Electrical and Panel Systems
•
3 likes•1,043 views
This presenation details electrical for use in panel systems. If you have any questions about this pesentation please reach out to alibia.devente@gmail.com
Recommended
Recommended
More Related Content
Viewers also liked
Viewers also liked (20)
Similar to Electrical and Panel Systems
Similar to Electrical and Panel Systems (20)
More from Alibia de Vente
More from Alibia de Vente (20)
Recently uploaded
Recently uploaded (20)
Electrical and Panel Systems
- 1. We will be starting momentarily. For Audio Please Dial: Conference Call 888.481.3032 Passcode 75892620# Press *6 to mute phone on/off
- 4. Definition of a Circuit
- 5. Electrical Circuit Configuration Options
- 6. Cetra Power and Data Statement of Line Page 19
- 7. Cetra Overview Page 20 Panel Thickness is 2 5/8” Power and Electrical run in the base.
- 8. Cetra Mid-Wireway Panel Page 22 Provides the ability to bring electrical and data to worksurface height. The vertical wireway is 2.6 sq.” and is located 14” from one edge of the panel. It is necessary to use mid-height connectors to continue power at a connector. A powered mid-height panel on ships with one harness. Image taken from installation instructions.
- 11. Cetra Ceiling Entry Panel Page 23 Ceiling Entry panel is at 68” and 80” heights widths is 30 - 48. You have the ability to go higher with stack, this option gives a cleaner look. Ceiling entry is specified separately from panel. Images taken from installation instructions.
- 12. Cetra Power and Data Overview Page 36
- 13. CetraJumper Cables Page 37
- 14. Cetra Hardwire Panels Page 44
- 15. Cetra 8-wire Electrical System Page 40
- 16. Cetra 8-wire Electrical System Page 40
- 17. CetraElectrical Circuit Configuration Options Page 40
- 18. Cetra 10-wire system Page 41
- 19. Interworks EQ Power and Data Statement of Line
- 20. Interworks EQ Power and Data Overview Page 209
- 21. Interworks EQ 8-Wire Power System
- 22. Interworks EQ 8-Wire Power System
- 23. Interworks EQ 8-Wire Power System
- 24. Interworks EQ Cable Management
- 25. Xsite Power and Data Statement of Line
- 26. Xsite Power and Data Overview
- 27. Xsite Base Wireway Harness and Receptacles
- 28. Xsite Jumpers
- 29. Xsite Power Entries and Power/Data Poles
- 30. Xsite Power Data Tiles
- 31. Xsite Power/ Data Tile Components
- 32. Xsite Cable Management Components
- 33. Xsite Shared Neutral 10-wire Electrical System (10S)
- 34. Xsite Shared Neutral 10-wire Electrical System (10S) Wiring Diagram
- 35. Xsite Independent Neutral 10-wire Electrical System (10D)
- 36. Xsite Independent Neutral 10-wire Electrical System (10D)
- 38. Kimball Office Resources Dealer Sales Manager Sales Specialist Customer Care/ By Design 800.482.1818 Product Technical Support 800.481.6696 Product Specifier Alibia de Vente Market Education 770.265.4006 or Alibia.devente@kimball.com
Editor's Notes
- All panels have the option of shipping powered.Jumpers only continue power.All parts are specified as needed.
- Base waireways can accommodate (18) ¼” cables at 40% file and (44) 1/4” cables at 100%.
- The first panel width mid-height power needs a jumper to go from base to mid-height with an additional distribution specified. Jumper cables will displace one receptacle at base and mid-height. On panels that are 24” and 30” wide jumper cables can connect to at the same or opposite end of an AED. Panels that are 36” wider must have the jumper installed on the same side.
- An extruded aluminum vertical power pole ships inside of the panel and attaches to the top of the panel with a top cap that is pre-cut. Any excess height telescopes into the ceiling or can be cut to size at the installation site.