Mobi dock getting started

354 views

Published on

Please note: The new Mobi 360 and Mobiview come with their own charging station. The Mobi Dock does work with the Mobi Learner.

You can find a data sheet on the Mobi Learner here :

http://www.slideshare.net/WKMcIntosh/mobi-learner

Also, to be clear any Mobi (Mobi KWIK, Mobi Learner, Mobiview or Mobi 360) can be charged individually . The Idea of the Mobi Dock was to have these student devices "ready to go" without plugging in three at a time.

I am the authorized K-12 representative in South Carolina for eInstruction by Turning Technologies

Bill McIntosh
SchoolVision Inc..
Authorized South Carolina K-12 Consultant for eInstruction by Turning Technologies
Phone :843-442-8888
Email :WKMcIntosh@Comcast.net
Twitter:@OtisTMcIntosh

SchoolVision Website on Facebook: https://www.facebook.com/WKMIII

Website : www.einstruction.com
Stay Connected - @eInstruction • Facebook



Turning Technologies | 255 West Federal Street | Youngstown, OH Main: 330-746-3015 | Toll Free: 866-746-3015 | Fax: 330-884-6065
www.TurningTechnologies.com

Published in: Education
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
354
On SlideShare
0
From Embeds
0
Number of Embeds
6
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Mobi dock getting started

  1. 1. 1 Using Your Interwrite Mobi Dock™ The Interwrite Mobi Dock allows for storing and charging of three Interwrite Mobis™ or Interwrite Mobi Learners™ at the same time. This Quick Reference Guide addresses the following tasks:  Inserting the Interwrite Mobi into the Interwrite Mobi Dock  Removing the Interwrite Mobi from the Interwrite Mobi Dock  Checking Charging Status  Connecting the Charging Source  Mounting the Interwrite Mobi Dock to the Wall  Connecting Two Interwrite Mobi Docks to Charge Simultaneously  Locking the Interwrite Mobi Dock Inserting the Interwrite Mobi into the Interwrite Mobi Dock 1. Push the Release Pad into the locked position. 2. Make sure the Mobi you plan on charging is turned off before inserting it into the Mobi Dock. Locked Unlocked Release Pad
  2. 2. 2 3. Line up the slot located on the back of the Mobi to the latch on the Mobi Dock. 4. Push the Mobi into the Dock until you hear a snap. 5. Push the Release Pad back into the Unlocked Position. Locking the Interwrite Mobi Dock 1. Make sure the Release Pad is in the locked position. 2. Locate the hole for the lock on the right side of the Release Pad. 3. Insert the lock into the hole and secure the lock. Removing the Interwrite Mobi from the Interwrite Mobi Dock 1. Push down on Release Pad until it is flush with the Mobi Dock in the unlocked position. 2. Take hold of the Mobi and pull it out of the Docking Station. 3. Press Release Pad again into the Locked Position after all the Mobis are removed so it will be ready for storage and recharging.
  3. 3. 3 Checking Charging Status Use the following table to indicate what the lights mean. Light Status All Lights Flash On Mobi Dock has been plugged into an power outlet Both Lights are solid Mobi and Interactive Pen are charging Mobi Light is Off Pen Light is On Mobi is finished charging Note: the pen light will always remain lit. The light will be off if the pen is not in the Mobi or Mobi Learner. Lights flashing The Mobi or Mobi Learner was inserted into the Mobi Dock while still on. Turn off the Mobi and reinsert the Mobi. Connecting the Charging Source 1. Turn the unit over and locate one of the two Power Jack Outlets. Select the one that will best suit your needs after hanging the unit or placing it on the desk. 2. Insert the Adapter into the Power Jack and thread the cord through the Cord Reservoir so it stays flush with the back of the unit. Power Jack Cord Reservoir
  4. 4. 4 Mounting the Interwrite Mobi Dock to the Wall You have two options for mounting the Mobi Dock.  Using the keyhole mounting holes on the back of the Mobi Dock.  Using the mounting holes through the front of the Mobi Dock. This option allows for permanent attachment to the wall. Note: Use the appropriate mounting nuts, bolts, and screws for your wall options. Due to the multitude of mounting options, eInstruction does not supply mounting screws for the Mobi Dock. Keyhole Mounting Holes Keyhole Mounting Holes Keyhole Mounting Holes Permanent Mounting Holes Permanent Mounting Holes
  5. 5. 5 Using the Keyhole Mounting Holes to Mount the Mobi Dock 1. Locate a secure mounting area, such as a stud and measure for the three keyhole openings. 2. Install the appropriate screws for your wall, leaving 1/8th of an inch between the head of the screw and the wall. 3. Slide the unit over the screws and allow it to move into place, securing the unit to the wall. 4. Slide the unit up and out to remove it. Using the Permanent Mounting Holes to Mount the Mobi Dock 1. Locate a secure mounting area, such as a stud and measure for the two openings. 2. Place the unit in the appropriate location and mark the holes for mounting. 3. Remove the unit and drill two pilot holes where the markings are located. 4. Place the unit back in the marked location, and install the screws into the wall, securing the unit to the wall. Connecting Two Interwrite Mobi Docks to Charge Simultaneously You can use a double-headed charger to connect two Mobi Docks, allowing you to charge up to six Mobis or Mobi Learners at the same time with the same charger. 1. Take one end of the adapter and connect it as you would with a single connection within the Mobi Dock. 2. Repeat for the second unit. 3. Install the units next to each other, and near the same outlet. 4. Place the Mobis and Mobi Learners into the units to charge, as you would a single unit.
  6. 6. 6 Declaration of Conformity The “CE“ mark on these devices indicates compliance under the EMC 2004/108/EC Directive. Declaration of conformity according to ISO/IEC Guide 22 and EN 45014 Manufacturer’s Name: eInstruction Corp Manufacturer’s Address: 308 N Carroll Blvd Denton, TX 76201 U.S.A. declares, that these products Product Name: MOBI DOCK Product Options: All conform to the following product specifications: RoHS: “-R” labelled products conform to DIRECTIVE 2002/95/EC. These products are RoHS-compliant. European Union WEEE Directive Further information about the responsible end-of-life management of this and other eInstruction products is available on our Web site at www.einstruction.com. European Contact: Centre Education Europe 26/36 rue Alfred Nobel 93600 Aulnay Sous Bois France TEL: +33 1.58.31.10.60 FAX: +33 1.58.31.10.69 www.interwritelearning.fr 37-01298-01 Copyright© 2009 eInstruction Interwrite and Workspace are trademarks of eInstruction, Inc. All other products and company names are the trademarks or registered trademarks of their respective owners. The information contained in this document is subject to change without notice. eInstruction assumes no responsibility for technical, or editorial errors, or omissions that may appear in this document, or for the use of this material. Nor does eInstruction make any commitment to update the information contained in this document. This document contains proprietary information which is protected by copyright. All rights reserved. No part of this document can be photocopied or reproduced in any form without the prior, written consent of eInstruction www.eInstruction.com/support Support: 480.443.2214

×