Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.
Smooth Firestop Sleeve
System Installation
UNIQUE Smooth Firestop Sleeve
System is a multi cable transit for
new horizontal installations of cables
and wires through...
The system includes:
(1) 12” EMT sleeve powder
coated RED
(2) large washers
(2) sliding lock couplings
(2) plenum rated bu...
Smooth Firestop Sleeve comes in 4-
inches, 2-inches, and 1-inch diameter.
INSTALLATION PICTORIAL
You should use a drill with a level. This will
make your Sleeve System install nice and
straight!
A 6-inch bit extension for your hole bits works
very well. Be wary of what might be in the
walls.
You might use one of the washers to mark your
hole. Now drill your perfectly straight hole.
There is no need for any caulk between the
sleeve and the wall (behind the washers).
Adjust the hardware
to allow for equa...
On the other side of
the wall, install the
washer, sliding
compression
coupling and
bushing.
While holding the
sleeve firm...
Now you may use the
sleeve system as if it
were a roller in the
firewall, allowing you
to pull cables
‘unattended’.
This i...
Tear the
intumescent putty
supplied with the
system in half. You
will need to apply an
inch thickness to
each end.
If you ...
When the cables reach their destination, install
an inch thickness of the supplied UNIQUE
Intumescent Putty.
Alpha numerically ID
your installation and
be sure to fill out and
apply the labels.
Now take a picture of
your installed system.
Visit our websitefor more firestop products
and completeinstallation pictorials.
https://www.uniquefirestop.com/
Upcoming SlideShare
Loading in …5
×

Unique Smooth Sleeve Firestop System Installation Pictorial

1,514 views

Published on

UNIQUE Smooth Firestop Sleeve System is a multi cable transit for new horizontal installations of cables and wires through fire and smoke rated walls. Manufactured from ASTM Electrical Metallic Tubing (EMT) to UL1479 standards. Available in 1-2-4 inch diameter.

Note: These systems are limited to 2 hour rated horizontal installations. For higher ratings or vertical installations, see our Threaded Firestop Sleeve Systems.

Published in: Engineering
  • Be the first to comment

  • Be the first to like this

Unique Smooth Sleeve Firestop System Installation Pictorial

  1. 1. Smooth Firestop Sleeve System Installation
  2. 2. UNIQUE Smooth Firestop Sleeve System is a multi cable transit for new horizontal installations of cables and wires through fire and smoke rated walls.
  3. 3. The system includes: (1) 12” EMT sleeve powder coated RED (2) large washers (2) sliding lock couplings (2) plenum rated bushings A pair of documentation/warninglabels A package of UNIQUE Intumescent Putty
  4. 4. Smooth Firestop Sleeve comes in 4- inches, 2-inches, and 1-inch diameter.
  5. 5. INSTALLATION PICTORIAL
  6. 6. You should use a drill with a level. This will make your Sleeve System install nice and straight!
  7. 7. A 6-inch bit extension for your hole bits works very well. Be wary of what might be in the walls.
  8. 8. You might use one of the washers to mark your hole. Now drill your perfectly straight hole.
  9. 9. There is no need for any caulk between the sleeve and the wall (behind the washers). Adjust the hardware to allow for equal protrusion on both sides of the wall. Insert the first half of the System in the hole you made.
  10. 10. On the other side of the wall, install the washer, sliding compression coupling and bushing. While holding the sleeve firmly in the wall, tighten the set screw on the sliding compression coupling.
  11. 11. Now you may use the sleeve system as if it were a roller in the firewall, allowing you to pull cables ‘unattended’. This is a real time saver!
  12. 12. Tear the intumescent putty supplied with the system in half. You will need to apply an inch thickness to each end. If you do not have enough putty, you may purchase an extra Fill Kit. It is an 18 cubic inch stick of UNIQUE Intumescent Putty.
  13. 13. When the cables reach their destination, install an inch thickness of the supplied UNIQUE Intumescent Putty.
  14. 14. Alpha numerically ID your installation and be sure to fill out and apply the labels.
  15. 15. Now take a picture of your installed system.
  16. 16. Visit our websitefor more firestop products and completeinstallation pictorials. https://www.uniquefirestop.com/

×