Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions       ...
Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions       ...
Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions       ...
Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions       ...
Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions       ...
Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions       ...
Upcoming SlideShare
Loading in …5
×

Chapeu instruçoes

1,360 views

Published on

Instruções de montagem do chapéu com a vassoura

Published in: Education, Spiritual, Technology
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
1,360
On SlideShare
0
From Embeds
0
Number of Embeds
833
Actions
Shares
0
Downloads
5
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Chapeu instruçoes

  1. 1. Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions © Takako Takahashi Before starting assembly:Writing the number of each section on its back side before cutting out the sections is highly recommended. Indicates where sections (* This way, you can be sure which section is which even after cutting should be glued together. out the sections.) http://www.canon.com/c-park/en/ 1 View of completed model Assembly Instructions: Six A4 sheets (No.1 to No.6)*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order. B *Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold. Assembly Instructions 1-7 Glue A Mountain fold(dotted line) The glue spot(colored dot) Make a mountain fold. shows where to apply the glue. Valley fold(dashed and dotted line) 1-6 Glue spot(Red dot) Make a valley fold. Glue parts with the same number together. 1-5 Scissors line(solid line) Glue spot(Green dot) Cut along the line. Glue within the same part. Cut in line(solid line) Glue spot(Blue dot) A Cut along the line. Glue to the rear of the other part. 1-4 1-1 1-2 Scissors, set square, glue(We recommend stick glue), pencil, used Tools and materials ballpoint pen, toothpicks, tweezers, (useful for handling small parts) 1-3 B Before gluing, crease the paper along mountain fold and valley Assembly tip fold lines and make sure rounded sections are nice and stiff. Glue, scissors and other tools may be dangerous to young children Caution so be sure to keep them out of the reach of young children. 1
  2. 2. Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions © Takako Takahashi Glue parts 2-4, 2-5, and 2-6 from above. Glue parts 2-1, 2-2, and 2-3 to the inside of part 1. After gluing the shaded area 2 on the cross-section diagram, cut along lines in parts 2-1, 2-2, and 2-3. 1 2
  3. 3. Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions © Takako Takahashi 3-2 Glue to the inside 3-1 at whatever angle you prefer. 1+2 3-3 3-4 3 3 3
  4. 4. Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions © Takako Takahashi 4-1 4-2 Glue any design you prefer to any position on the hat. 4-3 The hat is finished! 4
  5. 5. Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions © Takako Takahashi 5-4 5-3 5-2 5-1 Glue to the inside, Glue to the inside, Glue to the inside, matching the wood grain. matching the wood grain. matching the wood grain. 6-1 5 2 6-1 1 After gluing point 1, roll tightly and glue point 2. 6-1 6-2 2 1 6-2 After gluing point 1, roll tightly and glue point 2. Use a round pencil or other cylindrical object to curve this piece. 5
  6. 6. Canon ® is a registered trademark of Canon Inc. © Canon Inc.Witchs hat and broom (Halloween): Assembly Instructions © Takako Takahashi 6-3 5-5 6-3 Glue to the inside. 2 1 After gluing point 1, roll tightly and glue point 2. Use a round pencil or other cylindrical object to curve this piece. 5 6-4 6-4 Use any string you like to hang part 7 (the black cat), 2 part 8 (the bat), 1 and part 9 (the snake). After gluing point 1, roll tightly and glue point 2. Use a round pencil or other cylindrical object to curve this piece. 97-1 8-2 7-4 7-2 7-3 8-1 6

×