The document describes a project to design and fabricate a micro air vehicle (MAV) under the guidance of Prof. Syed Basith Muzammil. A group of 4 students - Shazaan Sayeed, Suman Mandal, Sushil Kumar, and Md Idris - are working on the project at HKBK College of Engineering. The MAV will have the ability to hover and be equipped with a camera and sensors to detect leaked gas and explosives. It will use basic materials like a frame, motors, propellers, microcontroller, battery, and transmitter/receiver. The working principle involves the microcontroller receiving signals from the transmitter to control the electronic speed controllers and motor speeds to adjust the altitude
1. Project Seminar
on
Micro Air Vehicle
Under the guidance of
Prof. Syed Basith Muzammil ME, (PhD)
(Asst. Professor, Dept. of Mechanical
Engineering)
BY
Shazaan Sayeed ( 1HK11ME082 )
Suman Mandal ( 1HK11ME085 )
Sushil Kumar ( 1HK11ME087 )
Md Idris ( 1HK11ME054 )
HKBK College
of
Engineering
2. CONTENTS
Introduction-MAV
Our Project
Advantages and Disadvantages
Applications
Basic Materials Required
Block Diagram
Circuit Diagram
Working Principle
Design and fabrication of MAV
3. Introduction
A quad-copter, also called a quad rotor helicopter is a
multi-rotor helicopter that is lifted and propelled by four
rotors.
It is a type of small representation of Unmanned Air
Vehicle.
The quad-copter is one of the most complex flying
machines due to its versatility to perform many types of
tasks.
Classical quad-copters are usually equipped with a four
rotors.
Quad-copters are symmetrical vehicles with four equally
sized rotors at the end of four equal length rods.
Design and fabrication of MAV
4. Our Project
Ability to hover in a stationary position.
Embedded with a camera for capturing live images
or videos of its propagation(fitted with GPS
system).
Equipped with:
LPG sensor for detecting leaked out LPG gas to
prevent future explosion.
Explosive Detector Mo-8 – Tvin to detect the
explosives such as TNT, NG, PETN, C4 and their
mixtures.
Design and fabrication of MAV
5. Advantages
Small sized quad-copters have frames that enclose the
rotors, permitting flights through more challenging
environments, with lower risk of damaging the vehicle or
surroundings.
Small sized MAV's makes the vehicles safer for closer
interaction.
Our MAV does not require mechanical linkages that vary
the rotor blade pitch angle as they spin. This simplifies the
design and maintenance of each vehicle.
The use of four rotors allows each individual rotor to have a
smaller diameter than the equivalent helicopter rotor,
allowing them to possess less kinetic energy.
Design and fabrication of MAV
6. Disadvantages
Fabrication material not so trendy.
Can be controlled only up to a range of 100m.
Has a maximum flight time of about 25 minutes.
Skilled operator is needed.
Complex design and calculations.
Design and fabrication of MAV
7. Applications
Surveillance in military and
security sectors to disclose any
enemy troops in a war field.
Security and law enforcement
surveillance.
Research and rescue mission in
urban environments.
Detect leaked gas chambers or
pipelines in industries.
Inspection of power lines.
Detect explosives such as TNT,
C4, NG, PETN, etc. in public
sectors without any need of
human intervention.
Design and fabrication of MAV
8. Basic Materials Required
Frame
Transmitter and receiver
Electronic Speed Controller-4
Propellers-4 ( 2CW and 2 CCW )
Microcontroller- ATMega8
Camera
Sensors
Battery (11.1v 5000mAh Li-Po ) and Charger
Design and fabrication of MAV
9. Working Principle
Quad copter is a device with an intense mixture of
Electronics, Mechanical and mainly on the principle of
Aviation
The quad copter has 4 motors whose speed of rotation
and direction of rotation changes according to the user's
desire to move the device in a particular direction.
The rotation of Motors changes as per the transmitted
signal sent form the 6-Channel Transmitter.
The program for which is written in the AT-MEGA8 chip.
The signal from Microcontroller goes to the ESC's which in
turn controls the speed of motor and hence drives the
copter.
Design and fabrication of MAV
10. Block Diagram
Micro
Controller
AT Mega8
Arduino
Development
Board
Radio Frequency
Transmitter
Gyroscope
Sensor data
Battery
Camera data
ESC
Change in
direction and
altitude
Send signals to
receiver
Change the
motor speed
R/F Receiver Image receptor
Sensor detector
Design and fabrication of MAV
11. Electronic Circuit Block Diagram
Micro- Controller
ATMega8
Live video streaming
Driver- LED/ Buzzer
ESC- Motor speed
PWM to R/C Transmitter
DAC & ADC
convertor
Power Supply
4 bit data encoder
Oscillator
Data from Remote
Controller
Design and fabrication of MAV
12. Micro Controller- ATMega8 Features
The micro controller used in ATMega8 as it gives high performance even in
low voltages.
Nonvolatile Program and Data Memories ( 10,000 write cycles ).
Operating voltages= 0-5.5 volts
Power Consumption at 4 MHz, 3V at 35 °C
1K Byte Internal SRAM
The Micro controller receives power from batteries and data from the
remote controller.
The analog-digital and digital-analog conversion takes place.
The micro controller regulates the electronic speed controllers (ESC)
which in turn regulates the rotor speed and in turn controlling the
direction and movement of the vehicle.
It then creates wireless signals through oscillators and sends signals
to the receiver via transmitters .
Design and fabrication of MAV
13. Hardware Components
Basic Flight Dynamics
Pitching
Yawing
Rolling
Hover in X, Y, Z co ordinate
Lift
Descend
Design and fabrication of MAV
14. Controlling directions and height
Yawing: The movement of vehicle about Z axis. It causes change in
direction of the movement (right or left).
It happens when one set of opposite motors are driven at a relatively
higher speed than the other two.
Rolling: The movement of vehicle about Y axis. It causes to move the
vehicle side ways.
It happens when one of the side motor is driven at a relatively higher
speed than the opposite motor.
Pitching: Movement of vehicle
about X axis. It causes the
vehicle to move front or back.
It happens when the front
or rear motors move at
different speeds.
Design and fabrication of MAV
15. Hovering: For hovering, a balance of
forces is needed.
If we want the quad-copter to hover,
SUM(Fi) must be equal m•g.
To move the quad-copter
climb/decline the speed of every
motor is increased/decreased .
SUM(Fi) > m•g <=> climb
SUM(Fi) = m•g <=> hover
SUM(Fi) < m•g <=> decline
Design and fabrication of MAV
16. Component Parameters
Propellers: 4 * 10×4.7″ 2CW + 2CCW
Propeller Adapter: 4 * Propeller Shaft Adapters dia 3mm
Motor to motor dimension: 550mm
Maximum Flight time: 25 minutes
Motors: 4 * Emax CF2822 1200KV
ESC: 4 *30A Brushless Motor Speed Controller
Stability Control: 1 * MPU-6050 3 Axis Accelerometer + 3 Axis
Gyro
Design and fabrication of MAV
17. Calculations
Static Thrust : 𝑻 =
𝝅
𝟒
𝑫 𝟐
𝝆vΔv
T= Thrust (N)
D=propeller diameter (m)
v=velocity of air at propeller (m/s)
Δv=velocity of air accelerated by propeller (m/s)
Ρ=density of air ( approx. 1.225 kg/𝑚3 )
Velocity required for the quad copter to climb from ho to
any desired altitude of hf regardless of its angular
orientation
v2= 𝟒𝒈( 𝒉f – ho )
Hf = Desired altitude
H0 = Original altitude
Design and fabrication of MAV
18. Flight time = Battery capacity/amps
The drag equation from fluid dynamics gives us the
frictional force: 𝑭𝑫 =
𝟏
𝟐
𝝆𝑪 𝒅 𝑨 𝒗 𝟐
Ρ is the surrounding fluid density
A= propeller cross section
𝐶 𝑑 is dimensionless constant
Torque due to drag: T =
𝟏
𝟐
𝑹𝝆𝑪 𝒅 𝑨 𝒗 𝟐 =
𝟏
𝟐
𝑹𝝆𝑪 𝒅 𝑨 (𝝎𝑹) 𝟐
R= radius of the propeller
𝜔= angular velocity of the propeller
Design and fabrication of MAV