remove thrust ring (70) .
Illustration 35 g01353760
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
38. Remove bolts (71) . Remove case (72) .
16/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 36 g01353766
39. Remove thrust washer (73) . Remove plates (74) and discs (75) . Remove springs (76) .
Note: Note the quantity and the order of plates (74) and discs (75) .
Illustration 37 g01353940
40. Remove housing (77) .
Illustration 38 g01353944
41. Remove differential gear (78) .
17/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 39 g01353945
42. Remove spider assembly (79) .
Illustration 40 g01353954
43. Remove thrust washer (80) , pinion gear (81) , and bearing sleeve (82) from spider (83) .
Repeat this step for the remaining pinion gears (81) .
Illustration 41 g01353965
18/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 44. Remove differential gear (84) . Remove thrust washer (85) .
Illustration 42 g01353970
45. Use two people in order to turn over housing (86) and bevel gear (87) . The combined
weight of housing (86) and bevel gear (87) is approximately 59 kg (130 lb). Remove bolts
(88) . Use two people in order to remove housing (86) from bevel gear (87) . The weight of
housing (86) is approximately 41 kg (90 lb). The weight of bevel gear (87) is approximately
19 kg (41 lb).
Illustration 43 g01355203
46. Remove bearing assembly (89) . Remove piston (90) .
19/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 44 g01355208
47. Remove thrust race (91) , thrust bearing (92) , and thrust race (93) from piston (90) .
Illustration 45 g01355211
48. Remove seals (94) from piston (90) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 11 10:46:00 UTC+0800 2020
20/20120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POW...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 120M 2 MOTOR GRADER R9W
Configuration: 120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
120M Series 2 Motor Grader Power Train
Media Number -KENR9467-02 Publication Date -01/05/2017 Date Updated -16/05/2017
i07285127
Rear Axle, Differential and Final Drive - Assemble
SMCS - 3258-016; 3278-016; 3282-016-RE; 4050-016; 4068-016
Assembly Procedure
Table 1
Required Tools
Tool
Part
Number
Part Description Qty
A 439-3940 Link Bracket 4
B 140-7742 Sleeve 2
C 386-6031 Lever Puller Hoist 1
E 143-3939 Link Bracket 2
G 292-4949 Socket Wrench As 1
H 154-6183 Forcing Bolt 2
K 4C-4030 Thread Lock Compound 1
L 1U-8846 Gasket Sealant 1
M
6V-2012 Depth Micrometer 1
367-9109 Caliper(1)
1
N
8T-5096 Dial Indicator Gp 1
301-3405 Gauge 1
P 8T-4140 Bolt 4
R 7M-7456 Bearing Mount Compound 1
1/27120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. S - Cat Advance 3Moly Grease or Dow Corning Molykote BR2 -
Plus
1
T 8T-5096 Dial Indicator Gp 1
(1)
For use with three bolt retainers
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Inspect the O-ring seals, gaskets, and lip seals. Replace O-ring seals, gaskets, and lip seals
that are worn or damaged.
Note: Lubricate O-ring seals and lip seals with the lubricant that is being sealed.
Illustration 1 g03831520
1. Install seals (94) onto piston (90).
Illustration 2 g03831488
2/27120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Note: Grease is used to hold thrust race (93) and thrust bearing (92) in place during
assembly.
2. Apply a liberal amount of grease to thrust race (93) and to thrust bearing (92). Install thrust
race (93) and thrust bearing (92) onto piston (90).
Illustration 3 g01355203
3. Install piston (90). Lower the temperature of bearing assembly (89). Install bearing
assembly (89).
Illustration 4 g01353970
4. Use two people to install housing (86) onto bevel gear (87). The weight of housing (86) is
approximately 41 kg (90 lb). Install bolts (88). Tighten bolts (88) to a torque of
300 ± 40 N·m (221 ± 30 lb ft).
5. Use two people to turn over bevel gear (87) and housing (86). The combined weight of
bevel gear (87) and housing (86) is approximately 59 kg (130 lb).
3/27120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 5 g01353965
6. Install thrust washer (85). Install differential gear (84).
Note: Install thrust washer (85) with the groove side against gear (84).
Illustration 6 g01353954
7. Install bearing sleeve (82), pinion gear (81), and thrust washer (80) onto spider (83). Repeat
this step for the remaining pinion gears (81).
Illustration 7 g01353945
8. Install spider assembly (79).
4/27120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 8 g01353944
9. Install differential gear (78).
Illustration 9 g01353940
10. Install housing (77).
Note: Ensure that the notches on the housings are aligned.
Illustration 10 g01353766
5/27120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 11. Install plates (74) and discs (75). Install thrust washer (73). Install springs (76).
Note: Lubricate the discs with the lubricant that is being sealed.
Note: Install thrust washer (73) with the groove side against the gear.
Illustration 11 g01353760
Typical Example
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Determine bolt size before torquing bolts (71).
12. Install case (72). Install bolts (71). Tighten M16 bolts (71) to a torque of 300 ± 40 N·m
(220 ± 30 lb ft). Tighten M12 bolts (71) to a torque of 120 ± 20 N·m (90 ± 15 ft)
6/27120M Series 2 Motor Grader - All Wheel Drive R9W00001-UP (MACHINE) POWER...
2020/5/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...