Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Process journal

301 views

Published on

dt process journal

Published in: Business, Education
  • Be the first to comment

Process journal

  1. 1. Process JournalDate: 21 September 2011Title:Drawing and Measuring Body Of The Moving ToyWhat You Did:Today I use a pencil to draw the rabbit’s shape on the wood. I use a tri-square tomark lines across the other end. This tells me where do I draw my rabbit at theother side. I finished drawing my rabbit’s head and body.Emotions:I was really excited to start making my moving toy. Sometimes I really can’t waittill we enter in the create section.AOI learning profile:Today, I learn that we need to draw our moving toy on both sides of the wood. Ialso learn that if we draw to small, the small little parts will break easily.Why?The reason I need to draw my rabbit on the other end is because we will knowwhere to cut on both sides.Pictures and Diagrams:Drawing my rabbit on the hard wood.
  2. 2. Using tri-square to mark out lines.Changes to my plan:So far I didn’t make any changes to my plan.What’s next?The next thing that I will do is using a coping saw to cut out the shape of therabbit’s body. I need to cut out the shape of the rabbit’s leg. I think I will finish allof this plans.
  3. 3. Date: 25 September 2011Title:Using a coping sawEmotion:I was really happy that I learn more skills when I am cutting softwood. I feelnervous when I think that I am doing the wrong thing.What I did:Today, I use a coping saw to cut out the shape of my moving toy’s body. I turnedmy moving toy when I am cutting at the lowest part. Other then cutting mymoving toy’s body, I also cut the head of the moving toy.Why:I turn my moving toy around when I am cutting the body part. The reason Iturned around is because I’m not cutting the table but I am cutting my movingtoy. The reason that I am using a coping saw instead of a tenon saw is because Iam cutting curved shapes.AOI learning profile:Today, I learn that I should lower down the position of my timber. The reason Ido this is because I will break the coping saw’s blade if it is too high. The secondreason is because it will be easier to cut the moving toy.Pictures and diagramUsing a coping saw to cut the shape of a rabbit’s head.
  4. 4. Changes to my plans:So far, I didn’t make any changes to my plans.What’s next?I need to finish cutting my timber by the next lesson. I need to cut the legs for mymoving toy. The last thing I will do is to draw a cool skateboard on a new timber.I will finish all this things in the next lesson.
  5. 5. Date: 26 September 2011Title:Learning more skills to use a coping sawWhat I did:For today, I continue using a coping saw to cut the rabbit’s body. I broke thecoping saw twice when I was cutting. I realized that the way I was using acoping saw wasn’t correct. After that, I changed the way that I used it. I don’tknow why the coping saw broke at the second time when I was using thecorrect way. I didn’t pull the coping saw out of the timber when I want tochange the angle of cutting it.Why:The reason that we are not supposed to pull the saw out of the timber isbecause the blade is very tin.Emotions:I was very nervous when I broke the saw. I feel very stressful when I brokethe 2nd blade. The reason I feel very stressful is because I didn’t pull thecoping saw out of the timber and the blade broke.AOI learning profile:Today, I learn a lot of skills. The first skill that I learn was learning how to pullthe coping saw out of the timber correctly.Pictures and diagram:Using a coping saw to cut the rabbit’s body. Coping saw are use to cut curveshapes.
  6. 6. Changes to my plans:So far I didn’t make any changes to my plans.Plans:I will finish cutting the rabbit’s body and I will need to sand all the edges andmake it smooth. I also need to cut out the rabbit’s leg and finally theskateboard.
  7. 7. Date: 28 September 2011Title:Using Disc sander to cut the rough edge off.What I Did:Today I used the flat-headed tool to file all the corners off. I also used Discsander to cut off all the rough edges. Before using that machine, I checked allmy safety rules. I wore safety goggles and I started my work. I used garnetpaper to rub the both surfaces. I rubbed it in 1 direction.Why?The reason I use the garnet paper to rub only in 1 direction is because I willrub all the fibers.AOI Learning Profile:I should use the garnet paper to rub the where the lines are pointing.Emotions:Today was a very interesting day learning design technology. I startedlearning more skills in using tools and machines.Pictures And Diagrams:Filing the corners using flat file toolChanges To Plans:So far, I didn’t make any changes to my plans.What’s next?
  8. 8. Start drawing my skateboard on a new timber. I’m going to use a tenon saw tocut my skateboard out.
  9. 9. Date: 8 October 2011Title:Using a tenon saw to cut the bottom part of the rabbit’s bodyWhat I did:Today, I use a tenon saw to cut the bottom part of the rabbit’s body. I useddisc sander to sand the bottom part off, this will make it the bottom partstraight. After sanding my rabbit’s body, I drew a shape of a skateboard on anew timber.Why:The reason I use a tenon saw instead of other saws is because I am cutting astraight line. If I am cutting curves shapes, I will use coping saw to cut it.Emotion:I feel very proud of myself, because I did a lot of things today.AOI learning profile:Today, I learn that I should draw my skateboard on the side of the timber. Ifwe draw anything in the middle of the timber, we will waste a lot of wood.Pictures And Diagram:Draw skateboard on a new timber
  10. 10. Using a tenon saw to cut the bottom part of the rabbit’s body.Changes to my plans:So far, I didn’t make any changes to my plans.What’s next?The next thing that I should do is to cut my skateboard and fix all the problems.I need to start making wheels for my skateboard in the next lesson.
  11. 11. Date:10 October 2011Title:Using a coping saw to cut my skateboard shapeWhat I did:Today, I used a coping saw to cut my skateboard. I used the coping saw tocut the curves and a tenon saw to cut straight line. After finishing cutting it, Iuse a disc sander to sand my skateboard. I sand all the rough edges on theside. I also used garnet paper to run the surface on the skateboard.Why:The reason I check safety rules before using disc sander is because, it’simportant or it will be dangerous.Safety rules:• Wear safety goggles• Nothing else is around there• Wear apronsAOI Learning Profile:I learn that I should draw my skateboard on the side or else I will waste a lotof wood. We must not waste wood and we should use it properly.Emotions:Today it was a really cool day when I did a lot of things in today’s lesson. Ihope that I will do more fun things in the next lesson.Pictures and Diagrams:Using a coping saw to cut my skateboard shape
  12. 12. Using disc sander to sand the sides off and to make them smoothUsing garnet paper to sand the surface off.Changes to my plans:So far, I didn’t make any changes to my plans.What’s next?I need to use trimmer router to cut the sharp sides off on my skateboard andmy rabbit. After this, I need to create wheels for my skateboard.
  13. 13. Date:12 October 2011Title:Using trimmer router to cut my skateboard and my rabbit’sedge offWhat I did:Today, I check all the safety rules and waited for instruction before I used thetrimmer router.After everything is ready, I hold the trimmer router and cut theedge off. I cut the rabbit and the skateboard’s edge off.Why:Safety rules:•Wear safety goggles•Never on the trimmer router unless the teacher ask you to•Apron on•Got to wait for the trimmer router’s blade to stop spinning before laying itdownAOI Learning Profile:In today’s lesson, I learn that when I am using the trimmer router, we shouldcut it in anti clockwise direction.Emotions:Today’s lesson was a bit boring, because I waited too long using the trimmerrouter.Pictures And Diagrams:Using trimmer router to cut the skateboard’s edge offChanges to my plans:I didn’t make any changes to my plans.
  14. 14. What’s next?I need to create 4 wheels for my skateboard in today’s lesson. If there isenough time, I need combine my wheels and skateboard together.Changes to my plans:So far, I didn’t make and changes to my plans.What’s next?I need to start making wheels using a machine. I need to draw markings onmy skateboard and start drilling my wheels into the skateboard.
  15. 15. Date:16 October 2011Title:Drawing 4 wheels on a timberWhat I Did:Today, I used a pencil to draw 4 wheels on a new timber. I used a timber thatpeople had used to create wheels to draw my wheels. I chose timbers thathave big wheels on it, because I need big wheels on a skateboard. I drew allmy wheels at the same size.Why:The reason I drew all the wheels at the same size is because I want themovement of the skateboard to be smooth.Emotions:Today, there wasn’t enough time to complete my plans in 1 period. I feel verysad and frustrating whenever I can’t complete anything. I feel like rushing andfinishing all the plans I have in today’s lesson.Pictures and diagrams:Using tenon saw to cut the timber for the wheels.
  16. 16. Using a pencil to draw wheels.Changes to my plans:So far, I didn’t make any changes to my plans.What’s next?I need to make wheels using the machine. I also need to drill my wheels intothe skateboard.Date:17 October 2011Title:Using pedestrian drill to make wheelsWhat I did:Today, I used the pedestrian drill to make wheels. I wore safety goggles and Iclamped my timber tightly to the table. I on the green button to start and I pulldown the thing slowly. When it is drill halfway, I turn the timber around andstart making the other side. I repeat these steps 3 times to make 4 wheels.After making all the wheels, I used garnet paper to sand the wheels.Why:
  17. 17. The reason I ask a teacher to watch me when I am using the pedestal drill isbecause this is my first time using it. This is a more safety way to use themachine. I used garnet paper to sand my wheels because the wheels can’troll if there are sharp edges around the wheels.AOI learning profile:Today was a very special day; I finally know how to use the pedestrian drillproperly. This was my first time using the pedestrian drill and I learnt a lot ofexperience when I am using it.Emotions:Today I used a very scary machine, which is the pedestrian drill. I feel verynervous when I am using because I’m scared that I will break the drill. It wasexciting when I learn something new, but I am very serious when I am using it.Pictures and diagrams:Using pedestal drill and wheel cutting bit make wheelsUsing garnet paper to sand my wheels.
  18. 18. Changes to my plans:So far, I didn’t make any changes to my plans.What’s next?The next thing that I should do is to sand my wheels using garnet paper. Ineed to draw markings on my skateboard and start drilling my wheels into myskateboard.Date:19 October 2011Title:Drill holes in my skateboard for my wheels using pedestal drillWhat I did:Today, I continue to sand my wheels using garnet paper. After sanding, I tookmy skateboard and drill 2 holes on the skateboard for my wheels. I usedpedestal drill-to-drill holes in my skateboard. I cut a stick using a tenon saw formy wheels.Why:Safety rules when you are using the pedestal drill• Wear safety goggles• Wear apron• Hold on the clamp when you are drilling
  19. 19. • Do not drill it too fast• Wait for teacher’s instruction before you turn onEmotions:Today I feel very comfortable when I am using the pedestal drill, because Ilearn a lot of tiny experience when I am using it the last time. It found that it isreally relaxing when I am using it. Nothing happen if I drill it slowly.Pictures and diagrams:Drill my holes in my skateboard using pedestal drillChanges to my plans:So far, I didn’t make any changes to my plans.What’s next?I need to continue cutting sticks for my wheels. I need to drill holes in mywheels using pedestal drill.
  20. 20. Date:26 October 2011Title:Drill holes in my wheels and the skateboard using pedestal drillWhat I did:Today, I use a tenon saw to cut the stick for my wheels. I used the pedestaldrill to drill holes in my wheels and my skateboard. I drill 2 holes in the middleof the skateboard and 1 hole in the middle in each wheel.Why:Safety rules while using pedestal drill: - Wear safety goggles - Wear apron - Wait for instructions - Drill it slowly
  21. 21. Emotions:Today, It was a good day to learn a lot of interesting stuff. I enjoy a lot when Iknow how to use the pedestal drill. I finish all my plans in time and I feel proudof myself.Pictures and diagrams:Drilling holes in the middle part of the skateboard using pedestal drillTimberChanges to my plans:So far I didn’t make any changes to my plans.What’s next?I need to draw markings and start drilling everything together. After this I needto start painting my moving toy.Date:30 October 2011Title:Cutting the stick shorter with a tenon sawWhat I did:Today, I cut the stick with a tenon saw to make it shorter. It’s too long for mywheels. I drill 4 holes in my skateboard so that it will be ready to screw 4screws in my skateboard after I paint it.Why:The reason that I should paint everything first before I joined everythingtogether is because some parts need to be painted before joining everythingtogether.Emotions:
  22. 22. Today, It was a great day to learn a lot of interesting stuff. I am glad that I amup to the painting stage. It is fun when I am painting beautiful colors on mymoving toy.Pictures and diagrams:Using tenon saw to cut the stick shorter.Drilling holes in my skateboardChanges to my plans:Today I decided that I should change 1 of my plans. Instead of painting mywheels brown, I need to paint it yellow. The reason for me painting it yellow isbecause there isn’t blue in the box.What’s Next?I need to continue painting my 4 wheels and I need to let it dry up. I need topaint my skateboard and after that I need to paint my rabbit.
  23. 23. Date:31 October 2011Title:Painting my wheels and skateboard with beautiful colorsWhat I did:Today, I grab a small brush, cardboard, painting pallet, paint, and seteverything up. I paint my wheels with yellow color. I let my wheels dry after Ifinished painting my wheels. I use the color black, to paint my skateboard.Why?The reason I should paint the edges first before painting the surfaces itbecause we should finish the hardest part first.Emotions:
  24. 24. Today, I’m glad that I’m up to the painting stage. I can’t wait to see how is mymoving toy.Pictures and diagrams:Painting my wheels yellowPainting my skateboard blackChanges to my plans:So far, I changed some of my plans. I painted my wheels yellow instead ofbrown. The reason I painted my wheels to yellow is because there isn’t brownin the box.What’s next?I need to sand my skateboard using garnet paper and continue painting itagain. I need to repeat this a lot of time. After that, I need to start painting myrabbit.
  25. 25. Date:6 November 2011Title:Sanding skateboard and paint it againWhat I did:Today, I sand all my parts using different kinds of garnet paper. I used 180 tosand my skateboard. I used 360 to make my skateboard smoother. After that,I grab paintbrush, pallet, and cardboard, paint. I set everything up and Istarted painting my skateboard black. I let my skateboard to dry and I usegarnet paper to sand my rabbit.Why:
  26. 26. The reason I painted the sides on the skateboard first it is because the sidesis the hardest part to paint. We should always complete the hardest part firstand then the easiest part.AOI learner profile:Today, I learnt to use different kinds of garnet paper to sand my skateboard. Ican use 180 first and then 360. This will make my skateboard smoother.Emotions:Today, It was a really relaxing day because I have a lot of fun when I ampainting my skateboard. I feel a bit bored when I heardthat I need to sand andpaint my skateboard 4 times.Pictures and diagrams:Sand my skateboard using garnet paperPainting my skateboard blackChanges to my plans:I didn’t make any changes to my plans.
  27. 27. What’s next?I need to sand my skateboard and paint my skateboard. I need to repeat thisprocess 3 times more. I also need to paint my rabbit with different beautifulcolors.
  28. 28. Date:7 November 2011Title:Sanding my skateboard with different grids of garnet paperWhat I did:Today, I used 180 to sand my skateboard. After that, I used 360 to sand myskateboard. This process actually works because I did tried touching myskateboard’s surface before I use 360. I painted black on the sides of myskateboard and the surfaces. I also sand my wheels using 180 and after that Ipainted my wheels using yellow paint.Why?The reason repeats the sanding and painting process it’s because the movingtoy will be really smooth.Emotions:Today was a really great day because we have 2 periods and I manage tocomplete all my plans. I was glad that I just need to repeat the process 2 moretimes and I am done with my skateboard.Pictures and diagrams:Sand my skateboard using garnet paper
  29. 29. Painting my skateboard blackChanges to my plans:So far I didn’t make any changes to my plans.What’s next?The next thing that I need to do is to paint my rabbit. I need to let it dry andafter that I need to sand it again.Date:9 November 2011Title:Painting my rabbit whiteWhat I did?Today, I sand my skateboard using 360 grid garnet paper. After that I sandedmy wheels using 360 grid garnet paper. I paint my wheels and my skateboard.After that, I paint my rabbit using white paint. I paint the body of the rabbitwhite.Why?The reason I didn’t paint my rabbit’s ear white it’s because I am painting othercolors at the ears. The reason I paint before I drill 2 holes in my rabbit isbecause I need to set everything up before I drill and put the 2 eyes in myrabbit.Emotions:I was glad that I complete my plans today. Today was a great day becausewe have 2 periods of design technology to finish our plans. I feel a little bit ofbored when I am waiting for the paint to dry.
  30. 30. Pictures and diagrams:Painting my skateboard blackPainting my rabbit whiteChanges to my plans:Today, I painted my rabbit white instead of peach.What’s next?I need to paint my rabbit using white on the other side and I need to sand it. Ineed to repeat this process more than 4 times.
  31. 31. Date:13 November 2011Title:Sanding my rabbit using garnet paperWhat I did?Today I sand my rabbit and skateboard using smooth garnet paper. I paintedmy rabbit using white color on the sides. After that, I painted my rabbit usingwhite color on both sides. I sanded the sides of my rabbit after my rabbit is dry.Why:The reason I paint the sides of my rabbit first before I paint the surfaces it’sbecause we should always complete the hardest part first and then theeasiest part.Emotions:Today wasn’t a really lucky day because we only have1 period for designtechnology, but it was good that I completed all my plans.I feel a bit boredwhenever I repeat the sanding and painting process.Pictures and diagram:Using 180 grid garnet paper to sand my skateboard.
  32. 32. Using 306 grid garnet paper to sand my skateboard.Changes to my plans:I decided to drill 2 holes at the rabbit’s face after I have finish the sanding andpainting stage. I need to put 2 eyes on the rabbit’s face.What’s next?I need to sand my skateboard and rabbit using grid 180 and 360 garnet paper.After that, I need to paint all the parts again.
  33. 33. Date:14 November 2011Title:Sanding and paintingWhat I did?Today, I sand my wheels, skateboard rabbit using garnet paper. At first I used180 to sand all the parts and then 360. I painted my skateboard black on thesides. After that, I painted my skateboard on the 2 surfaces.Why?The reason I paint the sides first before painting the surfaces it’s because it iswe should paint the hardest part before painting the easiest part.AOI learner profile:I learn that we should paint the dark colors first before painting the light colors.Emotions:I was glad that I finished the sanding and painting process on my skateboard.It was a great day because we have 2 awesome periods to complete our work.If I’m not wrong, I will finish my project at the end of this week.Pictures and diagrams:Sanding my skateboard using 180 grit garnet paper.
  34. 34. Painting my skateboard black with a paintbrushChanges to my plans:I didn’t make any changes to my plans so far.What’s next?I need to sand and paint my rabbit white 3 more times and I need to repaintmy wheels. After that I need to screw in 2 holes at the rabbit’s face to put ineyes.
  35. 35. Date:16 November 2011Title:Sanding and paintingWhat I did?Today, I sand my rabbit using 360 grid garnet paper. After that I painted myrabbit white. I sand my wheels because it is too rough. I tear the garnet paperinto half and I sand it. I use garnet paper to sand my skateboard to make itsmoother.Why?The reason I wait for my rabbit to dry for 24 hours before sanding is becauseit is not fully dry.Emotions:I was glad that I finished the sanding and painting process on the skateboard.I feel a little bit of bored when I’m not finish sanding and painting my rabbit.Pictures and diagrams:Sanding my rabbit using 180 grid garnet paper
  36. 36. Change to my plans?I didn’t make any changes to my plans so far.What’s next?I need to paint my rabbit again on the sides and the surfaces. I need to drill 2holes in the face and screw the eyes in the rabbit.
  37. 37. Date:19 November 2011Title:Painting my rabbit whiteWhat I did?Today, I grab garnet paper and sand the sides of the rabbit. I also sand thesurfaces, because I want to repaint it. After that, I grab a cup of water,paintbrush, white paint, card box, and pallet. I started using all this stuff topaint my rabbit.Why?The reason I need to repaint my rabbit again Is because there is still a lot ofempty spaces in my rabbit. The second reason is I want to make it smoother.Emotions:Today it was a great day because I don’t need to sand and paint myskateboard any more. Today it was an interesting because I’m finished withpainting all my stuff.Pictures and diagrams:Changes to my plans:So far, I didn’t make any changes to my plans.What’s Next?I need to drill 2 holes at the rabbit’s face and glue the eyes together on therabbit’s face. I screw 4 screws in my skateboard.

×