Successfully reported this slideshow.

More Related Content

Related Books

Free with a 14 day trial from Scribd

See all

3 doodler

  1. 1. 3Doodler The World’s first 3D writing pen MD Arshad Shareef
  2. 2. CONTENTS  WHAT IS 3DOODLER?  KNOW YOUR DOODLER  STEPS TO USE 3DOODLER  TURN ON DOODLER  LOAD THE PLASTIC  SELECT THE SPEED  DOUBLE CLICK FOR CONTINUOUS FLOW  UNLOAD THE PLASTIC  SPECIFICATIONS  USES  CONCLUSION  REFERENCES
  3. 3. WHAT IS 3DOODLER?  The 3doodler is a first 3D pen developed by Peter Dilworth and Maxwell Bogue of WobbleWorks LLC.  It is capable of drawing in the air or on surfaces.  The 3D printing pen uses ABS plastic which is the same material used by many 3D printers.  The 3Doodler contains a mains-powered electric heater that melts plastic which then cools as it comes out of the end of the pen like a cake-icer
  4. 4. KNOW YOUR DOODLER 1. Nozzle 2. Extrusion Speed Control (Fast) 3. Extrusion Speed Control (Slow) 4. Cooling Fan 5. LED Indicator 6. Power Cord 7. Maintenance Cover 8. Cleaning Tool 9. ON/OFF Switch 10. Temperature Adjuster 11. Control Port 12. Plastic/Filament Loader 13. Mini Screwdriver 14. Nozzle Removal Tool
  5. 5. STEPS TO USE 3DOODLER: 1. Plug in your pen and turn it on. 2. Allow your doodle to heat up before loading plastic/filament 3. Load the pen 4. Extrude/Select your speed 5. Double click for continuous flow 6. Unloading/Reversing the plastic filament
  6. 6. TURN ON DOODLER • Turn the pen on by selecting the correct heating temperature for the type of plastic/filament you are using. • Set the slide switch to HI (“High”) for high temperature plastics/filaments like ABS or FLEXY, or LO (“Low”) for low temperature plastics/filaments like PLA or WOOD. • The 3Doodler takes approximately 1.5 minutes to heat up. During that time the LED indicator will be RED and it will not be possible to use the pen. Once the correct melting temperature is reached and the pen is ready, the LED indicator will change to BLUE (HI) or GREEN (LO)
  7. 7. LOAD THE PLASTIC  Load the plastic/filament into the plastic loader at the back of the pen, feeding it down the length of the 3Doodler until you feel it gripped by the gears inside the pen. It can take up to 30 seconds for a newly loaded strand to begin extruding from the nozzle of the pen.  If you do not feel the plastic/filament being gripped by the gears inside the pen, please give it a gentle clockwise twist while pushing it down the shaft of the 3Doodler.
  8. 8. SELECT THE SPEED Press and hold the button for the desired extrusion speed (FAST (3) or SLOW (4) ) and wait for the heated material to emerge from the pen tip. Releasing the chosen speed button will cause the pen to stop extruding the heated material.
  9. 9. DOUBLE CLICK FOR CONTINUOUS FLOW • Your 3Doodler can be set to continuously extrude plastic/filament without you having to hold down on the extrusion buttons. Simply double-click on the desired extrusion speed (FAST (3) or SLOW (4) ) and your 3Doodler will continuously extrude plastic/filament for up to ten minutes before stopping. • To stop the continuous flow of plastic/filament, simply click on either the FAST (3) or SLOW (4) button on your 3Doodler. • To temporarily pause the continuous flow of plastic/filament, hold down on either the FAST (3) or SLOW (4) button on your 3Doodler and then release to resume continuous flow.
  10. 10. UNLOAD THE PLASTIC • Hold down BOTH the FAST (3) and SLOW (4) extrusion buttons at the same time. The LED indicator (5) will flash. • When the plastic/filament stops moving in reverse you may gently take it out from the back of the pen .
  11. 11. SPECIFICATIONS • Output Power: 6W • Output Voltage: 5V • Input Voltage: 5V
  12. 12. USES There are many ways 3Doodler can be used. Some of them are:  Basic 3D shapes and 3D models.  Jewellery, pendants and hanging ornaments  Decorative art and fridge magnets  Personalization of everyday objects (iPhone cases, laptops, pens, etc.)  A mini Eiffel Tower or a soccer pitch for your Lego men  And much much more…
  13. 13. CONCLUSION  3Doodler can be used whether you are an artist, hobbyist or 3D printing fanatic.  3Doodler is not a toy. The recommended age for use of it is 12.
  14. 14. REFERENCES  http://the3doodler.com  http://3dprintingsystems.com/products/3doodler/  http://www.telegraph.co.uk/technology/technology- video/9882624/3Doodler-explained-how-the-3D-printing-pen- works.html

×