Youth Involvement in an Innovative Coconut Value Chain by Mwalimu Menza
D1005 gray correction
1. D1005
Gray Adjustment
Excerpted from
"What's New"
Please note that the addition here in this section is intended to help simplify the procedure
described in the document.
The "Correction Chart" function presented below makes a "ringaround" of small images
for judging the colour and density corrections tested. It's much easier to judge larger
images. NTS Canada suggests that instead of using the "Correction Chart" function, you
make full "Confirmation Chart" prints throughout the process.
Step 1. Select TYPE1 glossy or semi glossy and make sure there is no correction applied.
Typically, use 152mm paper for testing and the reference.
Step 2. Make a "Reference" TYPE1 print using the "Confirmation Chart" function as
below.
Step 3. Select TYPE3 on the same paper size and surface and make a print using the
"Confirmation Chart" function.
Step 4. Compare the two prints and determine the correction required to make the TYPE3
print match the TYPE1 print.
Step 5. Using the sliders, or the arrows apply the correction. Don't forget to click on the
"Register" button.
Step 6. Make another "Confirmation Chart" print and check to see if it matches. Repeat
as required to get it to match as close as possible.
If you are matching a second printer to the printer you just corrected, first match the
TYPE1 print of printer 2 to the TYPE1 print of Printer1. Use the same paper to compare
the two for consistency sake. After you match these, the correction found on printer 1 to
get TYPE3 prints to match TYPE1 prints should be the same. It will provide a good
starting point for sure.
**NOTE: You normally do not use TYPE2 or "Image Quality Priorty" channels. TYPE1
and TYPE2 should not look different. If you have a second printer, and find you need to
correct TYPE1 printing, then that correction should also be applied to TYPE2 printing if
you use that method of printing.
2. Ver. 3 to Ver. 3.10A
2.1.5 It is now available to adjust Gray Adjustment for each printing type(TYPE
1/TYPE 2/TYPE 3).
When adjusting the differences of print color (Color balance, Density, Tone) between printing type, they can be adjusted
Gray Adjustment for each printing type(TYPE 1/TYPE 2/TYPE 3)
TYPE 1
TYPE 1
TYPE 2
TYPE 3
Reference print
TYPE 2
TYPE 3
Make a reference print based on one printing type.
Adjust the print color of other printing type to this
reference print.
Print correction chart of other printers and adjust
them to this reference print.
G099964
NOTE
• TYPE 1 TYPE 2 TYPE 3
The types are separated according to the combination of Printing method (Standard (STD)/Image quality priority
(IQP)) on the Print Setting display and Print quality (Standard/Smooth) on the Paper Specification Registration
display.
Type
Printing method
Print quality
TYPE 1
Standard (STD)
Standard
TYPE 2
Image quality priority (IQP)
Standard
TYPE 3
Standard (STD) / Image quality priority
(IQP)
Smooth
For the D1005, Print quality can be configured only when the optional High Resolution Print Kit is installed.
Therefore, if the High Resolution Print Kit is not installed, TYPE 3 is not shown.
Bringing up the display
Printer Information display → Click Maintenance. → Extension → Maintenance → Various Adjustment → Gray
Adjustment
M5558-010V310
Adjusting method
1. Select the printing type as the standard.
Select the printing type of favorite print color from printing types.
If necessary, adjust Gray Adjustment(Color Balance Correction/Density Correction/Tone Correction) for each
printing type and then select the printing type of favorite print color.
The procedure of each adjustment is almost the same, however it has been changed partially. Refer to 2.1.6.
2
3. Ver. 3 to Ver. 3.10A
• For details of the adjustment procedure, refer to Operator's Manual 4.4 Adjusting the color balance, density
and tone of prints [Gray Adjustment]
M5558-010V310
NOTE
• When you select TYPE 1 and adjust TYPE 2 and TYPE 3 to TYPE 1 by inputting large amount of correction,
it may get tone reproduction damage.Therefore, recommend to select TYPE 2 on D1005(High Resolution Print
Kit is not installed) and select TYPE 3 on D1005(High Resolution Print Kit is installed ) and D1005HR.
2. Make a reference print ( Print confirmation chart ) of
the printing type as the standard.
Make each reference prints ( Print confirmation chart ) for Color Balance Correction,Density Correction and
Tone Correction.
M5558-010V310
3. Adjust the print color of other printing type to this reference print ( Print confirmation chart ).
Adjust each print color of Color Balance Correction,Density Correctionand Tone Correction.
(1) Print a correction chart of other printing type to be matched.
(2) Compare the printed correction chart with the printed confirmation chart, then select the closest color
of image.
Printed confirmation chart whose color balance is
used as standard.
The correction chart of the printer whose color
balance is to be adjusted
Select the closest color of image from the correction chart.
G099962
(3) Register the correction values to the printing type whose color tone is to be adjusted.
4. If
adjusting colors between printers, adjust them in the same procedure with using the
reference print.
3
4. Ver. 3 to Ver. 3.10A
2.1.6 Input range of correction for Color Balance Correction and Density Correction
of Gray Adjustment are increased to -15 to +15.
Bringing up the display
Printer Information display → Click Maintenance. → Extension → Maintenance → Various Adjustment → Gray
Adjustment
Display area of fine adjustment of Color Balance Correction display and Density Correction display
M5558-010V310
Selection display to print the correction chart for Color Balance Correction.
When printing the correction chart of Color Balance Correction, it can be printed by selecting the amount of change at 15
steps.
M5558-011V310
Selection display to print the correction chart for Density Correction.
When printing the correction chart of Density Correction, it can be printed by selecting one of three ranges which are
divided the amount of change from -15 to +15.
M5558-012V310
4
5. Ver. 3 to Ver. 3.10A
The correction chart is as follows.
S099963
2.1.7 When copying the correction data of Gray Adjustment, the information of
printing type has been added.
You can copy the correction values to other types of paper on the Gray Adjustment display, and now the information of
printing type has been added.(TYPE 1/TYPE 2/TYPE 3)
Bringing up the display
Printer Information display → Click Maintenance. → Extension → Maintenance → Various Adjustment → Gray
Adjustment → Click Correction data management.
Example: Correction data management display
Information of printing
type
M5558-01-03V310
5