7.molding and casting composites (mar 7)

851 views

Published on

7.molding and casting composites (Mar 7)
WALTER GONZALES ARNAO

Published in: Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
851
On SlideShare
0
From Embeds
0
Number of Embeds
84
Actions
Shares
0
Downloads
5
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

7.molding and casting composites (mar 7)

  1. 1. MOLDING, CASTING AND COMPOSITES(MAR 7)FAB ACADEMY 2012 WALTER GONZALES ARNAO
  2. 2. SUMMARY THE JOB IS TO MAKE A 40X30 40X PART IN A MECHANICAL WAX MOLD, USING THE MACHINE ROLAND CLASS 7 . molding and casting composites (Mar 7)
  3. 3. FIRST JOB IN THE SOFTWARE IS DRAWING TO DEFINE THE GEOMETRY OF THE PIECECLASS 7 . molding and casting composites (Mar 7)
  4. 4. STEP TWO. INTRODUCED THE SAVE THE FILE TO STL Open it THENTHE SOFTWARE THAT MADE LAQUINA MACHINING WITH STRAWBERRY3mm FLATCLASS 7 . molding and casting composites (Mar 7)
  5. 5. STEP THREE. IS THE SIMULATION SOFTWARE IN THE MACHINE TO SEE THE PATH OF THE STRAWBERRY IN THE WAX ​PEZA machinableCLASS 7 . molding and casting composites (Mar 7)
  6. 6. STEP FOUR. STANDING IN THE STRAWBERRY 3mm MACHINE TOPROCEED TO MACHINING
  7. 7. STEP FIVE. PULLS THE PART OF THE ROUTER PAR WAXPROCEED TO REMOVE THE WAX ​TO LET TAILINGS CLEAN
  8. 8. STEP SIX. APPLICANTS ARE TO FIT THE MOLD Mescla FLEXIBLE
  9. 9. step seven, we proceed to give the flexible part assembly that will be the modeCLASS 7 . molding and casting composites (Mar 7)
  10. 10. step eight, the flexible mold is prepared to fill it with whitecement
  11. 11. Step nine, white cement is placed and then is expected todisassemble
  12. 12. step ten, is corrected by removing faults early, mold
  13. 13. step eleven, final partCLASS 7 . molding and casting composites (Mar 7)
  14. 14. step twelve, TESTS WITH OTHER MATERIALSCLASS 7 . molding and casting composites (Mar 7)
  15. 15. part 1 part 2 part 3 (mold A) step thirteen -WHEN MAKING URETHANE MOLDS, I PROPOSED THAT THE PIECE OF URETHANE. -TO SEE HOW IT WORKS. -THE FIRST TEST HIT THE MOLD RELEASE AGENT BECAUSE I DID NOT PAY (MOLD A AND B)CLASS 7 . molding and casting composites (Mar 7) (mold B)
  16. 16. Step fourteen -SHOWS THE MOLD PART -THIS PIECE WAS USED IN MOLD RELEASECLASS 7 . molding and casting composites (Mar 7)
  17. 17. Step fifteen -THE DETAIL OF EACH PIECE AND THE MOLDCLASS 7 . molding and casting composites (Mar 7)
  18. 18. CONCLUSIONS.1. EL TRABAJO EN MOLDEADO PERMITE EXPLORAR EN LA FORMA Y LA APLICACION DE MATERIALES.2. THE TECHNOLOGY USED IN THE MOLDING ALLOWS EXPENSIVE PIECES AT CRAFT.3. THE LIMITATION IS THE TYPE OF MATERIAL USED BECAUSE IT IS IMPORTED FROM USA4. BUT COULD BE REPLACED WITH ALTERNATIVE MATERIALS EXISTING IN PERU, WHICH SERI ANOPPORTUNITY TO INVESTIGATE ALTERNATIVE MATERIALS.CLASS 7 . molding and casting composites (Mar 7)

×