Hagm 3021 !

758 views

Published on

Manual

Published in: Education, Business
0 Comments
1 Like
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total views
758
On SlideShare
0
From Embeds
0
Number of Embeds
6
Actions
Shares
0
Downloads
10
Comments
0
Likes
1
Embeds 0
No embeds

No notes for slide

Hagm 3021 !

  1. 1. OPERATOR’S MANUAL I. Installation Manual II. Operation Manual III. Maintenance Manual HYDRAULIC VARIABLE RAKE GUILLOTINE SHEAR HAGM 3021 Serial No: MVD INAN Takım Tezgahları Sanayi A.Ş. 1
  2. 2. IMPORTANT: This protocol must be returned back to MVD INAN, being signed within 1 weekafter commissioning of the machine. This is the document forming the basis for the startof guarantee period.Machine Type: HAGM 3021Series NumberDesign based on standard: prEN 13985:2001, CEI/IEC 60204-1997+A1:1999CustomerThe following checks must be carried out by the customer or a qualified service engineerbefore the machine is commissioned.1. Installation and levelling2. Oil level3. Electrical connections, correct voltage and fuses4. Hydraulic system5. Test Run6. Functional testThe undersigned declares that he /she has received the operator’s manual and CEdeclaration together with the machine. Furthermore, he/she shall ensure that the machineoperating personnel reads and understands all of the instructions with regard to the use ofthe machine and its safety related aspects and the procedures in this manual is strictlyadhered to.Remarks:Signature: Date:Customer: Agent or MVD INAN Service EngineerName: Name:Position: 2
  3. 3. Table of ContentsImportant iTable of contents iiAttention iiiIntroduction 1I. INSTALLATION MANUAL 2I.1 Lifting and carrying 2I.2 Foundation 2I.3 Levelling 2I.4 Filling the oil tank 4I.5 Electrical mains connection 4I.6 Starting up the machine 4II. OPERATION MANUAL 5II.1 PRODUCT INFORMATION 5II.1.1 General features 5II.1.2 Technical features 5II.1.3 Remarks 6II.2 SAFETY 6II.2.1 Instructions 6II.2.2 Safety equipments 7II.2.2.1 Control cabinet and electrical switchgear cabinet 7II.2.2.2 Fixed guards 7II.2.2.3 Light beams 7II.2.2.4 Safety switch and lock bar 7II.2.2.5 Foot pedal 8II.2.2.6 Adjustment of cut length 8II.2.2.7 Pressure relief valves 8II.2.2.8 Emergency stop button 8II.2.2.9 Reset button 8II.2.3 Liability 8II.3 OPERATION 8II.3.1 Modes of position switch 9II.3.2 Adjustment of cut length 9II.3.3 Back gauge adjustment 9II.3.4 To end the operation 12III. MAINTENANCE MANUAL 13III.1 Lubrication 13III.2 Mechanical system maintenance 13III.3 Hydraulic system maintenance 13APPENDIX A: Explanatory wordlist 16APPENDIX B: Hydraulic circuit and equipments 17APPENDIX C: Electrical circuit and equipments 22APPENDIX D: Operation manual for digital control unit 3
  4. 4. INTRODUCTION This operator’s manual is designed to give supportive and corrective instructions tothe operating and maintenance personnel concerning commissioning, operation andmaintenance of the machine. It is separated into 3 parts : I. Installation Manual, II.Operation Manual, III. Maintenance Manual.Unless it is permitted by written instruction of the manufacturer, any operation oradjustment, which is not in line with this operator’s manual, will be on customer’s own riskand manufacturer will have the right to end the guarantee period. If any further technical information is required, our service department will bepleased to provide you on request. For information or for spare parts and service please send your fax to: MVD INAN Service Department Konya / Turkiye Tel: +90.332.2392233 Fax: +90.332.2392121 service@mvdinan.com 4
  5. 5. MVD INAN HAGM I. INSTALLATION MANUALI.1 Lifting and carrying Machine, which is loaded and send safely, when received by customer, must beunpacked and checked to see if there is anything damaged or missing. Steel ropes mustbe used to hang the machine from the 4 lifting extensions on both columns of the machine(See figure-1). It is the customer’s responsibility to lift, carry and place the machine safelyand suitably regarding regulations. The machine must be well cleaned and the rust preventive coating on the metalsurfaces must be cleared of by appropriate chemicals, kerosene or petrol. It is suggestedto coat these surfaces with a thin layer of machine oil. See also Operation’s manualsection II.3.3.I.2 Foundation The foundation upon which the machine is to be installed should be concrete andmust be levelled and flat. Sufficient space should be left around the machine in order toallow inspection and maintenance operations in addition to safe handling of work piecesand cutting tools. During bending operations, the force exerted must be absorbed by the concretefoundation The foundation must also bear the machine weight and to keep the machinefixed during any earthquake shake. See Figure1 as reference.Attention: It is a must for customer to fix the machine by anchor bolts to the ground andalso to make the ground connection from the earth connection built into switchgearcabinet to the ground line of the factory.I.3 Levelling While placing the machine on the foundation prepared, 20 mm. thick iron plates mustbe supplied under each corner of the machine and the machine must be levelled bothlengthwise and crosswise. The levelling of the machine is maintained by the 4 bolts(1) infig. 1 on the foot of the machine and fixing is maintained by the nuts(3) on the studs(2) infig.1. A water level must be placed on the lower table and levelling must be made withinacceptable inclines as follows: Crosswise levelling : about 0.1 mm/m. (machine depth) Lengthwise levelling : about 0.2 mm/m. (machine length) Anchor bolts are not included as a part of machine and can be supplied at extraprice. 5
  6. 6. 3088 4092 2548 3471 11 ton. 1744 - c-... "hen machine will arrive. fix it with c:;) through pointed holes 513c:;)....., 2294 0 C1 M HAGM 3020 FIGUREMVDv LIFTING AND FOUNDATION OF MACHINE MAKIN A SANAVIA. 1-2
  7. 7. I.4 Filling the oil tank Fill the oil tank up to 3-4 cm. below the top cover of the tank, with one of the belowmentioned oil. The trouble free functioning of the hydraulic system is very muchdependant on the quality and condition (cleanliness and purity) of the hydraulic oil whichis used. The oil must possess the following minimum properties:Viscosity at 40 °C : 46 cStViscosity index : approx. 105Examples : Shell Tellus 46, BP Energol HLP 46, Esso Nuto H 46 , Aral oil 46, : Mobil DTE 25I.5 Electrical main supply connection The machine’s electrical connection is ready for use. Only the 3 phases of supplyvoltage has to be connected to the main switch on the cabinet. The earth connection mustbe made to the earth terminal. For the main supply, shielded cable must be used and theshield must be fixed to the metal gland at the entrance of the cabinet. Electrical connections are to be made by properly qualified personnel and inaccordance with the applicable standards. The cross-section of the connection cable mustsuit the total power required as mentioned on the machine plate. The rotation of motor is limited to one direction. When all electrical connections aremade, safety conditions are maintained and the start button is pressed, if the motor doesnot rotate, just interchange the main switch connections of two phases and it will rotate.See also section I.6.I.6 Starting up the machine The shop and machine main switches are turned on, emergency stop buttons arefreed and then the reset button is pressed. The power light on the machines electricalcabinet shall then come on. (If not, control the main supply circuit and light beams at therear). When start button is pressed, the motor will rotate. If the power light does not comeon, then there is some problem due to the safeguarding system established and themachine won’t work. In this case, the light beams and switch of safety bar underneathupper beam is checked to see it is closed. Then the safety “reset” button is pressed again.If there is still problem, MVD INAN or the Agent must be contacted.
  8. 8. ATTENTION• Do not operate the machine before reading the “operator’s manual”.• The machine must be fixed to the concrete floor as described in section I.2.• Before starting the machine, be sure the tank is full of oil.• Input voltage will be 380-400 volts and current will be 50 Hz.• The cable of mains supply will be 4 x 6 mm². R, S, T for the phases and GND for the ground (Earth) line of the building.• For the safe of the pump, the rotation of motor is limited to be in one direction only. So if the motor does not start, two of the phases (R, S, T) must be in interchanged from the connection of the main electricity switch on the cabinet.• The electricity cabinet shall be kept close when operating.• Operations such as welding, grinding must not be carried on or by the machine.• Do not make any readjustment on the set positions of the hydraulic valves.• The machine shall be operated only by the responsible who read and comply with operator’s manual.• Inform the agent or manufacturer for any problem occur.
  9. 9. MVD INAN HAGM II. OPERATION MANUALII.1 PRODUCT INFORMATIONII.1.1 General features 1. Swing beam type movement of the upper beam, 2. Rigid and robust structure due to completely welded steel construction of side housing, table and tank. 3. Most precise machining of the constructions carried on CNC machining centre, 4. Parallel operation of hydraulic cylinders, 5. Compact and mono block hydraulic system, 6. Pressure relief valves to eliminate the risk of access pressure rise, 7. High strength hold-down system with pressure adjustment, 8. Illumination of blades, 9. Cutting length adjustment, 10. Highly wear resistant and tough blades, made of imported European steel with 2 cutting edges of upper blades and 4 cutting edges in lower ones, 11. Position switch for different modes of operation, 12. Light beams at the rear side, 13. Emergency stop and reset facilities, 14. Motorised back gauge and position controller with ± 0,1 mm. positioning accuracy.II.1.2 Technical features
  10. 10. HGM 2504 3006 3008 3010 3013 3016 3020 4006 4008 4010 4012 4014 4016 6006 6008 6010Cutting Capacity 4 6 8 10 13 16 20 6 8 10 12 14 16 6 8 10 mm.Cutting Lenght A 2550 3050 3050 3050 3050 3050 3050 4050 4050 4050 4050 4050 4050 6100 6100 6100 mm.Shearing Angle 1,5 1,5 1,9 2 2,1 2,25 2,75 1,5 1,5 1,5 1,8 1,8 2 1 1 1,1 DegreeHolddown Cylinders 10 12 13 14 14 17 17 17 17 17 18 18 18 26 27 28 UnitStrokes Per Minute 30 18/30 20/35 13/19 10/14 7/10 7/10 10/14 13/20 11/17 9/15 6/20 5/16 9/12 10/16 6/10 min.Clearance Between Columns B 2700 3230 3230 3240 3240 3280 3280 4230 4240 4240 4320 4350 4375 6250 6300 6350 mm.Height of W orktable C 850 850 850 850 850 850 900 850 850 900 900 900 900 900 900 900 mm.Widht of Worktable D 400 500 580 600 620 625 655 600 630 635 660 660 680 750 750 750 mm.Throat Depth E -- -- 250 250 250 200 150 250 250 250 250 250 100 250 100 100 mm.Overall Length F 3800 4300 4300 4350 4400 4450 4450 5340 5370 5350 5450 5450 5480 7350 6800 6900 mm.Overall Height H 1400 1600 2120 2200 2400 2400 2600 2130 2200 2380 2400 2400 2420 2350 2350 2500 mm.Overall Depth (excl. Front supports) G 2100 2620 3050 3100 3150 3250 3450 2900 2950 3050 3300 3300 3350 3050 2350 2500 mm.Oil Tank 140 160 230 230 230 315 350 220 220 280 370 370 370 230 350 400 lt.Motor Power 11 11 15 22 22 30 45 11 22 22 30 30 30 15 22 37 Kw.Weight (Approx.) 4,5 6 8 10 12,5 16,5 21 11 13 18,5 19 20 25 25 27 30 Ton ● Special capacity machine can be manufactured upon request. ● Technical specifications are subject to change without notice.
  11. 11. II.1.3 Remarks1. The hydraulic pump must never be run without oil, since it will be damaged. The oil level must always be checked before starting the motor.2. Any adjustment on hydraulic valves may only be permitted by manufacturer’s notice.3. Electrical and mechanical connections, which are not made properly by qualified personnel, will be at customer’s risk.4. The customer will make sure that there is a minimum of 500 lux local lighting or daylight at the blades area.II.2. SAFETYII.2.1 Instructions• The capacity of the machine must not be exceeded.• Only one piece of sheet must be cut at each cutting stroke.• Only properly qualified personnel may operate the machine.• Before starting the machine all area around the machine must be cleared of obstacles which may cause falling, tripping or slipping hazards.• Operation manual of digital position control unit must be well understood and referred by the operators. Refer to Appendix D.• Operator must be sure there is no one behind, within or on the machine while operating.• Safety is maintained by fixed guards at the front part of the tools area and at the side gaps. At the rear part, 3 light beams maintain control for entrance to the work area.• The limit switches at top and bottom points prevent excessive and continuous pressure rise, which also prevents temperature rise of the oil.• Adjustment mode for adjustment of blade gap after grinding.• Operators should take care of the control panel and foot pedal cable not to be damaged during handling of material or due to any misuse or falling objects.• Electrical cabinet shall be kept close during operation. Anyone except the properly qualified maintenance personnel is not allowed to open it anytime.• It is forbidden to hold naked flame against the machine, or to carry on welding or grinding of the work pieces on or around the machine.• The operators should wear according to the related regulations. (ie. durable clothing, which does not hang loose, as well as industrial shoes with steel toecaps, industrial gloves etc.)• During the maintenance and repair work, the main switch shall be turned off to the “0” position and locked by a padlock for safety reasons.• In case it is needed emergency stop buttons are available on the foot pedal stand and on control panel. 9
  12. 12. II.2.2 Safety EquipmentsII.2.2.1 Control cabinet and electrical switchgear cabinet This switchgear cabinet carries main switch, pedal cable connection and main supplyentrance gland. The control cabinet carries power light, reset button, start button, stopbutton, emergency stop button, position controller, mode selector switch and also a key tolock the control facilities.Attention: The operation manual of position control unit in Appendix D must be completelyread and understood by the operating personnel before starting the machine.II.2.2.2 Fixed guards In the front and at both sides there are guards fixed by bolts. These guards won’t letoperators hand to reach to blades and hold-down cylinders. The distance of these guardsare determined according to the standard.Attention: The fixed guards and other covers around shall never be taken out at operationstage. As this area is the most dangerous part of the machine, any operator shall strictlybe responsible for this.II.2.2.3 Light Beams Light beams are AOPD (active opto-electronic protective device), which form anoptical curtain at the rear side. It is operative if the red indicator lights are on. If there isany obstacle in between sender and receiver units or if they are misaligned, the red lightwill be off and the machine will show an emergency stop characteristics. The distance of the light beams from the back gauge is 1 m. and the referencedistance from blades can be find on the machine plate. It is strictly forbidden to changethe distance lower than the mentioned value. In case there is any deficiency in thestopping behaviour of the system, MVD INAN or the Agent must be contactedimmediately.ATTENTION! Light beams sense the passing of people. It does not sense if there isanyone already inside the machine area. It is full responsibility of the operator to check ifthere is anyone behind or within machine before he resets and starts the machine.II.2.2.4 Safety switch and lock bar Safety switch and the lock bar are placed underneath the down stroking upper beam.The lock bar is pulled out of the housing and the switch pressing on the bar is freed to offposition, and the machine acts like at stop position. Then the bar must be pushed into thehousing on the side column, so that it also maintains a safety means to stop the gravityfall of the beam. But, note that the bar is not designed to bear the weight of the beam notto stop the cylinder force. 10
  13. 13. II.2.2.5 Foot pedal Cutting operations are performed by pressing the foot pedal. When the pedal ispressed the beam moves down. When it is left free, the beam either stops or moves upaccording to the mode of the position switch.2.2.6 Adjustment of cut length The cut length is adjusted by the use of a time relay or a potentiometer placed on thecontrol panel. The system is time based. When the time set by relay or potentiometer isreached the beam automatically stops. Then when the pedal is left free it may move upaccording to the mode position switch.2.2.7 Pressure relief valves Hydraulic system is equipped with several pressure relief valves, which limit themaximum operating pressures at different lines of the system and maintain safe workingcondition.II.2.2.8 Emergency stop button It is used for emergency stops and for stopping at the end of operating the machine.It is designed to stop all movements and controls immediately. To restart, its head mustbe rotated to free. When the reset button is pressed, the white power light will come onand the start button may then be pressed.II.2.2.9 Reset buttons This button is to turn off the reset light. Reset light checks the safety system. In caseof any interruption or fault of the safe guarding system, the system locks the operatingsystem, until the safety related fault is cleared and the reset button is pressed. Note thatthe fault may be due to light beams, safety lock bar switch or emergency stops.II.2.3 Liability MVD INAN hydraulic guillotine shears are designed and produced to cut platematerials. The operator manuals of the machine and back gauge position controller unitmust be the primary basis for using the machine. MVD INAN has no liability for anydamage or its consequences, which is incurred due to the incompetent use of themachine.II.3 OPERATION The shop and machine main switches are turned on and the reset button is pressed.The power light on the machines electrical cabinet shall then come on (if not, control themain supply circuit, light beams alignment and safety bar switch). Pressing start button, 11
  14. 14. the motor will start rotating. If the power light does not come in any case, observe othersafety related components and relays, or contact MVD INAN or the agent.II.3.1 Modes of position switch There are two modes, which can be selected from position switch. First mode is forblade gap adjustment (see section II.3.2) after grinding of the blades and second mode isfor cutting operation at desired length. In the first mode beam moves down as the pedal ispressed and stops when the pedal is left free. For return, position switch is turned to 2ndposition, pedal is pressed and left free. In mode 2, the upper beam moves down when the pedal is pressed and returnswhen it is left free. The beam stroke is limited basically by the machine construction, butalso by upper and lower limit switches. The switch positions are adjusted before deliveryand user will not need readjustment. See also section II.2.6, where the stroke may also beadjusted through a time relay or a potentiometer placed on the control panel.II.3.2 Adjustment of Blade Gap Before starting to cut, the blade gap is adjusted by rotating the arm on the sidecolumn of the machine. The scale and arrow must show the thickness to be cut. Duringthe adjustment, the fixing handles on both sides are loosened at first and then tightenedstrongly after adjustment. The scale around the gap adjustment arm is prepared according to mild steel (St 37-42). When the sheet material is harder, the gap needs to be increased, or when the sheetmaterial is softer, the gap needs to be decreased. Figure 2 gives supportive informationon determination of the gap according to the section of the sheet metal. Note that,excessive opening of the gap with respect to the sheet thickness, may cause the sheetmetal to go in between the upper and lower blades and may damage the beam or thetable. It is suggested to adjust the gap from the scale at ± 1 mm. thickness tolerance. Do not forget to readjust the scale after grinding of blades. For several grindings,only the adjustment of the scale will be enough, but when the thickness of bladestb<15mm, 1 mm. thick sheet metal may be placed behind the blades or the lower bladesupport needs readjustment. (See Figure 3). After grinding and fixing the blades, upper beam must be lowered in the 1st mode ofposition switch and machine must be stopped completely. At this point feeler gauges mustbe used to adjust blade gap to 0,1 mm. and then the scale must be set to 1 mm. It issuggested to check this gap to be precise throughout the whole length. Deviations maycause collision and breaking of the blades. Note also that, there are mechanicallimitations for maximum and minimum gaps, so after setting the scale, these limits shouldbe readjusted to prevent collision of upper and lower blades.II.3.3 Back gauge adjustment Back gauge system is controlled by position controller (See appendix D), which isplaced on the control panel. The calibration and resetting is completed before delivery.The calibration may be made at the minimum position where the back gauge touches thefront limit switch. At this point pressing the stop button of the controller will reset theposition to the datum value in controller parameters. For any problem, the manual of the position controller must be referred. (App.D) 12
  15. 15. ADJUSTMENT OF BLADE GAP The indicator fit around the arm on the left side of the machine is prepared for blade gap adjustment of mild steel St 37- St 42. For harder materials gap may be increased, and for softer materials it may be decreased. 8=0.10 X T ( St 37- St42) SMALL GAP INCREASE THE BLADE GAP. LARGE GAP DECREASETHEBLADEGAP CORRECT GAP DO NOT MAKE ANY EXTRA ADJUSTMENT HAGM 3020 FIGUREMVDvMAKINASANAYIA.$ ADJUSTMENT OF BLADE GAP 2
  16. 16. I I (I( MVDINAN Ill ffi -H----j}--D--0- 1I1I 1J ld ld ld u uu I " c ,L DETAILC SECTION A-A SECTION B-BNV MVD A.$ HAGM 3020 ADJUSTMENT OF BLADE GAP FIGURE 3 MAKiNA SANAVi
  17. 17. II.3.4 Ending the operation Motor stop button is pressed, control lock key is turned off and the key is removed.Main switch is turned off to “0” position. It shall be locked by a padlock when machine isnot operated and also when it is maintained. 13
  18. 18. MVD INAN HGM III. MAINTENANCE MANUAL Maintenance may only be carried by properly qualified maintenance personnel orby a service technician of MVD INAN or the Agent. The machine is designed to carry outmaintenance and lubrication safely. Attention: During the maintenance and repair work, the main switch shall be turned off tothe “0” position and locked by a padlock for safety reasons.Also the lock bar shall be placed into the side column for mechanical safety. See II.2.2.4.III.1 Lubrication Back gauge slide ways and screws must be cleaned and lubricated by oileveryday. Roller bearings must be greased once a week. (See Figure 4) The swing beamaxis must be greased once a month inside for roller bearing and once a week outside forfrictional bearings. During continuous use and heavy work conditions, it is suggested tolubricate them more frequently.Attention: The cylinder joints of the machine will never be lubricated.III.2 Mechanical system maintenance Everyday, the tightness of upper and lower blade bolts must be checked (See Figure3). Every week the blade clearance between the blades must be assured to correspond tothe scale (The clearance will be 10% of the sheet thickness for mild steel). Additionally, tightness of all bolts and nuts on the machine must be checked regularlyevery 15 days and also when there is any irregularity on the operating behaviour. Any other adjustment and problem may be referred to MVD INAN or the agent.III.3 Hydraulic system maintenance Level of oil in the tank must be checked daily. It must be 3-5 cm. below the top cover. The oil must be clean. So, it must be checked that the filter works properly. If filter isdirty, the manometer at the top of the filter will reach the red region. In such case thefiltering element in the filter body has to be replaced. The quality and cleanliness of the oilis of primary concern in hydraulic systems. Improper and dirty oil will shorten the life of thesystem and will cause unexpected problems. After 2000 operating hours or 1 year, whichever is earlier, drain off the oil from the tapat the bottom of the tank. It is suggested to use a flexible hose to connect this point to anempty oil tank or place the tank hole underneath the tap. To refill the machine’s oil tank, the cap at the top surface must be removed. Thefiltering element must be in place to protect fall of materials other than oil. Oil may either 14
  19. 19. !LUBRICATION POINTS. I @121 @121 I I @11] /@11] ,.... @151 Ai. ) @151 -: • • • • • •• • • • • • • • • DETAIL-A @ Grease to be used. 0 Oil to be used. SHELL ALVANIA R3 SHELL ROTELLA 30 or 40 - MOBIL LUX EP-3 MOBIL ENGINE OIL 30 or 40 LUBRICATION CHART. LUBRICATION LUBRICATION SYMBOL POINT FREQUENCY 1 @ Once a week. 2 @ Once a week. 3 0- Everyday 4 0- Everyday 5 @ Once in a month. A HAGM 3020 FIGUREV MVD MAKINA SANAVIA.$ LUBRICATION CHART 4
  20. 20. be pumped by a manual pumping device our poured directly into the hall. The oilmentioned in section I.4 must be used. During this process maintenance personnel shallsupply a ladder or platform and place it safely.Attention: Wear protective clothing while changing the oil. In addition to change of oil, the element of the filter shown in the hydraulic diagramshall also be replaced every year. Other hydraulic elements may be ordered regardingthe drawings in Appendix B: Hydraulic System 15
  21. 21. Appendix A: Explanatory wordlistHydraulic swing-beam guillotine shear: Machine designed to transmit energy to themoving beam by hydraulic means principally for the purpose of shearing of sheet metalbetween blades along straight lines.Beam: Main reciprocating machine member, which holds upper blade.Table: Stationary table which holds lower blade.Upper blades: Blades with cutting edge less than 90º.Lower blades: Blades with 90º cutting edges.Cut cylinders: Placed one on each column and turns hydraulic pressure to mechanicalforce and exerts it onto the beam to cut the sheet metal.Return cylinders: Cylinders which move the beam up.Back gauge: The gauge against which the plate to be cut is positioned to maintain the cutwidth all along the cut length. Its position is adjusted by the position controller on thecontrol panel. 16
  22. 22. APPENDIX B: Hydraulic system and equipments 17
  23. 23. -l I I I 1.11 I I 1 M.114e--------. I I 3 1.12 I I - P314" - 121114• j ?MZA MALZEME ?ZENKONTROL ADETONAY 1 iL EK RES?M NO BH-026
  24. 24. NU. I PART NAHE I REHARKS 01 I HYDRAULIC CYLINDER 02 COHPACT SEAL (B+S PCBOA-2000NCROQ) 03 BEARIN6 BAND. (2,5X15 C380) 04 I BEARIN6 BAND {2,5X25 C380) 05 I O-RIN6 (tb3,53X196,2) 06 I SUPPORTIN6 RIN6 tb(196,2X202,5)11,25 07 I NUTRIN6 tb(120X140)116 08 I SUPPORTIN6 RIN6 tb(120X140)13 PAGEMVD HAGM 3013 GROUP NU. NUVMAKIN A SANAVI A.!j LEFT CUTTING CYLINDER
  25. 25. 1 4 9 "-- - ""-+--- --------------------- NU. I PART NAHE I REHARKS 01 I HYDRAULIC CYLINDER 02 COHPACT SEAL (B+S PCBOA-2000NCROQ) 03 BEARIN6 BAND. (2,5X15 C380) 04 I BEARIN6 BAND {2,5X25 C380) 05 I O-RIN6 (tb3,53X196,2) 06 I SUPPORTIN6 RIN6 tb(196,2X202,5)11,25 5 7 8 07 I NUTRIN6 tb(120X140)116 08 I SUPPORTIN6 RIN6 tb(120X140)13 PAGEMVD HAGM 3013 GROUP NU. NUVMAKIN A SANAVI A.!j RIGHT CUTTING CYLINDER
  26. 26. 02 NU PART NAME /BRAND CODE 01 PISTON ARM 02 BODY 03 PISTON 04 SPRING 05 CONNECTION FLANGE 06 NUTRING (/)(27X36)/6 PU KASTA$ K21-027/1 07 D-RING (/)2X15 08 1116 NUTHv MVD MAKINA SANAVIA. HAGM 3020 HOLDDOWN CYLINDER FIGUR E
  27. 27. HGH 3016-........
  28. 28. APPENDIX C: Electrical system and equipments 18
  29. 29. APPENDIX D: Digital position control unit 19
  30. 30. Delem DAC-350Operation manual Version V7 U:UitgavebestuurhandleidDAC-350V7dac350_gb.WPD Manual version V0504
  31. 31. DelemPREFACEThis manual describes the operation of the Delem control type DAC-350 and is meant foroperators who are instructed for operation of the total machine.Only authorised people should be able to create new or edit existing programs.The control has therefore a keyswitch to prevent uncontrolled programming. With the keyswitchin the off position the operator can only execute a selected program but not change the parametersto wrong, unwanted values. V0297, 0.2
  32. 32. Delem DAC-350 OPERATION MANUALCONTENTS PAGEPREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.31. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 1.1. Operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 1.2. Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22. Frontpanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13. Programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 3.1. Data preparation/Data editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 3.1.1. General program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 “ Product copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 3.1.2. Specific step parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 3.1.3. Programmable on/off outputs per step. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7 3.2. Program selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 3.3. Program constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9 “ Page 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9 “ Page 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10 “ Page 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11 “ Page 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13 “ Page 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15 “ Page 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16 “ Page 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.17 3.4. Backup and Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.184. Automatic production mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 “ Service screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.45. Manual production mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 “ Service screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 V0504, 0.3
  33. 33. Delem1. Introduction1.1. Operation modesThe DAC-350 is a programmable backgauge control which allows programming the backgaugeposition and several function parameters. The control can specifically be used as shear controlincluding angle, gap and stroke control. The angle, gap and stroke control are optional axes whichcan be enabled depending on the application of the machine.If enabled the angle, stroke length and gap settings are automatically calculated. These calculationsdepend on the programmed sheet thickness and the used material.It is possible to create your own programs step by step in a userfriendly way via menu drivenprogramming: - Programming mode for preparing or editing your data.The DAC 350 has 2 operating modes: - automatic mode, to run a complete program consisting of a set of steps with several programmable parameters. - manual mode, to run one set of parameters for single cuts. The programmed parameters and the backgauge position are controlled after pushing the start-button. The backgauge, angle and gap can also be displaced manually by means of the handwheel.Manual movement: - By pushing this key the handwheel will be activated for manual movement of the available axes.Each of these modes can be selected with the mentioned frontpanel pushbuttons. The selected modewill be indicated with a lightning LED in the pushbutton. V0899, 1.1
  34. 34. Delem1.2. OptionsOptions are machine-dependent. They can be installed later as upgrades, to add additionalfunctionality to the controller.The following options are available.Floppy driveThe DAC-350 can be equipped with a floppy drive unit for 3½” HD floppy disks to read or writeprograms to or from disk.Serial communicationThe DAC-350 can be connected to a pc for serial communication. If this option is installed,communication settings must be programmed.Load positionA load position can be programmed in the controller. Then the backgauge will move to apreprogrammed position to allow loading of a product, before moving to the first position of acutting program. V0899, 1.2
  35. 35. Delem2. FrontpanelThe frontpanel with LCD display consists of the following items:- Display: Monochrome LCD-screen including backlight.- Mode keys including LED indication: | | | Manual mode Programming mode Automatic mode Start button Stop button - handwheel selection button- Keyboardcursor up key,to select the previousparametercursor down key, 10 numerical keys (0-9)to select the nextparameterTo leave aprogramming plus/minus toggleselection enter key, to confirm a programmed value decimal point clear key, to delete an input value V0297, 2.1
  36. 36. Delemprevious next • Select/delete programstep step • parameter overview in „hand-mode‟ and „auto-mode‟. - Key switch, with position "1" for free programming and position "0" to prevent the programming of new programs or changing existing programs. V0297, 2.2
  37. 37. Delem3. Programming mode - Select the programming mode by pushing the indicated key. The programming mode is active when the LED in this key is on. Programming can only be done when the controller is in stopped position.You will see the following menu-overview on the screen:The programming possibilities can be selected by entering the required number and pushing theenter key. 1= DATA PREPARATION . . . . . . . . . . . . . . . . See paragraph 3.1 This selection is to create a new, non-existing program. 2= DATA EDITING . . . . . . . . . . . . . . . . . . . . . . See paragraph 3.1 This selection is to change an existing program. This program is the actual program in the automatic production mode and can be selected from the memory by menu number 3. 3= PROGRAM SELECTION . . . . . . . . . . . . . . . See paragraph 3.2 This choice will give an overview of the programs as stored in the memory. The available programs are listed by the programnumber. 4= PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . See paragraph 3.3 This choice will list general parameters like inch/mm-selection, programming language etc. 5= BACKUP AND RESTORE . . . . . . . . . . . . . . See paragraph 3.4 To write programs to floppy disk or read programs from it. This function is optional. If option 5 is available, press this key to make it visible. V1198, 3.1
  38. 38. Delem3.1. Data preparation/Data editing3.1.1. General program parametersFor creating a new program the following parameters will appear on the screen to be programmed.• Program number The programnumber is a free programmable number of up to 4 digits. Range: 0 - 9999• Material type Four material types can be selected. The material type will be used for angle and gap calculation. The corresponding angle and gap values depend on the manufacturer settings. Range: 1 - 4• Materialthickness The thickness of the used material. Range: 0.1 - maximum thickness. Maximum value depends on the corresponding machine parameter setting.• Retract distance The programmed retract distance for the backgauge will be executed in every step of the program. Range: 0 - maximum backgauge position. Maximum value depends on the corresponding machine parameter setting. This parameter is only shown if the Retract function is used. V0899, 3.2
  39. 39. DelemX-CorCorrection of the X-axis position, valid for each step. This correction also applies to the X2-axis,if installed.Range: -9.9 - 9.9 mmLoad (optional)To determine whether or not to use a load position for this program. Only possible, if this optionis installed.0 = no load position1 = use load position 12 = use load position 2The load positions can be programmed with the parameter Load Position in menu 4, Parameters.OffsetSheet position offset. This programmable offset is meant to take sheet displacement on the table intoaccount. In other words, the operator may place the sheet on a desired place on the table. The offsetmust be programmed according to the required sheet position as shown in the picture below:When programming the parameter "SHEET POSITION OFFSET", the following steps are carriedout:• all "stroke" value(s) will be adapted in cutting programs;• the control checks in each program step whether the sum of "LENGTH" and "SHEET POSITION OFFSET" is greater than the maximum cutting length. If so, the error message ** OFFSET + LENGTH > MAX LENGTH ** will be generated.When the "Sheet Position Offset" value is greater than 0 (offset is active ), the symbol is shownin the production modes as a reminder for the user that the sheet has to be placed on the correctposition. V0504, 3.3
  40. 40. Delem“ Product copyWhen you are in „DATA EDITING‟ you can copy the active product.Go with the cursor keys to the parameter PROG-NR.Type the new product number and confirm with the ENTER-key.The controller displays the following message (see figure below).If you choose 1, then the new product number is active.3.1.2. Specific step parametersAfter entering the retract distance, the parameters for the first step will appear on the screen.• Length. The material length to be cut. Range: 0.0 - 10000 mm• Backgauge position XM. The required backgauge position must be entered at this parameter. Range: minimum position - maximum position It is also possible to enter a negative value for XM. In that case, the value is interpreted as a displacement value (chaining). This value is then substracted from the actual X-axis position. This can only be done to move to a lower position and is not allowed at the first V0504, 3.4
  41. 41. Delem step.• Second backgauge position X2 (OPTIONAL) When the backgauge (or frontgauge) is equipped with a second axis, then the position can be programmed with this parameter. Default value is equal to the programmed value of XM. X2 can be adjusted afterwards. Range: minimum position - maximum position• Repetition. The number of times that the programmed step is repeated before the next step will be executed. Range: 0 - 999 The value 0 can be used to indicate that the programmed step must be skipped. This cannot be done for the first step of a program. The repetition number is also used for the number of chained dimensions to be executed.• X Speed Speed of the X-axis, which can be programmed differently for each step in a percentage of the maximum speed. Range: 0 - 100 %The specific shear parameters for the optional axes cut-angle, cut-gap and cut-stroke are onlypresent if one or more of these optional axes have been activated.• Angle (α) Automatic calculated angle, which can also be changed within the program for every step. Range: 0 - maximum possible angle• Gap (G) Automatic calculated gap distance, which can also be programmed differently for every step. Range: 0 - 9.99 mm• Stroke (S) Stroke limit of the cut. Range: 0 - maximum possible stroke• Z-axis position (OPTIONAL) When the backgauge is equipped with a Z-axis, then the position can be programmed with this parameter. V0504, 3.5
  42. 42. Delem Depending on the machine configuration the Z-axis position - can automatically be computed or - can manually be programmed The computed value is determined by the following formula: Auto computed value Z-axis = value „length‟ - „Z-offset‟ Type Enter to accept the computed value. The „Z-offset‟ parameter is to be programmed in the program constants. Range: minimum position - maximum position• Cutting force Force with which the plate is cut. A calculated value is offered, based on plate material and thickness. You can accept the offered value or program another value. Only available if pressure control is installed on the machine.• Clamping force Force with which the plate is clamped on the table. A calculated value is offered, which is a percentage of the cutting force. You can accept the offered value or program another value. Only available if pressure control is installed on the machine. V0504, 3.6
  43. 43. Delem3.1.3. Programmable on/off outputs per step.There are either 4 or 8 independent, programmable outputs available. These outputs are freelyprogrammable for any required purpose. The number of available outputs (4 or 8) depends onmachine settings.• F1 - F4 / F1 - F8 Range: 0 - 1 in which "0" means off and "1" means on (function output active)• F This parameter is the decimal value, calculated from the combined binary value of the function outputs. F1 is the least signifcant bit (LSB), F4 (or F8) is the most significant bit (MSB). When one of the function parameters F1 - F8 is changed, the resulting value F is automatically changed as well. When F is changed, the parameters F1 - F8 are also changed accordingly. In case the outputs are used for binary combinations, programming F is more user-friendly. Whether or not this parameter is available depends on machine settings. Range: 0 - 15 or 0 - 255After the last input of all the parameters in the first step the question appears if a new step isrequired. Entering zero will stop further programming and with 1 a next step will be added to theprogram. This question will only appear in the data preparation mode. The maximal number of stepsper program is 99. V0504, 3.7
  44. 44. Delem3.2. Program selectionWith choice number 3 in the menu the overview of the available programs in the controller memorywill be listed.An existing program can be selected by entering the required number. A program can be deletedby pushing the key and entering the program to be deleted: this key has a toggle function andmust be pressed again to return to the selection mode.It is also possible to delete all the programs at once. In the delete mode you have to program“-1". After the confirmation of this choice with the enter-key the controller returns with a question.When you select „1 the contents of the program memory is erased.When you have created more programs than can be listed on one screenpage, you can list the nextpage with help of the -keyIn the upper right corner the used memory contents with respect to the memory capacity will beindicated in a percentage value. V0297, 3.8
  45. 45. Delem3.3. Program constantsThe controller has specific operator selectable and adjustable parameters which are divided overfive pages.Software versionAt the right hand side in the upper part of the first four screens the version number of the controllersoftware is mentioned. Example: V7.1“ Page 1.• Inch select 1/0 (IS) The programming unit for the backgauge position, the actual position read-out, the retraction value, material thickness, the material length, gap and stroke can be set in mm or inches. 0 = mm 1 = Inches• Language selection (LG) The following languages can be selected: 0 = English (GB) 1 = German (D ) 2 = Danish (DK) 3 = French (F ) 4 = Italian (I ) 5 = Dutch (NL) 6 = Finnish (FI) 7 = Czech/Slovak (CS) 8 = Spanish (ESP) V0504, 3.9
  46. 46. Delem“ Page 2.• Shear stress material 1-4 (S1-4) Material constant, used for calculation of cutting force. The following table shows the default values for these parameters. You can change these values if necessary. Nr. Name Shear stress value [KN/mm2] 1 Steel 80.0 2 Aluminium 26.0 3 Zinc 0.253 4 Stainless Steel 87.0• Clamping force factor (CF) Calculation factor of the clamping force, programmed as a percentage of the cutting force. V0504, 3.10
  47. 47. Delem“ Page 3.• Chaining mode (CH) You can set by this parameter if the incremental value must be subtracted from the previous target position or the actual position: Xn+1 = Xn target - Xincr. or Xn+1 = Xn actual - Xincr. 0= New position is relative to previous programmed position 1= New position is relative to actual position• Stockcount mode (CN) To set for the stockcounter in up- or downcounting direction. In the downcounting mode, the controller will go automatically to stop when "zero" has been reached. Range: 0= downcounting 1= upcounting V0504, 3.11
  48. 48. Delem• Z-offset (ZO) The Z-offset is the distance between the plate side and the Z-axis. Default: 10mm. Range: 0 - 999mm. Only used in case of automatically computed Z-axis position.• Load position (L1/L2, optional) X-axis position for loading products in case the load position option is used. The use of a Load position can be activated in a program. If it is active and a program is started, the X-axis will move to the load position before moving to the position of the first step. Range: 0 - 16000 mm V0504, 3.12
  49. 49. Delem“ Page 4.• X-reference correction (CR) When the display gives a backgauge position which does not correspond with the actual mechanical position, the difference can be corrected by this parameter value. Program the calculated difference. Range: -99.99 - +99.99 mm Default: 0.00 Example: When the programmed and displayed value = 250 and the actual, mechanical position value = 252 the CR parameter = -2.• X2-reference correction (C2) When the display gives a X2-backgauge position which does not correspond with the actual mechanical position, the difference can be corrected by this parameter value. Program the calculated difference. Range: -99.99 - +99.99 mm Default: 0.00 Example: When the programmed and displayed value = 250 and the actual, mechanical position value = 252 the C2 parameter = -2.• Z-reference correction (CZ) When the display gives a Z-axis position which does not correspond with the actual mechanical position, the difference can be corrected by this parameter value. Program the calculated difference. Range: -99.99 - +99.99 mm Default: 0.00 Example: When the programmed and displayed value = 250 and the actual, mechanical position value = 252 the CR parameter = -2. V0504, 3.13
  50. 50. Delem• Auto X-ref. search (AR) After switching on the controller and pressing start, the backgauge will search automatically for the reference position. It is also possible to disactivate this automatic reference search. This means that the controller will memorize its actual backgauge position after power down. Range: 1 = automatic reference search always. 0 = memorisation of the backgauge position Default: 1 V0897, 3.14
  51. 51. Delem“ Page 5.Communication Parameters (optional)Serial communication is an option that can be installed on the controller. If installed, the followingparameters can be programmed. For successful communication, both sides of the serial link musthave similar communication settings.• Parity 0/1/2 (PY) Parity check for serial communication: 0 = none 1 = odd 2 = even• Stop bits (SB) The number of stop bits (1 or 2) V0899, 3.15
  52. 52. Delem“ Page 6.• Baudrate (BR) To set the proper baudrate for communication: 1 = 300 baud 2 = 600 baud 3 = 1200 baud 4 = 2400 baud 5 = 4800 baud 6 = 9600 baud V0899, 3.16
  53. 53. Delem“ Page 7.Maintenance viewThe last page in the parameter constants has been reserved for maintenance information. This pagecan be found using the -key in the parameter constants selection.These parameters can not be programmed, or changed.• Hours The machine hours, running machine will be indicated.• Nr strokes The number of strokes that the shearing beam has made will be indicated. V0897, 3.17
  54. 54. Delem3.4. Backup and RestoreIf this option is installed, it is possible to save programs on a floppy disk or read them from it. Afterpressing 5 in the main menu, the “Backup and Restore” menu appears.BackupTo make a backup, choose 1 in the “Backup and Restore” menu. An overview appears of allprograms that are stored in the controllers‟ memory.Type the number of the program that you want to save on floppy disk and press <enter>. Theprogram is now saved to floppy disk. If a backup was succesfull, the number will be marked witha „>‟ sign. If not, a message will appear that the backup did not work and the number will be markedwith a „-‟ sign. In case a program under the same name already exists on the floppy disk, thecontroller will issue a warning on the screen. Then you can choose either to replace that programwith your backup (1) or to cancel the backup operation (0).To save all programs, press „0 and then <enter>. The program will ask for a confirmation bypressing „1‟. If some of the programs already exist on the floppy disk, they will be replaced. Themarkings „>‟ and „-‟ will appear to indicate whether a backup was succesfull or not. V1198, 3.18
  55. 55. DelemRestoreTo restore a program from floppy disk, choose 2 in the “Backup and Restore” menu. An overviewappears of all programs that are stored on the floppy disk.Type the number of the program that you want to read from floppy disk and press <enter>. Theprogram is now loaded into the controller. If a restore was succesfull, the number will be markedwith a „>‟ sign. If not, a message will appear that the restore did not work and the number will bemarked with a „-‟ sign. In case a program under the same name already exists in the controllermemory, the controller will issue a warning on the screen. Then you can choose either to replacethat program with the new program from floppy disk (1) or to cancel the restore operation (0).To load all programs from the floppy disk, press „0 and then <enter>. The program will ask for aconfirmation by pressing „1‟. If some of the programs already exist in the controller, they will bereplaced. The markings „>‟ and „-‟ will appear to indicate wheter a backup was succesfull or not.In the upper right corner of the screen is indicated the percentage of memory that is occupied by theexisting programs in the controller. Watch the amount of memory that is occupied before loadingmore programs in the controller. Make a backup on another floppy, if necessary. V1198, 3.19
  56. 56. Delem4. Automatic production mode - Select the automatic mode by pushing the indicated key. The required program to be made in production should be first selected in the programming menu choice 3.In automatic mode you will see the following screen in the started situation.In this screen you see in the upperrow the following information from left to right: - Step 1/10: 1 Indicates which step is the actual step. 10 Indicates how many steps are included in the selected program. - Rep 1/3: 1 Indicates which step is actual of the total repetitionnumber. 3 Indicates how many times the actual program step should be repeated. - Prog 1234: Indicates the selected programnumberIn the rest of the screen the programmed backgauge position XM is displayed and at the right sidethe actual position X.The stockcount parameter QM can be set to the required number of products and the actualproductcounter Q is displayed at the right side. V1198, 4.1
  57. 57. DelemThe other values for the programmed parameters like thickness, materialtype, etc. can be checkedby pressing the -key:The parameters cannot be changed in this field. Editing the program can only be done via the menu-selection 2. By pressing the -key you get the next page with parameters.To return to the backgauge position and stockcountinformation (main screen „auto‟-mode) the -key should be pressed again (toggle function). V0899, 4.2
  58. 58. DelemBy pressing the -key you activate the manual movement menu in which you can adjust theX-axis with the handwheel. This option is only active when the controller is in the „stop‟ mode, andcan be used as „teach-in‟ function.By pressing the -key or the cursor key you can adjust the angle and the gap (teach in).To return to the mainscreen of the „auto-mode‟ press the -key again (toggle function) V0897, 4.3
  59. 59. Delem“ Service screensWhen you push the END-key in the mainscreen of the „auto‟- mode (not handwheel selection) astatus-overview for service purposes is displayed (two screens).After pushing the END-key again you return to the main screen of the „Auto‟-mode (togglefunction). V0897, 4.4
  60. 60. Delem5. Manual production mode - Select the manual mode by pushing the indicated key. This mode gives the possibility to program all parameters for a single step. This mode can be used for test cuts or fast programming of single cuts.The following screen is then active in the started situation.The stockcount value can be programmed directly in the zoomed picture.The backgauge position X can be programmed in the parameters of this single step and the controlwill drive the backgauge to that position after starting the control and displaying abovementionedscreen. Also the other parameters can be programmed like the "auto-mode".With the -key you get the parameter overview (first page). This is a toggle function. V0897, 5.1
  61. 61. DelemThe angle, gap and stroke parameters are automatically computed.By pressing the cursor key or the -key you get the next page with parameters.By pressing the -key (toggle function) you get the manual movement menu in which youcan adjust the X-axis with the handwheel. This option is only active when the controller is in the„stop‟-mode. V0899, 5.2
  62. 62. DelemWith the cursor key or the you can adjust the angle or the gap (teach in function). V0897, 5.3
  63. 63. Delem“ Service screensBy pressing the END-key (only at the thickness parameter) in the parameter overview menu of thehandmode you get a status-overview for service purposes (two screens).Again pushing the END-key results in the main parameter screen of the handmode (togglefunction). V0897, 5.4

×