Tuxedo Touch Series                          Home Automation System                                        User Guide800-0...
Table of ContentsABOUT THE SYSTEM ...........................................................................................
Table of Contents             How to Clear/Hide a Control Panel Message .....................................................
Table of Contents             Setting Daylight Savings Time .................................................................
About the SystemIntroductionCongratulations on your ownership of a Honeywell Tuxedo Touch Series Home Automation System wh...
About the System (contd)About Your Home Screen Your "Home" screen is the gateway to your System. From this screen you can:...
About the System (contd)Navigation Icon DescriptionsTo aid in the navigation of the Tuxedo Touch, a set of user-friendly i...
About the System (contd)System TroublesThe “Security” screen also displays an Icon(s) if a system trouble(s) occurs. If a ...
About the System (contd)User CodesEach user must be assigned a name with a corresponding 4-digit user code in order to gai...
SecurityIntroduction to Security System OperationYou can arm your system in one of three arming modes: Away, Stay, and Nig...
Security (contd)How to Arm the SystemArming the system in any mode is performed in the same way, as described below.Note: ...
Security (contd)How to Display FaultsThe Display Faults function is used when you see a “Not Ready Fault” message and want...
Security (contd)To bypass zones do the following:   ICON                             ACTION                               ...
Security (contd)The system may be disarmed using either of two methods. One method is employed when you enter the premises...
Security (contd)To check the status of other partitions perform the following:     ICON                           ACTION  ...
Security (contd)    b.  For Residential Systems: Press the CLEAR icon followed by your code. This acknowledges the alarm a...
Security (contd)Notes:• It is recommended that you do not use the Console Emulation Mode to enter GOTO commands. Unsatisfa...
Security (contd)How to Send Emergency MessagesAn emergency message for fire, panic, or medical can be sent to the central ...
SetupSetup allows you to make changes to the way your keypad is operating. You may access the Brightness and Volume, Displ...
Setup (contd)Adjust the Screen TimeoutsWhen the keypad is left idle, it automatically: • turns the “Backlight Off After” t...
Setup (cont’d)System InformationTo view the latest software version installed on your system, do the following:   ICON    ...
Setup (contd)Fixed IP AddressesIf the IP Address is not displayed in the lower left-hand corner on the Tuxedo Touch Keypad...
Multi-MediaThe Multi-Media feature allows you access voice messages, play video files, display a slide show of personal ph...
Multi-Media (contd)Video (Audio) SetupTo access the Video and Audio feature, do the following:   ICON                     ...
Multi-Media (cont’d)     ICON                           ACTION                                                          NO...
Multi-Media (contd)    ICON                              ACTION                                                           ...
User SetupUser Setup allows you to Add a User, Delete a User, and Edit a User. You may access User Setup from the System S...
User Setup (contd)How to Add a User   ICON                       ACTION                                                   ...
User Setup (contd)How to Edit a UserNote: You cannot edit a User’s name or number. To modify a User name or number, you mu...
User Setup (contd)Note: Use care when providing the “Yes” or “No” response. Pressing the screen outside the prescribed are...
User System SetupTime/Date SetupYou can set the time and date from the Set Time & Date screen.•   When the time is set it ...
User System Setup (contd)Setting Current Time and DateTo set the current time, do the following:    ICON                  ...
AutomationThe Tuxedo Touch Home Automation System with web hosting capability is equipped with Z-Wave technology and is de...
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Honeywell Tuxedo Touch User Guide
Upcoming SlideShare
Loading in …5
×

Honeywell Tuxedo Touch User Guide

931 views

Published on

Alarm Grid Home Security http://www.alarmgrid.com/ has provided this pdf with the permission and courtesy of Honeywell.

Alarm Grid is a home security product and alarm monitoring company that loves its customers. We have a strong appreciation of the DIY community, and want to make sure that we not only provide the best products and services out there but we also want to make sure that resources like these Honeywell product pdfs are easily accessible so that or curious customers can find what they need when they need it.

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
931
On SlideShare
0
From Embeds
0
Number of Embeds
3
Actions
Shares
0
Downloads
10
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Honeywell Tuxedo Touch User Guide

  1. 1. Tuxedo Touch Series Home Automation System User Guide800-08091 7/11 Rev. B
  2. 2. Table of ContentsABOUT THE SYSTEM ...............................................................................................................................................................................6 Introduction..........................................................................................................................................................................................6 System Interface...........................................................................................................................................................................6 Navigating through the Tuxedo Touch Keypad.............................................................................................................................6 About Your Home Screen .............................................................................................................................................................7 Multi-Media Application ................................................................................................................................................................7 Weather Forecast .........................................................................................................................................................................7 System Troubles...........................................................................................................................................................................9 User Codes.................................................................................................................................................................................10 Extended Functionality ...............................................................................................................................................................10 LED Operation ............................................................................................................................................................................10 Safe Mode ..................................................................................................................................................................................10SECURITY................................................................................................................................................................................................11 Introduction to Security System Operation ........................................................................................................................................11 How to Arm the System ..............................................................................................................................................................12 How to Arm Multiple Partitions....................................................................................................................................................12 How to Display Faults .................................................................................................................................................................13 How to Bypass Zones.................................................................................................................................................................13 How to Clear Bypassed Zones ...................................................................................................................................................14 How to Disarm the System .........................................................................................................................................................14 To disarm Multi-Partitions do the following: ................................................................................................................................15 How to Check the Status of Other Partitions ..............................................................................................................................15 Fire and Carbon Monoxide Alarm Operation ..............................................................................................................................16 In Case of Fire Alarm..................................................................................................................................................................16 Silencing and Clearing a Fire/Carbon Monoxide Alarm ..............................................................................................................16 More Choices ....................................................................................................................................................................................17 3
  3. 3. Table of Contents How to Clear/Hide a Control Panel Message .............................................................................................................................17 Advanced System Features........................................................................................................................................................17 Console Emulation Mode ...........................................................................................................................................................17 How to View the Event Log ........................................................................................................................................................18 How to Send Emergency Messages...........................................................................................................................................19SETUP......................................................................................................................................................................................................20 Brightness and Volume Control ..................................................................................................................................................20 Display & Audio Setup .......................................................................................................................................................................20 Operation Modes ........................................................................................................................................................................20 Adjust the Screen Timeouts........................................................................................................................................................21 Clean Screen ..............................................................................................................................................................................21 Routine Care ..............................................................................................................................................................................21 System Information.....................................................................................................................................................................22 IP Setup......................................................................................................................................................................................22 Web Server/Hosting ...................................................................................................................................................................23MULTI-MEDIA ..........................................................................................................................................................................................24 Voice Messages ................................................................................................................................................................................24 Video (Audio) Setup...........................................................................................................................................................................25 Picture Setup .....................................................................................................................................................................................25 Camera Setup ...................................................................................................................................................................................26USER SETUP...........................................................................................................................................................................................28 Authority Levels ..........................................................................................................................................................................28 How to Add a User .....................................................................................................................................................................29 How to Add an Existing User to a Second Keypad .....................................................................................................................29 How to Delete a User .................................................................................................................................................................29 How to Edit a User......................................................................................................................................................................30 Safe Mode ..................................................................................................................................................................................30USER SYSTEM SETUP ...........................................................................................................................................................................32 Time/Date Setup................................................................................................................................................................................32 4
  4. 4. Table of Contents Setting Daylight Savings Time ....................................................................................................................................................32 Setting Current Time and Date ...................................................................................................................................................33AUTOMATION .........................................................................................................................................................................................34 Include/Add Z-Wave Devices ............................................................................................................................................................34 Editing Z-Wave Device Names ...................................................................................................................................................36 Exclude/Delete Z-Wave Devices ................................................................................................................................................37 Exclude/Delete a Door Lock .......................................................................................................................................................37 Exclude/Delete a Honeywell Thermostat ....................................................................................................................................38 Exclude All Z-Wave Devices.......................................................................................................................................................38 Abort a Z-Wave Action ...............................................................................................................................................................38 Create a Scene...........................................................................................................................................................................39 Create a Room ...........................................................................................................................................................................41 Setting a Secondary Controller ...................................................................................................................................................41 Updating Controllers with New or Removed devices ..................................................................................................................42 Removing a Secondary Controller ..............................................................................................................................................42 Z-Wave Troubleshooting ............................................................................................................................................................42 Compatible Devices....................................................................................................................................................................43IMPORTANT NOTES ...............................................................................................................................................................................44GLOSSARY..............................................................................................................................................................................................45 NOTE: This device is a Security Enabled Z-Wave Controller. 5
  5. 5. About the SystemIntroductionCongratulations on your ownership of a Honeywell Tuxedo Touch Series Home Automation System which combines home-automation and home security. With clear, simple controls on a touch-screen interface, Tuxedo Touch is both easy to learn andeasy to use.System InterfaceEquipped with web-hosting capability and built-in Z-Wave® technology, Tuxedo Touch can be retrofitted into home electronicsdevices and systems without interference from common household wireless electronics.FeaturesThe Tuxedo Touch Keypad, used for quick and easy security system operation includes lighting and switching devices via Z-Wavecontrol of the home environment, such as; • Thermostats – temperature control for energy conservation when away from home. • Lights/Appliances - turn lights and appliances on when the security system is disarmed. • Door locks - door unlocks when the security system is disarmed. • Cameras – control and view up-to four cameras in quad view at the same time from any web enabled device.In addition, this system offers you burglary protection and may provide fire, carbon monoxide and emergency protection. To realizethe full potential of the system, it is important that you feel comfortable operating it.Your system may consist of one or more of the following: • TUXS Keypad (black/silver housing) • TUXW Keypad (white housing) • One or more other keypads for system control • Various sensors for perimeter and interior burglary protection, plus a selected number of strategically placed smoke, carbon monoxide or combustion detectors • Lighting/output devices.The system uses microcomputer technology to monitor all zones, and provides appropriate information for display on the keypadand/or other keypads used with the system. Your system may also have been programmed to automatically transmit alarm orstatus messages over the phone lines or wirelessly over GSM to a central alarm monitoring station.Navigating through the Tuxedo Touch KeypadNavigation through the Tuxedo Touch Keypad typically begins from the "Home" screen. This is the main default screen (startingscreen) and is the first screen you see when you power up and initialize the keypad. It is from this screen that you select from themain menu. Once you have made your selection, you can navigate through various sub-menus by pressing graphical icons toperform the function you desire. 6
  6. 6. About the System (contd)About Your Home Screen Your "Home" screen is the gateway to your System. From this screen you can: • control your security system • control your multi-media applications such as video, pictures and cameras • control home automation such as lighting, thermostat, and door locks Your "Home" screen is displayed most of the time and can be customized via the Multi-Media Application.Multi-Media ApplicationThe Picture/Video (Audio) features allow you to display personal photos (in a slide show format), and view video files via theexternal SD/SDHC card.It is recommended that you use the SD/SDHC card supplied with the keypad.In everyday handling, memory cards can become susceptible to malfunction and/or failure due to electrostatic discharges and theinformation on the card may be lost. In some extreme cases, the keypad may need to be reset.NOTE: Honeywell is not responsible for any loss of personal information (files, videos, photos, etc.) The background and icons shown on the “Home” screen in this manual are for example only. Your system installer may have changed the actual background and icons shown on your “Home” screen. Memory Card Insertion Insert the memory card (SD/SDHC Card) as shown. Tips for proper memory card handling: INSERT CARD • Avoid touching the contacts on the card • Quit the slide show/video application before removing the memory card. 6280-004-V0 Weather Forecast The weather forecast is displayed on the “Home” screen. To view the weather conditions for a specific location, press the Weather icon (on the “Home” screen) and select the box next to the 43 F information to be added for that location. Enter the location information on the data entry Temp. keyboard. Press the Back icon. Weather conditions for the location entered are displayed. 47 F 38 F High Low Melville, NY 7
  7. 7. About the System (contd)Navigation Icon DescriptionsTo aid in the navigation of the Tuxedo Touch, a set of user-friendly icons has been provided. The appearance and function ofthese icons are described below. ICON ICON TITLE FUNCTION ICON ICON TITLE FUNCTION Accesses Product Introduction “Product Videos” “Setup” Accesses the Setup menus. and Training Videos. Accesses the Z-Wave setup, Accesses the Message, Camera, "Automation” Scene setup, and Room setup “Multi-Media” Picture and Video features. screens. "Security” Accesses the "Security" screen. “Video” Allows user to play video files. Returns you to the "Home" Allows user to display personal “Home” “Picture” screen. photos in a slide show format. Displays Emergency functions Record and retrieve Voice “Panic” (as programmed by the installer). "Message” Messages. Note: This icon is displayed and active on all screens except while in the Clean Screen mode, during an LCD Display test in “Voice Status” Allows user to hear system status. Diagnostics and from the Video and Camera screens. Reverts to the last screen “Control Panel This icon alerts the user to a “Back” viewed. Message” Control Panel Message.Minimizing the Home Screen IconsWhen viewing wallpaper displays, the Home screen icons can be minimized by pressing the “Minimize Home” icon. Press the“Maximize Home” icon to maximize Home screen icons. Refer to Picture Setup. Minimize Setup Picture Product Maximize Security Automation Multi-Media Camera Panic Home Videos Home 8
  8. 8. About the System (contd)System TroublesThe “Security” screen also displays an Icon(s) if a system trouble(s) occurs. If a Trouble Icon is shown, contact your alarmcompany. The following Icons may be shown as applicable to your system: ICON FUNCTION AC Loss – The system is not receiving AC power. Bell Failure – The system bell or siren has a problem. Note: This Icon displays when interfacing with residential panels only. Expander Failure – The system has a failure in an expansion module. Low Battery – The system battery, that powers the system during an AC power loss, is low. LRR Supervision Failure – The Communication Device used to communicate with the central station has a supervision failure Max Attempts Exceeded – The system has exceeded the maximum attempts to communicate with the Central Station. Pager Failure – The system cannot communicate with an assigned pager. Telco-1 Cut – The system is not able to communicate with the central monitoring station over the primary phone line. Telco-2 Cut – The system is not able to communicate with the central monitoring station over the secondary phone line. Wireless Failure – The system is not able to communicate with its wireless devices.Note: If multiple faults exist, press the More Choices icon and then the Show Zones icon to view and scroll through the complete listof faults. 9
  9. 9. About the System (contd)User CodesEach user must be assigned a name with a corresponding 4-digit user code in order to gain access to authorized features andfunctions. Users for the system are programmed in a central user setup location that provides the specific questions forauthorization level, partition assignment, and RF zone assignment.Extended FunctionalityExtended functions are advanced functions that can be accessed through a standard alpha keypad or through theconsole emulation mode on your Tuxedo Touch touch-screen. Refer to your Control Panel User Guide for thesefeatures.LED OperationThe Tuxedo Touch Keypad has three LEDs as follows: SD/SDHC CARD Slot ARMED (RED) LED ON – System is armed. OFF – System is not armed. READY (GREEN) LED ON – System is disarmed and ready to arm. OFF – System is armed or disarmed but not ready. If disarmed, faults or troubles are present. MESSAGE (YELLOW) LED FLASHING – The system contains new message(s) for the User. OFF – No new messages. RESET BUTTON Press to reset keypad 6280-001-V0*Note: If the EN50131 Display feature is enabled, the "Armed" and "Ready" status LEDs turn OFF after 30 seconds and the screen returns to the Home screen until a valid user code is entered.Safe ModeThe Keypad contains a Safe Mode of operation. In the rare event that the keypad cannot successfully communicate in its graphicmode with the control panel, the Safe Mode is a backup mode that ensures that you can communicate with your system. Refer tothe Safe Mode section for further information. 10
  10. 10. SecurityIntroduction to Security System OperationYou can arm your system in one of three arming modes: Away, Stay, and Night. The following table lists the three differentarming modes and the results of each. FEATURES FOR EACH ARMING MODE Arming FUNCTION Exit Entry Perimeter Interior Mode Delay Delay Armed Armed AWAY Press to arm when no one is staying on the Yes Yes Yes Yes premises. When armed in AWAY, the system sounds an alarm if a protected door or window is opened, or if any movement is detected inside the premises. STAY Press to arm when you are staying home, Yes Yes Yes No but might expect someone to use the entrance door later. When armed in STAY, the system sounds an alarm if a protected door or window is opened, but you may otherwise move freely throughout the premises. NIGHT Press to arm when you are staying home Yes Yes and do not expect anyone to use the Yes (set for Away or Yes (set for Away or entrance door. Your installer may have Stay Mode) Maximum Mode) configured NIGHT Mode differently; have No (set for Instant or No (set for Stay or the installer describe the actual settings of Maximum Mode) Instant Mode) this mode.Important: On Commercial systems, “Away Auto Stay” mode is shown as “Away” mode (with all zones monitored).However, some interior zones may not be armed.Note: The Voice Status Icon ( ) indicates the Voice feature. Press the Voice Status Icon to hear system status.Wait 3 seconds and press again to hear Zone Faults or Trouble conditions. Voice status will annunciate even if Voicemode and Chime mode are disabled. Note that the Voice feature must be enabled (by the installer) for this icon tofunction correctly during an alarm condition.Note: There is a communicator delay of 30 seconds. This delay will prevent a report to the central station if thecontrol panel is disarmed within 30 seconds after an intrusion alarm is triggered. This delay can be removed, or itcan be increased up to 45 seconds at the option of the user by consulting with the installer. Note that emergency,carbon monoxide, and fire-type alarms are normally reported without delay. 11
  11. 11. Security (contd)How to Arm the SystemArming the system in any mode is performed in the same way, as described below.Note: Close all perimeter windows and doors before arming.Arm the system as follows: ICON ACTION NOTES 1. From the “Home” screen, press the Note: If Quick Arm is Not enabled in your system, a message to enter your SECURITY icon. User Code is received. When the system is armed for Stay, Night Stay and Instant mode, the 2. Press the selected arming icon. keypad beeps 3 times. -a text message appears stating which zones are When the system is armed for Away and Maximum mode, you will hear arming and whether or not there is an entry delay steady beeps then rapid beeping during the last 10 seconds of Exit Delay. -the screen changes to display the remaining exit delay time, and When exit delay time expires, the screen automatically changes to indicate -the exit delay time continues to count down to one. the system is "Armed".Note: For CP-01 installations, Maximum Mode cannot be used.How to Arm Multiple PartitionsNote: Some systems may not have multiple partitions and the “Arm Multi-Partitions” icon may not be displayed.To arm multiple partitions: ICON ACTION NOTES 1. From the “Home” screen, press the Security Notes: icon and then the Arm Multi-Partition icon. • A user may have access to some or all of the available partitions. 2. Select the appropriate arming mode. • If the user code is accepted, the system displays the partitions that the user has access to. 3. Enter the User Code authorized to access When exit delay time expires, the screen automatically changes to indicate other partition(s). the system is "Armed". 4. Highlight the partition from the list on the screen, and press OK. 5. Select ALL to arm all partitions listed. Note: If any zones are bypassed, a “Display Faults” ( ) icon is displayed on this screen. 12
  12. 12. Security (contd)How to Display FaultsThe Display Faults function is used when you see a “Not Ready Fault” message and want to determine where the fault is andwhat type of fault it is. To display faults do the following: ICON ACTION NOTES 1. From the "Security" screen, press the A listing of faulted and/or bypassed zones is displayed. DISPLAY FAULTS icon. As applicable, take corrective action such as closing a window or door to correct the fault. 2. If the fault cannot be corrected, you may choose to bypass a zone by pressing the zone and highlighting it and then pressing the BYPASS SELECTED icon. Show Zones Icons Distressed Zones Icons Low Clear Bypass Bypass Refresh Bypass All Faults Battery All Selected Distressed Alarm Troubles Bypasses Data Zones ZonesHow to Bypass ZonesThe Bypass function is used when you want to arm your system with one or more zones left open. Bypassed zones areunprotected and do not cause an alarm when violated while your system is armed. • Residential systems do not allow you to bypass fire, carbon monoxide or emergency zones. On commercial fire systems, a specified user may be allowed to bypass fire, carbon monoxide and system zones if the user was enabled by your system installer. • Limits apply as to how many zones can be bypassed at one time. These limits are ten zones on residential systems and five zones on commercial systems. 13
  13. 13. Security (contd)To bypass zones do the following: ICON ACTION NOTES 1. From the “Home” screen, press the Note: If any zones are bypassed or faulted, a Display Faults icon is also SECURITY icon. displayed on this screen. 2. Press the MORE CHOICES icon. 3. Press the SHOW ZONES icon. While the keypad is requesting and receiving the zone data from the control panel, the screen displays "Please Wait!". Then the zones, along with their current status, are displayed. 4. Highlight the zone(s) to be bypassed and Note: If zones have already been bypassed, the top of this screen indicates press the BYPASS SELECTED icon. “Ready Bypass”. 5. Enter your 4-digit user code. The screen is displayed with the instructions "To Bypass Zones, Enter Code". 6. Press the BACK icon to return to the The "More Choices" screen is displayed showing the system status as Ready- “Arming” screen. Bypass.How to Clear Bypassed ZonesA bypassed zone is automatically unbypassed when you disarm the system. If a zone is bypassed, you can remove the bypass asfollows: SCREEN ACTION NOTES 1. Press the SHOW ZONES icon. While the keypad is requesting and receiving the zone data from the control panel, the screen displays "Please Wait!". Then the zones, along with their current status, are displayed. 2. Press the CLEAR BYPASSES icon. Note: If the system is armed and you unbypass a zone, it disarms the system. If zones are still faulted (not ready) the system will indicate the 3. Enter your 4-digit user code. The "More status as “Not Ready Fault”. Choices" screen is displayed showing the system as Ready to Arm.How to Disarm the SystemIMPORTANT: If you return to your home or business and the main burglary sounder is on, DO NOT enter the premises, but callthe police from a nearby safe location. If you return to your home or business after an alarm has occurred and the main sounderhas shut itself off, the keypad beeps rapidly upon entering, indicating that an alarm has occurred during your absence. LEAVEIMMEDIATELY and CONTACT THE POLICE from a nearby safe location. 14
  14. 14. Security (contd)The system may be disarmed using either of two methods. One method is employed when you enter the premises and the other iswhen you have been in the premises with the system armed (i.e., Stay and Night arming modes).To disarm the system when entering the premises:The keypad automatically displays the Entry Delay Active screen when you enter the premises: ICON ACTION NOTES 1. Enter your 4-digit user code. The partition is disarmed and the "Arming" screen is displayed showing the system as Ready to Arm. Note: If you have a commercial system and a time window has been defined for when you may disarm the system, the system does not disarm if you are outside that time window.To disarm the system when already in the premises: ICON ACTION NOTES 1. Press the Disarm icon. 2. Enter your 4-digit user code.To disarm Multi-Partitions do the following: ICON ACTION NOTES 1. From the “Home” screen, press the The keypad displays “Multi-Partition Arming”. Security icon. 2. Press the Arm Multi-Partition icon. 3. Press the Disarm icon. 4. Enter your 4-digit user code. 5. Highlight the partition(s) to disarm and press OK, or press ALL to disarm all partitions.How to Check the Status of Other PartitionsThis system supports between one and eight Partitions (depending on the system.) Partitioning enables a single physical alarmsystem to control up to eight areas of protection (partitions) depending on the system you have purchased. Each Touch-Screenkeypad is assigned a default partition for display purposes, and shows only that partitions information.Note: A letter “H” following the partition name or number indicates that this is the default partition for the keypad.For example, if your physical site is a four-apartment housing unit, your alarm system may be configured with four partitions.Each apartment’s zones (door, windows, smoke detectors, etc.) are assigned to separate partitions, giving each apartmentindependent arming/disarming control of its own partition (area). A landlord or manager may be granted access to all partitions,so he/she can control the entire system.If a user is so authorized, a keypad or other keypad in one partition can be used to perform system functions in another partition.(Note that only those partitions authorized and programmed by the installer can be accessed in this manner.) 15
  15. 15. Security (contd)To check the status of other partitions perform the following: ICON ACTION NOTES 1. Press the SECURITY icon. This screen displays the available partitions and their current status. 2. Press the "Current Partition" icon (lower The current partition is shown at the top of the display (P1). To change this edge of the screen; in this case it displays assignment, select the appropriate icon (e.g., press P2 to switch control to P1 H unless changed by installer). Partition 2). Note: After leaving this screen when using a residential panel, the selected 3. Enter the code authorized to access other partition in the keypad automatically reverts back to the keypad’s home partition(s). partition after two minutes. When using commercial panels, you must select If the code is accepted, the system displays the the keypad’s home partition to return to it. partitions that user has access to. Note: A code may have access to some or all of the available partitions.Fire and Carbon Monoxide Alarm OperationYour fire alarm system and carbon monoxide detector (if installed) is on 24 hours a day, providing continuous protection. In theevent of an emergency, the installed smoke, heat, carbon monoxide detectors automatically send signals to yourControl/Communicator, triggering a loud interrupted sound from the keypad. An interrupted sound is also produced by optionalexterior sounders. EVACUATE ALL OCCUPANTS FROM THE PREMISES IMMEDIATELY. Notify your CentralStation/Security Company immediately and wait for further instructions. UL CO annunciation has not been investigated by UL and may not be used for UL installations.In Case of Fire Alarm1. A FIRE message appears at your keypad and remains on until you silence the alarm.2. Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest keypad and manually initiate an alarm by pressing the panic key assigned as FIRE emergency (if programmed by the installer) and hold down for at least 2 seconds.3. Evacuate all occupants from the premises.4. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately.Silencing and Clearing a Fire/Carbon Monoxide Alarm1. Silence, acknowledge, and clear the alarm by: a. For Residential Systems: Press “Touch here to Silence” on the display to silence the alarm. For Commercial Systems: Enter your code. This silences and acknowledges the alarm and disarming of the system (if armed). 16
  16. 16. Security (contd) b. For Residential Systems: Press the CLEAR icon followed by your code. This acknowledges the alarm and the disarming of the system (if armed). For Commercial Systems: Press the CLEAR icon followed by your code. The system attempts to clear the alarm from memory. If NOT successful (i.e., smoke in the detector) the Security screen is displayed and the Display Faults icon displays a “Not Ready Fault”. c. Press the DISPLAY FAULTS icon on the Arming screen. The faulted fire/carbon monoxide zone is displayed. d. Press the CLEAR icon and then enter your code. This clears the Fire Alarm/CO Alarm from the system.2. If the keypad does not indicate a READY condition after the second sequence, press the DISPLAY FAULTS key on the Arming screen to display the zone(s) that are faulted. Be sure to check that smoke detectors/carbon monoxide detectors are not responding to smoke, heat, or gas producing objects in their vicinity. In this case, eliminate the source of heat, smoke or leak.3. If this does not remedy the problem, there may still be smoke/gas in the detector. Clear it by fanning the detector for about 30 seconds.4. When the problem has been corrected, clear the display by entering the DISPLAY FAULTS icon on the Arming screen, selecting the fire or carbon monoxide zone, pressing the CLEAR icon and then entering your user code.Note: Contact your Central Station/Security Company for servicing if you have further problems with your system.More ChoicesHow to Clear/Hide a Control Panel MessageThe Control Panel Message icon alerts the user to a control panel message. When a Control Panel Message is displayed, the userhas two options. User can clear the Control Panel Message immediately, or minimize the window and clear it at a later time.To Clear/Hide the Control Panel Message, do the following: ICON ACTION NOTES 1. To clear; press CLEAR. Once your Authorized Code is accepted, the Control Panel Message is 2. Enter your Authorized Code or, cleared. If the alarm is still present, press CLEAR again and then enter your 3. To hide; press HIDE to clear the Authorized Code again. Control Panel Message later. Press the HIDE icon to address the condition later.Advanced System FeaturesWhile most of the commonly used security functions are available from the keypad’s advanced user interface, there are some lessused, advanced features that can either be accessed through Console Emulation mode on the keypad or a standard alpha keypad.To use features not supported by the keypad, refer to your Control Panel User Guide.Console Emulation ModeConsole Emulation Mode allows you to use a keypad interface just as you would a regular system keypad. All commands shownin Console Emulation mode can also be executed from a standard alpha keypad. 17
  17. 17. Security (contd)Notes:• It is recommended that you do not use the Console Emulation Mode to enter GOTO commands. Unsatisfactory operation may result from issuing GOTO commands in Console Emulation.• Two icon panics (1 & *, 3 & #, and * & #) do not function in the Console Emulation Mode. The A, B, C, and D icons do function if programmed as panic keys. Check with your system installer for details.• Commercial systems with Alpha keypads have a feature where if you press a key for 5 seconds, you receive self help messages about the pressed key or holding the * key for 5 seconds to provide zone descriptors. These features do not function in the keypad as all key presses are instantaneous.How to Enter Console Emulation ModeTo access Console Emulation Mode, do the following: ICON ACTION NOTES 1. From the Home screen, press the SECURITY icon. 2. Press the MORE CHOICES icon. 3. Press the CONSOLE MODE icon. Perform functions as you would from a standard alpha keypad.How to View the Event LogYour system has the ability to record various events in a history log wherein each event is recorded with the time and date of itsoccurrence. The control panel must be programmed to record various system events in the installer programming mode.To view the Event Log, perform the following: ICON ACTION NOTES 1. From the “Home” screen, press Security Note: While keypad is requesting and receiving the event log data from the and then the MORE CHOICES icon. control panel, the "Event Log" screen displays "Please Wait!" The Next>> and <<Previous icons are shown for commercial panels only 2. Press the EVENT LOGS icon. when 100 or more events are in the log. They are not shown for residential The first ten events are displayed. panels. 3. Press the SHOW MORE button to view all When All Partitions or All Events icon is pressed, and more than 100 items, and press the up/down arrows to scroll events exist, the Next>> and <<Previous icons are displayed showing the next 100 or previous 100 events. through the event log. 18
  18. 18. Security (contd)How to Send Emergency MessagesAn emergency message for fire, panic, or medical can be sent to the central monitoring station from the Emergency screen. TheEmergency screen can be accessed by activating the "PANIC" Icon located on the lower right corner of the screen.Perform the following to send an emergency message. ICON ACTION NOTES 1. Press the PANIC Icon. You are immediately returned to the screen from which you pressed the 2. Press and hold (for at least 2 seconds) the “PANIC” Icon. NOTE: The Emergency screen cannot be accessed while running a associated alarm icon (FIRE, PANIC, SILENT screen diagnostic test or while in the clean screen mode. PANIC or MEDICAL). Emergency Icons • Emergency messages are optional and may not be available on your system. Ask your system installer if emergency messages are available on your system. Fire Panic Silent Panic MedicalUL Medical functionality has not been evaluated by UL and may not be used in UL Listed applications. 19
  19. 19. SetupSetup allows you to make changes to the way your keypad is operating. You may access the Brightness and Volume, Display& Audio Setup, and System Setup from the "Setup" screen.Brightness and Volume ControlFrom the "Home" screen, access the "Setup" screen as follows: ICON ACTION NOTES 1. Press the Setup icon. If changes are made, when you exit a Settings Changed! pop-up window 2. Move the Brightness/Volume slide bar up or is displayed asking “Remember New Settings?“ Yes saves the change. down to increase or decrease settings. No discards the change.Display & Audio SetupYou may access Operation Modes, Backlight Off After time, To Homepage After time, Auto Slideshow After time andClean Screen from Display & Audio Setup.Operation ModesOperation modes provides access to Chime Mode, Voice Mode, and Voice Chime which allows you to turn the keypad chimemode and voice mode on or off.• Chime Mode – Keypad chimes whenever a door or window is open.• Voice Mode – Keypad voice annunciates whenever a change in system status occurs.• Voice Chime – The chime mode and voice mode are in effect with the chime beeps followed by voice annunciation.Access the "Operation Modes" screen as follows: ICON ACTION NOTES 1. From the “Setup” screen, press the Disp & If the Chime Mode and Voice Mode are both selected, the Voice Chime is Audio Setup icon. automatically selected. 2. Enter your “Authorized Code", if required. 3. Select Chime Mode or Voice Mode to turn It may take a few seconds for the Chime Mode to take effect. the mode on or off. When the keypad exits the “Operation Modes” screen, your selection is 4. Press the HOME or BACK icon after making saved. your selection. 20
  20. 20. Setup (contd)Adjust the Screen TimeoutsWhen the keypad is left idle, it automatically: • turns the “Backlight Off After” the selected backlight off time has expired (unless “Never” option is selected). • returns to the “Home” screen after the selected “To Homepage After” time has expired (unless “Never” option is selected), and • if enabled, the “Auto Slideshow After” time begins the slide show.To select the desired screen timeouts, do the following: ICON ACTION NOTES 1. From the "Home" screen, press the Setup If changes are made, when you exit a Settings Changed! pop-up window is icon. displayed asking “Remember New Settings?“ 2. Press the Disp & Audio Setup icon. Settings include: • Backlight Off After X time 3. Enter your “Authorized Code", if required. • Return To Homepage After X time 4. Press the desired selection from the drop- • Auto Slideshow After X time. down list displaying the time period for each Note 1: The “To Homepage After” option is only available if the EN50131 option. display option is not enabled by the installer. Yes saves the change. Note 2: When in EN50131 mode, “Auto Slideshow After” is preset to “1” No discards the change. minute and can not be changed.Clean ScreenWith the exception of normal cleaning, the keypad is maintenance free. Clean the touch-screen as follows: ICON ACTION NOTES 1. From the “Home” screen, press the Setup At the "Touch Screen Disabled for =30 Seconds" screen, the touch- icon. screen should be wiped clean of fingerprints using a mild soap solution and a soft cloth. When the counter reaches zero, the window automatically closes 2. Press the Disp & Audio Setup icon. and the touch-screen is active. 3. Enter your “Authorized Code", if required. NOTE: The Emergency screen cannot be accessed while running in the 4. Press the CLEAN SCREEN icon to disable clean screen mode. the keypad for 30 seconds so you can wipe the A pop-up window displays "Touch Screen will be disabled so that screen clean. you may wipe the screen clean. Please use a damp, soft cloth. DO NOT 5. Press Continue to disable the touch-screen. use any liquids, sprays, or ammonia-based cleansers. Press CONTINUE to disable touchscreen." 6. Press Cancel to exit. **Panics cannot be initiated during this process**IMPORTANT: Do not use an abrasive cleaning agent or abrasive cloth when cleaning the touch-screen or damage to the touch-screen may occur.Routine Care• Treat the components of your security system as you would any other electrical equipment. Do not slam sensor-protected doors or windows.• Keep dust from accumulating on the keypad and all protective sensors, particularly on motion sensors and smoke detectors.• The keypad case and sensors should be carefully dusted with a dry soft cloth. Do not spray water or any other fluid on the units. 21
  21. 21. Setup (cont’d)System InformationTo view the latest software version installed on your system, do the following: ICON ACTION NOTES 1. From the “Setup” screen, press the System The Software Version is displayed on the lower right of screen. Setup and then the Advanced Setup icons. 2. Enter your authorized code.IP SetupFollow the steps below to control your local Z-Wave devices via your PC, Smart Phone or Tablet.Automatic IP AddressesIn most cases, IP addresses are assigned automatically by your Internet Service Provider. The IP Address is displayed in thelower left-hand corner on the Tuxedo Touch Keypad “Home” screen. To access “IP Setup”, do the following: ICON ACTION NOTES 1. At the Tuxedo Touch keypad: Take note of the address; you will need to enter this address into your a) Press the Setup icon from the “Home” browser. screen. b) Press the IP Setup icon; the “IP Setup” screen displays the IP Address and Default Gateway Address of your router. c) Press the Refresh button; the IP information will automatically update. This may take up to 60 seconds. 2. Press Apply; the keypad will save the information and reset. 3. After proper setup, the IP Address will be displayed on the “Home” page. To set up a User Account: Note: Account Setup allows you to add up to 5 users. 1. Press the Account Setup button. Use the Data Entry Keyboard to enter the required information. 2. Highlight a row on the screen and enter a • Use the Shift key for capital letters user name on the “Data Entry Keyboard”; • Use the BS (Backspace) key to make corrections. press OK. • Press OK 3. Highlight the same row on the screen and enter a user password; press OK. A pop-up window displays the message: Save the Change ? 4. Press the Save icon. The new user is Select Yes to save the settings. displayed on the screen. Select No to cancel. 5. Press Apply. 6. To delete a user, highlight the User Name and press the Delete button. 22
  22. 22. Setup (contd)Fixed IP AddressesIf the IP Address is not displayed in the lower left-hand corner on the Tuxedo Touch Keypad “Home” screen, you may require afixed IP Address. Obtain the IP Address by contacting your Internet Service Provider and then do the following: ICON ACTION NOTES 1. At the Tuxedo Touch Keypad: a) Press the Setup icon and then press the Use the Data Entry Keyboard to enter the required information. • Use the Shift key for capital letters IP Setup icon; the “IP Setup” screen. • Use the BS (Backspace) key to make corrections. b) Press the button next to Obtain an IP • Press OK address automatically to de-select it. c) Enter the “IP Address” by pressing the first set of 3 zeros (“000”) on the screen, and enter the first three numbers of the IP address on A pop-up window displays the message: the “Data Entry Keyboard”. Repeat this step Settings Changed! Remember new settings? until the complete address has been entered Select Yes to save the settings. and press Apply. Select No to cancel. 2. At your PC, Smart Phone or Tablet Browser: a) Start your browser and enter your IP Address.Web Server/HostingThe Tuxedo Touch keypad offers web-hosting capability allowing you to access your Security and Home Automation System viaany web enabled device. The Tuxedo Touch keypad’s IP Address is displayed on the “IP Setup” screen as well as the “Home”screen. This IP Address is used on standard web browser to control user functions such as, Security, Z-Wave operation andcamera viewing. Web Server/Hosting is not Listed for use in UL installations. Remote arming/disarming/programming is not to be used in ULUL Listed Installations.From your web enabled device, do the following: ACTION NOTES 1. At your PC, Smart Phone or Tablet : • If using a Smart Phone or Tablet browser, access to basic arming a) Navigate to the Settings feature. commands are available. b) Turn ON the “Wi-Fi” setting and select the router to • If using a PC, full access to keypad options are available. connect to. Enter a name and password, if required. IMPORTANT: Use the web browser to view cameras for non-security c) Open the browser and enter the IP Address displayed on purpose only. Camera streams viewed from the web browser can stop the keypad into your browser. You can now control your without indication due to network connection issues. Security System, local Z-Wave devices and view your local cameras from your browser. 23
  23. 23. Multi-MediaThe Multi-Media feature allows you access voice messages, play video files, display a slide show of personal photos, and view up-to four cameras at once from your keypad. UL Multi-Media functionality is supplementary only and has not been evaluated by UL.Voice MessagesThe Tuxedo Touch Keypad can record voice messages for others on the premises. The number of messages is not limited;however, the total time of all messages added together cannot exceed 120 seconds. Note: The voice messages are stored in thememory and all messages are lost if the keypad loses power or if it is reset.Recording/Retrieving MessagesVoice messages are recorded and retrieved using the “Message Center” screen. To access messages, do the following: ICON ACTION NOTES 1. From the Home screen, press Multi-Media then press the Message icon. 2. Press the Record icon and record your As you are recording your message, the remaining time counter counts down message while staying within approximately to indicate the total remaining time available and a “Recording New Memo…” message is displayed above the message list window. one foot of the keypad and speaking at a normal voice volume. 3. Press the Stop icon when you are done The message indicator flashes and the message is listed in the message list recording the message. window. To record additional messages, repeat steps 2 and 3. To exit, press the BACK or HOME icon. To retrieve a voice message; As the message is being played, a “Play (x): Voice Memo…” message is 4. Select from the message list and then displayed above the message list window. press the Play Message icon. Use the Pause When the end of the message is reached, the playback stops. Note: The Message LED will continue to flash until all new messages have button to pause the playback, if desired. been played back entirely. 5. To listen to the next message, press the The “Delete Memo” screen is displayed. Advance One Message and Play icon. You can press the Delete Selected button to delete only the currently 6. If you wish to delete messages, press the selected message, the Delete All button to delete all or the Cancel button to return to the “Message Center” screen without deleting any messages. Cancel icon. Note: At any time you may highlight a message you want to listen to and 7. To exit, press the HOME icon. press the Play Message icon. Message Icons Use the Pause, Next, and Previous icons to navigate through the list of messages. Pause Next Previous 24
  24. 24. Multi-Media (contd)Video (Audio) SetupTo access the Video and Audio feature, do the following: ICON ACTION NOTES 1. Insert your personal media (SD/SDHC) A Video Converter is required to convert videos for proper playback on the card (with stored video files) first. Tuxedo Touch Keypad. Use an Internet search engine to locate and 2. Press the Multi-Media icon and then press download a Video Converter, then follow the steps in the Video Converter Instructions (provided in the carton). the Video icon. 3. Highlight a video file from the list and NOTES: press the Play icon to start the selected video. • Maximum video resolution should not exceed 400 x 240. 4. Press the Repeat icon to continually • If the video file causes the keypad to lock, use a small object (such as a paper clip) to press the reset button located in the lower right-hand side replay the selected video. of the keypad to reset the keypad. 5. Deselect the Repeat icon to automatically • Videos can not be played when the EN50131 Display is turned ON. play the complete list of video files starting with the first video and ending with the last. Use the slide bar to scroll through the video list. If desired, press the Full View icon to view video in full screen. Video Icons Press the appropriate icon to Play, Pause, view a Full View or Repeat the video. Play Pause Full View RepeatPicture SetupThe Picture feature allows the user to display up to 1000 personal photos on the keypad and can be accessed by pressing thePicture icon on the Home screen, or access this feature as follows: ICON ACTION NOTES 1. Insert your personal media (SD/SDHC) Photo files can be viewed from the (SD/SDHC) Card. Formats supported card (with stored files) first. are .bmp or .jpg files. 2. Press the Multi-Media icon, and then NOTES: press the Picture icon. • To exit slide show at any time and resume keypad operation, press anywhere on the screen. 3. Select the type of viewing transition • The first image is displayed and a list of stored images appears on desired by pressing the Transition arrow. the screen. Select from (Standard, Horizontal, Vertical • When an image is loading, no other Picture Setup functions can be or Fade Out). performed (play, previous, next, add or set wallpaper). 25
  25. 25. Multi-Media (cont’d) ICON ACTION NOTES 4. Press the Slide Delay arrow to select the Press the TOP button to move up one level in the directory. time interval that you want to allow Press the OPEN button to view larger images and/or open directories, between each photo being viewed. Choose select from the list of stored images. from (5, 10, 15, or 20 seconds). Press the CLEAR ALL button to clear all pictures from the current slide To set a picture as wallpaper: show rotation. 1. Use the slide bar to scroll through the list of pictures and highlight the file you want to be displayed on the keypad screen. NOTE: When viewing wallpaper displays, the Home screen icons can be 2. Press the Set Wallpaper icon; view your minimized by pressing the “Minimize Home” icon. Press the “Maximize selection from the “Home” screen. Home” icon to maximize the Home screen icons. Picture Icons Previous Image Next Image Add Image Minimize Home Maximize Home Play ImageCamera SetupThe Camera feature allows you to view up-to four cameras at one time. Cameras should be in their final location and turned onbefore they are added to the system. To set up a camera, do the following: ICON ACTION NOTES 1. Connect an RJ45 cable to the back of the Notes: Tuxedo Touch Keypad and connect the 1. QuickTime® media player must be installed on your PC. opposite end to your Ethernet on your 2. Camera resolution should be 5 fps (5 frames per second) or lower. existing “powered-up” router. 3. Camera viewing is not compatible if using Opera web browser. 2. Connect an RJ45 cable to the back of your IMPORTANT: Use the web browser to view cameras for non-security camera (LAN) and connect the opposite purposes only. Camera streams viewed from the web browser can stop end to the Ethernet on your router. without indication due to network connection issues. Initial camera setup cannot be performed over a wireless connection. 3. Apply power to the Camera. It may take a Use the Data Entry Keyboard to enter the required information. few seconds for initial power-up of camera. • Use the Shift key for capital letters • Use the BS (Backspace) key to make corrections. • Press OK 26
  26. 26. Multi-Media (contd) ICON ACTION NOTES 4. Press the Multi-Media and Camera icons or press the Camera icon from the “Home” screen and then press the Camera Setup icon. The “Camera List” screen is displayed. Press the Clear icon to clear the camera list. 5. Press the Scan icon to locate the camera. Once located, highlight the camera address, and press the Edit icon and go to Step 7 below. 6. If the camera information is not automatically obtained, press the Add icon to manually enter Enter the appropriate information (Name, User, RTSP Path, Resolution, information on the “Add Camera” screen. Frame Rate, Address, Password, RTSP Port, HTTP Port) if known. a) To retrieve camera settings and connect to Enter the appropriate wireless information SSID, Network Type, Channel No., Security System and Shared Key, if applicable. the camera, press the Camera Settings icon. Security System information for WEP enter Authentication Type, WEP b) Press the Reset icon to reset the camera to Encryption, Pass Phrase, and WEP Key. factory default. Select Yes or Cancel. For WPA PSK TKIP, WPA PSK, AES, and WPA2 PSK AES, enter the Shared Key using the Data Entry keyboard and press OK. 7. To edit camera information, highlight the A pop-up window displays “cam (name) wireless set OK”, if successful. camera and press the Edit icon; the “Camera Or, “cam (name) wireless set Failed”. Configuration” screen is displayed. 8. When all cameras have been added, press the Wireless Settings icon and on the “Wireless The RJ45 cable can now be removed for the wireless cameras and once Settings” screen enter the wireless information power has been recycled to the camera you can view wirelessly via the from your router. Tuxedo Touch Keypad. 9. Press Apply to All to set cameras to wireless If camera does not have wireless capability, leave it connected to router. operation. Setup Icons Camera Icons Clear Play Scan Add Delete Clear Edit Refresh Stop Auto Pan Quad View Full View Pan/Tilt BackNote: To use the Pan/Tilt feature in Quad View, select the camera name from the camera list and then press Pan/Tilt. UL Camera functionality is supplementary only and has not been evaluated by UL. 27
  27. 27. User SetupUser Setup allows you to Add a User, Delete a User, and Edit a User. You may access User Setup from the System Setupscreen. Each user must be assigned a name with a corresponding 4-digit user code in order to gain access to various features andfunctions. The keypad can hold the identity for 10 Users in its memory. If additional Users are needed, define the additionalUsers using the Console Emulation Mode.Users for the system are programmed in a central user setup location that provides the specific questions for authorization levelsassigned to different users. You may want these users to be the same, but there are situations in which you may want a user tohave limited capabilities. These capabilities are defined by the Authority Level assigned each user.Authority LevelsAuthority levels define the system functions a particular user can perform. Depending on the authority assigned to you, there arecertain system functions you may be prohibited from performing. The following information describes the authority levels thatcan be assigned through the keypad and provides the equivalent authority level name found in your alarm system manuals. Theauthority levels that can be assigned are as follows: Equivalent System Name Authority Functions Residential Commercial Level Systems Systems Master Can perform all security functions, add/delete users in assigned partition, Partition Master Level 1 Master program scheduled events, and change partition master code Normal Perform security functions (arm, disarm) Standard User Level 3 Operator A Guest Can arm the system in assigned partitions, but cannot disarm the system Guest Level 4 Operator B unless the system was armed with this code. Note: Do not assign this level if Quick Arm is enabled in your system. No Used to restrict access from a partition. N/A N/A Access 28
  28. 28. User Setup (contd)How to Add a User ICON ACTION NOTES 1. From the "Home" screen, press the On the Data Entry screen, enter the user information. Setup icon. • Use the Shift key for capital letters • Use the BS (Backspace) key to make corrections. 2. Press the System Setup icon. • The @#$ key is not available for use at this time. These characters cannot 3. Press the USER SETUP icon. be saved to the control panel. 4. Press the ADD USER icon and enter The authorized code for adding users is dependent upon the alarm panel you your Authorized Code. are interfacing with. Check your alarm panel Installation and Setup Guide to determine who can add users. 5. Press the box next to Enter User Name. If assigning this user to wireless key, enter one of the zone numbers of the 6. Type in the user name (6 characters keyfob (the wireless key must be programmed first before it can be assigned to max.; no spaces between characters) and a user). press the OK icon. Select the partitions, access level, and enter an available user number for this user. 7. Press the box next to User Number and Available user numbers: enter an “available” (3-digit) user number; For Residential enter a number from 002-049. press the OK icon. For Commercial enter a number from 002-250. 8. Press the box next to Enter User Code, enter the 4-digit User Code for this user and press the OK icon. 9. Press the box next to RF Button Zone (if used); enter the 3-digit RF Button Zone for this user. 10. Press the Save icon.How to Add an Existing User to a Second KeypadAfter adding a user to the first keypad, the same user can be added to a second keypad. From the second keypad goto “User Setup” and enter the same user name and same user code (refer to “How to Add a User” above). The secondkeypad will automatically update the user information. Press Save.How to Delete a User ICON ACTION NOTES 1. Select the User you want to delete. Three selections are available: add a user, edit a user, or delete a user. 2. Press the DELETE USER icon. The authorized code for deleting, adding, and editing users is dependent upon 3. Enter your Authorized code. the alarm panel you are interfacing with. Check your alarm panel Installation 4. Press the appropriate icon. and Setup Guide to determine who can delete, add, and edit users. The Confirm Delete screen is displayed. 29
  29. 29. User Setup (contd)How to Edit a UserNote: You cannot edit a User’s name or number. To modify a User name or number, you must delete the User and re-enter User.Edit a user as follows: ICON ACTION NOTES 1. Press the EDIT USER icon. Three selections are available: add a user, edit a user, or delete a user. 2. Enter your Authorized code. When you select Save, the configuration changes are saved and you are returned to the User Setup screen. 3. Select the options needed for this user Note: The authorized code for deleting, adding, and editing users is and press the Save icon. dependent upon the alarm panel you are interfacing with. Check your alarm panel Installation and Setup Guide to determine who can delete, add, and edit users.Safe ModeThe Safe Mode may be automatically entered by the program on a communication failure or may be entered manually oncommand.To Exit the Safe Mode:1. Press the ! SAFE MODE ! bar.2. Select “Yes” to return to the Normal Mode of operation. The keypad resets and normal operation returns as long as the originalconditions that caused the entry into Safe Mode do not still exist. ICON ACTION NOTES ! SAFE MODE ! 1. Select Safe Mode and then press Apply. While in the Safe Mode, the Home screen displays the Security, Panic, and Message Icons. A message !SAFE MODE! is displayed at the lower left 2. Press the OK icon. side of the screen. 3. To exit, press the safe mode bar and press The keypad resets and restarts in the Safe Mode. Yes to return to Normal Mode.In the rare event that the keypad cannot successfully communicate in its graphic mode with the control panel, the Safe Mode is abackup mode that ensures that you can communicate with your system.In this mode, the keypad operates much like a standard non-graphic keypad so that you can control your system until theproblem is corrected.If this situation occurs, the keypad presents you with a message of “Problems detected. Start Keypad in Safe Mode?” and requestsa “Yes” or “No” response. If you answer with “Yes”, the keypad enters into the Safe Mode. If you answer with “No”, the keypadtries to communicate with the panel again. After 3 consecutive times of receiving no response, the keypad enters the Safe Modeautomatically. 30
  30. 30. User Setup (contd)Note: Use care when providing the “Yes” or “No” response. Pressing the screen outside the prescribed area may cause thebackground to come to the front. If this occurs, the Yes/No message that disappeared times-out in 30 seconds even though it isnot visible. Then the keypad resets into the Normal Mode (or Safe Mode if this is the third time that the warning messageappeared).Note that this is a limited mode of operation. While in this mode:• You can use the Security icon to access the Console Emulation Mode of operation to try to clear your faults, disarm the system, or enter additional Alpha Keypad commands specified in your panel User Guide. You can perform almost all functions that you can perform from a standard non-graphic alpha keypad.• You can press the “Panic” key and generate Emergency Messages as defined in the panels home partition for this keypad.• The Armed and Ready LEDs on the front of the keypad indicates the keypad’s home partition status. The Message LED (on models with Voice feature) or Trouble LED (on models without Voice feature) is not active in the Safe Mode.• The Chime mode functions in the Safe Mode.• When an alarm occurs in the Safe Mode, it is displayed on the Console mode screen only and is not shown on the Home screen.• Z-Wave Scenes do not function in Safe Mode. 31
  31. 31. User System SetupTime/Date SetupYou can set the time and date from the Set Time & Date screen.• When the time is set it is stored in the keypad and sent to the control panel when you press the Apply icon and answer Yes to the following prompt. Additionally, when using the keypad with a residential panel, the panel downloads its time into the keypad once an hour after the clock is set.• If Get Time is pressed, the keypad downloads the time and date from the control panel and exits the Set Time & Date screen.Note: This icon ( ) appears with residential panels and may not appear with all commercial panels.Setting Daylight Savings TimeTo set the daylight savings time do the following: ICON ACTION NOTES 1. Press the Time/Date Setup icon; enter If DST On is selected, the keypad adjusts for Daylight Savings time at the your Authorized Code. month, week and time chosen. 2. Press the DST icon if you want daylight savings time to affect your system clock. 3. Set the “Start DST” time and then the “End DST” time by pressing the Month, Weekend and Hour that you want DST to start. 4. APPLY saves the settings. Make sure "DST On” is checked to enable this feature. 32
  32. 32. User System Setup (contd)Setting Current Time and DateTo set the current time, do the following: ICON ACTION NOTES 1. Press the Time/Date Setup icon; enter After each selection the window closes automatically and the selection is your Authorized Code. displayed. 2. Press the Month "arrow", and select the Select if you want a 12-hour or 24-hour format for your time display by pressing the circle to the left of the 12 Hour display. current month. 3. Press the Year that is being displayed and enter the current year. 4. Press the Hour that is being displayed and enter the current hour. 5. Press the Minutes that is being displayed and enter the current minute. 6. Press AM or PM. (Each depression switches the AM/PM display). 7. Press the MMDDYY “arrow”, and select a format for which you want the year to be displayed. 8. Press the Get Time icon to have the keypad download the time and date from the control panel and exit the Set Time & Date screen. 9. Press Apply. Yes saves the time changes in your A confirmation screen is displayed. security system. Note: A Yes response is recommended. No saves the changes to the keypad only. 33
  33. 33. AutomationThe Tuxedo Touch Home Automation System with web hosting capability is equipped with Z-Wave technology and is designed toautomate devices in a home control network. The keypad allows you to easily add and control multiple devices with the press of abutton. This section describes how to Include (add) devices into your home control network.NOTE: Z-Wave applications have not been evaluated by UL.UL Automation functionality is supplementary only and has not been evaluated by UL.Include/Add Z-Wave DevicesDevices should be in their final location prior to inclusion.WARNING: Automation is intended for lifestyle convenience. Do not use automation for life safety and property protection.Include a Light, Switch or Outlet Module Install a Z-Wave Light, Switch or Outlet module as described below. ICON ACTION NOTES 1. At the Tuxedo Touch Keypad: Note: Z-Wave light modules may vary; follow the instructions in the a) Press the Automation icon from the Users Guide for your specific device to include properly into the Z-Wave network. “Home” screen and then press the Z-Wave Setup icon to display “Z-Wave • If a dimmer module was included, an On/Off button and a slide bar (to control dimmer) are displayed. Device Management” screen. b) Press the Z-Wave Include/ Add icon. • If an on/off light/appliance module was included, an On/Off button (to control the device) is displayed. The keypad displays a series of messages: 2. At the device Module: a) Press the Function Key on the device. “Start add device. Please press function key on device” “Adding Controller Unit” “Adding Slave Unit” “Device added successfully” Z-Wave Device Management Icons Include/Add Exclude/Delete Abort Remove Failed Edit Reset Default Link Router Security 34

×