The evolution of my talents and abilities with CAD programs and as a team player.

1. MICK LEWIS
 micklewis12345@hotmail.com
 425-789-6305
 Mechanical Drafting
 CAD
 Blueprint Reading
 Production Drawings
 Estimating

2. Table of Contents
 Capstone Project
 Party Barbecue
 Evolution of a project
 Wheel Assembly
 Catia v5 R21
 Solid Works
 AUTO-CAD
 Adobe Illustrator

3. Water for All

4. Mission Statement

8. My Original Sketch and Concept
Visual Using Solid Works

9. My Parts
Produced with Solid Works

10. Buckets
Buckets Produced with a single sketch and Revolved Boss with Applied Material
Holes produced with Extruded Cut, Linear and Circular Patterns

11. Bucket Lids and Screen Mesh
Lids Produced with a single sketch
Revolved Boss and Applied Material
Screen Mesh Produced with 2
Sketches Extruded Boss and
Extruded Cut

12. Filter Media #1
Produced with Extruded Boss, Extruded Cut, Applied Material
And Applied Surface Finish

13. Filter Media #2
Sand Produced with Extruded Boss, Applied Material and Applied Surface Finish
Diffuser Plate Produced with Extruded Boss, Linear and Circular Patterns
And Applied Material

14. Filter Bucket Piping
Produced with Extruded and Revolved Boss, Extruded Cut, Linear Pattern
And Applied Material

15. Shut-Off Valve
Fully Operational Sub-Assembly

16. My Drawings
Produced with Solid Works

17. Shut Off Valve

18. Diffuser Plate and Filter Bucket Lid

19. Buckets

20. Filter Bucket Piping

21. Filter Bucket Sub-Assembly – Exploded
with Bill of Materials

22. Team Member Parts
Produced with Solid Works

23. UV Tank by Aaron Tonn

24. Potable Water Tank and Final Assembly
by Ed Dick

25. Party Barbecue
Solid Works

28. TOP GRILL
CENTER
SECTION
BOLT

29. Evolution of a
Sheet Metal Project
Concept Sketch using Auto-Cad
First Design (Self Taught) using Solid Works
Final Practical Design using Catia v5 R21

30. Concept Sketch using Auto-Cad

31. First Design using Solid Works

36. Final Design using Catia v5 R21
RV STEPS
ASSEMBLY
Using Anchor,
Concentric,
Contact and Offset
Constraints

37. RV STAIRS
Produced with Wall
On Edge Tool, Hole
And Position Sketch
Tools and Linear
Patterns.

38. RV STAIR BASE

39. `
RV STAIR BRACES
- 1 LEFT
-2 RIGHT

40. RV STAIR SIDE
PANEL
Produced with
Wall Tool

41. Catia v5 R21

42. Reverse Engineered Gear Box
Produced with Anchor, Concentric,
Contact and Offset Constraints

43. RING GEAR
Produced with Pad Tool,
Hole Tool, and Circular
Patterns.
Drawing with Section View
And Detail View.

44. PULLEY SHAFT
Produced with Pad and
Circular Pattern Tools.
Drawing with Multiple
Section Views for Clarity.

45. DRONE
I Participated
In The Lay-up
of the
Composite
Materials
Used on This
Project

46. Reverse Engineered Hard Drive Parts
PLATE GUIDE
Produced with Pad, Pocket,
Offset, Draft Angle
and Hole Tools
Drawing with Section and
Detail Views.

47. SPINDLE SUB-ASSEMBLY
Produced Using Anchor,
Concentric and Contact
Constraints.
Exploded View Shows All
Parts in the Assembly

48. ASSEMBLY
DRAWING

49. Boolean Operations
Add and Remove Body Tools

50. Combine/Split
Produced Using Extrapolate, Join and Split Tools

51. Multi-Pad
Produced with a Single Sketch
And Multi-Pad Tool

52. Pattern Exercise
Assemblies
Using Anchors, Concentric,
Contact and Offset
Constraints
Produced Using Slot Tool, Hole Tool,
Position Sketch and Linear Patterns

53. SOLID WORKS
Wheel Assembly
Left Under Defined to Allow the
Wheel to Spin

54. Bowl Using
Revolve and Shell
Commands
and Applied Material
V-Belt Pulley
Using Revolve Command
Circular Pattern
And Hole Wizard

55. Casting Part
Featuring
Draft Angles
Drawings
Featuring GD&T
And Surface Finish

56. Assembly
Exploded view
Bracket
Produced with Extruded
Boss, Extruded Cut
And Fillet Commands

57. Axle
Produced Using
Extruded Boss,
Extruded Cut
Draft Angle and
Hole Wizard Tools
Drawing Featuring
GD&T and Surface
Finish

58. ROTARY BRACKET
GD&T

59. AUTO-CAD
Auxiliary Views
Dimensions and Tolerancing

60. Isometric Part Sketch Metric Dimensioning Section View
Tangent Arcs Concentric and Tangent Arcs Multiple Tangent Lines and Arcs

61. Orthographic Views
Creating Orthographic Views
From Isometric Sketches

62. ARCHITECTURAL Floor Plan

63. ARCHITECTURAL Proposed Remodel Floor Plan

64. ARCHITECTURAL Remodel Floor Plan Featuring Revision Cloud

65. CIVIL ENGINEERING Layout of a Residential Development

66. CIVIL ENGINEERING Lot Layout

67. CIVIL ENGINEERING Landscaping Layout

68. Creating Viewports Featuring GD&T

69. Applying Shapes, Colors and Textures
Using Adobe Illustrator
Original Photo
Outline w/ Pen Tool
Apply Colors
Apply Textures
Gray Scale
Adjust Contrast,
Transparency, etc.