Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.
http://designforeveryone.howest.be/
BOEKENHOUDER 1.6                                 € 80                   2 hours and 5 minuteshttp://boekenhouder2012.blogs...
ASSEMBLY MANUAL    http://designforeveryone.howest.be/
BOEKENHOUDER 1.6BILL OF MATERIAL- 1 MDF sheets (2440x500x12mm): € 15- 1 Plexiglas sheet (600x450x6mm): € 5- 2 Locking spri...
1   BOEKENHOUDER 1.6    DESCRIPTION                 Search for someone    who has a laser cutting machine. Buy the    plex...
2   BOEKENHOUDER 1.6    DESCRIPTION               Rub all of the MDF    surfaces with sandpaper until they are smooth    e...
3   BOEKENHOUDER 1.6    DESCRIPTION             Indicate the positioin    of the tape with a pencil. Cut the adhesive    m...
4   BOEKENHOUDER 1.6    DESCRIPTION                  Cut the adhesive    magnet tape to the correct length and paste it   ...
5   BOEKENHOUDER 1.6    DESCRIPTION               Cut the double-sided    tape to the correct length and paste it onto the...
6   BOEKENHOUDER 1.6    DESCRIPTION    wood.                                 Stick it onto the MDF            Technical pl...
7   BOEKENHOUDER 1.6    DESCRIPTION                Cut the aluminium    extrusion profile with a metal saw. The length of ...
8   BOEKENHOUDER 1.6    DESCRIPTION                 Take your hand drill    with a drill bit size 2.5mm. Drill two holes i...
9   BOEKENHOUDER 1.6    DESCRIPTION    length of minium 500mm.                               Cut the nylon wire at a      ...
10   BOEKENHOUDER 1.6     DESCRIPTION               Tie the nylon wire     through the hole of the aluminium extrusion    ...
11   BOEKENHOUDER 1.6     DESCRIPTION              Cut the anti-slip plastic     at a length of 50mm and width of 8mm.    ...
12   BOEKENHOUDER 1.6     DESCRIPTION              Cut 2 strips of double-     sided tape at a length of 10mm and width of...
13   BOEKENHOUDER 1.6     DESCRIPTION               Stick the two cutted     parts of acrylic foam tape on each side of th...
14   BOEKENHOUDER 1.6     DESCRIPTION           Buy a mouthpiece and     cut the edges from it. This provides more     com...
15   BOEKENHOUDER 1.6     DESCRIPTION                 Put the rubber     mouthpiece onto the laser cutted mouth piece.    ...
16   BOEKENHOUDER 1.6     DESCRIPTION                 Once the mouthpiece     has been assembled you can start with the   ...
17   BOEKENHOUDER 1.6     DESCRIPTION                  Take the other sided     part and slided it into the intermediate p...
18   BOEKENHOUDER 1.6     DESCRIPTION                 Take the slide MDF     part and slide it into the appropriiate holes...
19   BOEKENHOUDER 1.6     DESCRIPTION                Take the small MDF     parts and slide them into the appropriiate hol...
20   BOEKENHOUDER 1.6     DESCRIPTION                  Slide the cutted     aluminium extrusion tube into the cutted hole ...
21   BOEKENHOUDER 1.6     DESCRIPTION              Lay the Plexiglas book     reader sheets onto the magnetic strip.      ...
22   BOEKENHOUDER 1.6     DESCRIPTION                Open your book and     lay it onto the nylon wire. Next, set the book...
23   BOEKENHOUDER 1.6     DESCRIPTION                 Hang    up    the     mouthpiece between the intermediate part and  ...
24   BOEKENHOUDER 1.6
TECHNICAL ADDENDUM      http://designforeveryone.howest.be/
Intermediate partMaterial: MDF wood     File: Inter_mdf.pdf    #UNITS: 1        Boekenhouder 1.6     HOWEST            Dat...
Side partMaterial: MDF wood     File: Side_mdf.pdf    #UNITS: 2        Boekenhouder 1.6     HOWEST            Date: 04/06/...
Small partMaterial: MDF wood   File: Small_mdf.pdf    #UNITS: 2        Book Holder 1.6     HOWEST           Date: 04/06/2012
Slide partMaterial: MDF wood    File: Slide_mdf.pdf    #UNITS: 2        Book Holder 1.6     HOWEST           Date: 04/06/2...
Book readerMaterial: Plexiglas   File: Reader_plexiglas.pdf    #UNITS: 2          Book Holder 1.6    HOWEST               ...
TEAM CONTACTS   http://designforeveryone.howest.be/
VANOVERBEKE.MAARTEN@GMAIL.COM       TEL +32 4 75 47 81 50  JASMIENDECANCQ@GMAIL.COM       TEL +32 4 85 25 29 87  KYLIE.BIE...
Upcoming SlideShare
Loading in …5
×

Handleiding boekenhouder 1.6

855 views

Published on

  • Be the first to comment

  • Be the first to like this

Handleiding boekenhouder 1.6

  1. 1. http://designforeveryone.howest.be/
  2. 2. BOEKENHOUDER 1.6 € 80 2 hours and 5 minuteshttp://boekenhouder2012.blogspot.com/ Maarten Van Overbeke / Jasmien Decancq http://designforeveryone.howest.be/
  3. 3. ASSEMBLY MANUAL http://designforeveryone.howest.be/
  4. 4. BOEKENHOUDER 1.6BILL OF MATERIAL- 1 MDF sheets (2440x500x12mm): € 15- 1 Plexiglas sheet (600x450x6mm): € 5- 2 Locking spring clips: € 0.10- mouthpiece: € 4.50- ALU extrusion profile(100xØ10mm): 1.5 €- adhesive magnetic tape: 4,45 €- double-sided tape: 4,99 €- anti-slip plastic: 3 €- acrylic foam double sided tape: 2.99 €- nylon wire: 2.45 € Tools: metal saw, hand drill, drill bit Ø2.5mm, sandpaper 180 grit, cutter knife Standard parts: 2 Locking spring clips Tailored parts: MDF and Plexiglas sheet
  5. 5. 1 BOEKENHOUDER 1.6 DESCRIPTION Search for someone who has a laser cutting machine. Buy the plexiglas and mdf sheet. Dowload file_plexiglas and file_mdf, those are available on our blog. Put them on a USB-stick and deliver it to person with the laser cutter machine. A few days later you will receive your lasered parts. Technical plan: part files on our blog Duration time lasering: 1 hour Laser cutting machine Standard parts: no Tailored parts: mouth piece, 2 reading sheets, 2 sided parts, intermediate piece, 2 small parts and one slide part. Action cost: 30 €
  6. 6. 2 BOEKENHOUDER 1.6 DESCRIPTION Rub all of the MDF surfaces with sandpaper until they are smooth enough, so you will not harm yourself while you assemble the product. Technical plan: no Duration time: 15 minutes Sandpaper 180 grit Standard parts: no Tailored parts: 2 sided parts, 1 intermediate piece and 2 small parts Action cost: no
  7. 7. 3 BOEKENHOUDER 1.6 DESCRIPTION Indicate the positioin of the tape with a pencil. Cut the adhesive magnet tape into pieces and glue it onto the wood. Technical plan: no Duration time: 10 minutes Magnetic tape Standard parts: no Tailored parts: intermediate piece Action cost: no
  8. 8. 4 BOEKENHOUDER 1.6 DESCRIPTION Cut the adhesive magnet tape to the correct length and paste it onto the end of the Plexiglas strip. Technical plan: no Duration time: 10 minutes Magnetic tape Standard parts: no Tailored parts: 2 reading sheet Action cost: no
  9. 9. 5 BOEKENHOUDER 1.6 DESCRIPTION Cut the double-sided tape to the correct length and paste it onto the heat shrink thick wall. Technical plan: no Duration time: 2 minutes Dubble-sided tape Standard parts: no Tailored parts: no Action cost: no
  10. 10. 6 BOEKENHOUDER 1.6 DESCRIPTION wood. Stick it onto the MDF Technical plan: no Duration time: 5 minutes Double-sided tape Standard parts: no Tailored parts: 2 MDF small parts Action cost: no
  11. 11. 7 BOEKENHOUDER 1.6 DESCRIPTION Cut the aluminium extrusion profile with a metal saw. The length of this tubes is about 60mm. Technical plan: no Duration time: 5 minutes Metal saw Standard parts: ALU extrusion profile(100xØ10mm): Tailored parts: no Action cost: no
  12. 12. 8 BOEKENHOUDER 1.6 DESCRIPTION Take your hand drill with a drill bit size 2.5mm. Drill two holes into the tubes. At both sides at a distance of 10mm. Technical plan: no Duration time: 5 minutes Hand drill, drill bit 2.5mm Standard parts: ALU extrusion profile Tailored parts: no Action cost: no
  13. 13. 9 BOEKENHOUDER 1.6 DESCRIPTION length of minium 500mm. Cut the nylon wire at a Technical plan: no Duration time: 30 seconds Cutter knife Standard parts: nylon wire Tailored parts: no Action cost: no
  14. 14. 10 BOEKENHOUDER 1.6 DESCRIPTION Tie the nylon wire through the hole of the aluminium extrusion profile. Do the same with the other end of the wire. Technical plan: no Duration time: 1 minute No Standard parts: ALU extrusion profile Tailored parts: no Action cost: no
  15. 15. 11 BOEKENHOUDER 1.6 DESCRIPTION Cut the anti-slip plastic at a length of 50mm and width of 8mm. Technical plan: no Duration time: 1 minute Cutter knife, ruler Standard parts: anti-slip plastic Tailored parts: no Action cost: no
  16. 16. 12 BOEKENHOUDER 1.6 DESCRIPTION Cut 2 strips of double- sided tape at a length of 10mm and width of 6mm. Depending on which size of tape you use. Attention! We use an acrylic foam tape double-sided tape because of it’s sustainability. Technical plan: no Duration time: 1 minute Cutter knife, ruler Standard parts: acrylic foam double-sided tape Tailored parts: no Action cost: no
  17. 17. 13 BOEKENHOUDER 1.6 DESCRIPTION Stick the two cutted parts of acrylic foam tape on each side of the laser cutted mouthpiece, as shown on the picture. On top of that, you stick the anti-slip plastic. Attention! There has to be some space in between the anti-slip plastic and the laser cutted mouthpiece, this ensures more grip onto the paper. Technical plan: no Duration time: 5 minute No Standard parts: no Tailored parts: laser cutted mouthpart, parts of page 11 and 12 Action cost: no
  18. 18. 14 BOEKENHOUDER 1.6 DESCRIPTION Buy a mouthpiece and cut the edges from it. This provides more comfort for the user. Technical plan: no Duration time: 3 minute Cutting knife Standard parts: mouthpiece Tailored parts: no Action cost: no
  19. 19. 15 BOEKENHOUDER 1.6 DESCRIPTION Put the rubber mouthpiece onto the laser cutted mouth piece. Technical plan: no Duration time: 5 seconds Cutting knife Standard parts: Plexiglas mouth piece and rubbber mouthpiece Tailored parts: no Action cost: no
  20. 20. 16 BOEKENHOUDER 1.6 DESCRIPTION Once the mouthpiece has been assembled you can start with the bookreader. Take the intermediate MDF part and slide it into one sided MDF part. Technical plan: no Duration time: 10 seconds No Standard parts: No Tailored parts: one sided mdf part and the intermediate mdf part Action cost: no
  21. 21. 17 BOEKENHOUDER 1.6 DESCRIPTION Take the other sided part and slided it into the intermediate part. Technical plan: no Duration time: 10 seconds No Standard parts: No Tailored parts: one sided mdf part and the intermediate mdf part Action cost: no
  22. 22. 18 BOEKENHOUDER 1.6 DESCRIPTION Take the slide MDF part and slide it into the appropriiate holes, on the back of the bookreader. Technical plan: no Duration time: 10 seconds No Standard parts: No Tailored parts: slide MDF part Action cost: no
  23. 23. 19 BOEKENHOUDER 1.6 DESCRIPTION Take the small MDF parts and slide them into the appropriiate holes, in the intermediate MDF part. Technical plan: no Duration time: 10 seconds No Standard parts: No Tailored parts: 2 small MDF parts Action cost: no
  24. 24. 20 BOEKENHOUDER 1.6 DESCRIPTION Slide the cutted aluminium extrusion tube into the cutted hole and insert the locking spring clip. Do the same at the other side. Technical plan: no Duration time: 10 seconds No Standard parts: No Tailored parts: 2 small MDF parts, 2 locking spring clips and 2 alu extrusion tubes with nylon wire Action cost: no
  25. 25. 21 BOEKENHOUDER 1.6 DESCRIPTION Lay the Plexiglas book reader sheets onto the magnetic strip. Technical plan: no Duration time: 10 seconds No Standard parts: No Tailored parts: 2 Plexiglas bookreader sheets Action cost: no
  26. 26. 22 BOEKENHOUDER 1.6 DESCRIPTION Open your book and lay it onto the nylon wire. Next, set the book reader sliders onto the appropriate distance. Technical plan: no Duration time: 10 seconds Book Standard parts: No Tailored parts: No Action cost: no
  27. 27. 23 BOEKENHOUDER 1.6 DESCRIPTION Hang up the mouthpiece between the intermediate part and the book. This ensures that the reader doesn’t have to put the mouthpiece continuously into his mouth while reading. Technical plan: no Duration time: 10 seconds Book Standard parts: No Tailored parts: No Action cost: no
  28. 28. 24 BOEKENHOUDER 1.6
  29. 29. TECHNICAL ADDENDUM http://designforeveryone.howest.be/
  30. 30. Intermediate partMaterial: MDF wood File: Inter_mdf.pdf #UNITS: 1 Boekenhouder 1.6 HOWEST Date: 04/06/2012
  31. 31. Side partMaterial: MDF wood File: Side_mdf.pdf #UNITS: 2 Boekenhouder 1.6 HOWEST Date: 04/06/2012
  32. 32. Small partMaterial: MDF wood File: Small_mdf.pdf #UNITS: 2 Book Holder 1.6 HOWEST Date: 04/06/2012
  33. 33. Slide partMaterial: MDF wood File: Slide_mdf.pdf #UNITS: 2 Book Holder 1.6 HOWEST Date: 04/06/2012
  34. 34. Book readerMaterial: Plexiglas File: Reader_plexiglas.pdf #UNITS: 2 Book Holder 1.6 HOWEST Date: 04/06/2012
  35. 35. TEAM CONTACTS http://designforeveryone.howest.be/
  36. 36. VANOVERBEKE.MAARTEN@GMAIL.COM TEL +32 4 75 47 81 50 JASMIENDECANCQ@GMAIL.COM TEL +32 4 85 25 29 87 KYLIE.BIESBROUCK @HOWEST.BE TEL +32 4 76 41 30 95 http://designforeveryone.howest.be/

×