Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

PRETORIUS JG (DM)

312 views

Published on

  • Be the first to comment

  • Be the first to like this

PRETORIUS JG (DM)

  1. 1. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. 1 Off-job Phase Test 1 10-DM Select and change bearings for a combined radial and axial load 12-F Select and change bearings for a radial load 14-F Select and change bearings for a combined radial a 17-DM Maintain a propeller shaft 2 Off-job Phase Test 2 21-DM Maintain a diesel engine fitted with an in-line fuel system 24-DM Service V-belts 25-DM Service multiple V-belt drives 26-DM Service poly V drives (flat with grooves) 27-DM Demonstrate all ahnd signals applicable to rigging 28-DM Rig and lift vertically, equipment with a mass not 28-FM Operate a portable grinder 28-FT Operate a pedestal grinder 29-DM Recover a broken down vehicle fitted with manual t 3 Off-job Phase Test 3 30-DM Recover a broken down vehiclke fitted with automat 31-DM Maintain a servo assisted hydraulic brake system 31-FT Operate a portable drill 32-DM Maintain a pneumatic brake system 33-DM Read and interpret hydraulic circuit diagrams and explain the function and operation of each component 12014-09-11Print date: www.mqa.org.za
  2. 2. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. 34-DM Maintain the hydraulic circuits on the following Machines: a. Front end loader b. Forklift c. Rear dump truck d. road grader 35-DM Operate a power saw 36-DM Operate a pedestal grinder 37-DM Operate a portable grinder 38-DM Operate a pedestal drill 39-DM Operate a portable drill 4 Off-job Phase Test 4 40-DM Operate a valve grinder and refacer 43-DM Lubricate and service the following units on a veh 44-DM Maintain and adjust the clutch of a vehicle 45-DM Maintain the cooling system of a vehicle 46-DM Change, align and adjust the tracks of a track driven vehicle 48-DM Test a battery 48-P Rig and lift vertically, equipment with a mass not 49-DM Maintain a charging system 5 Off-job Phase Test 5 50-DM Maintain a starter motor 51-DM Repair a flat tyre 55-DM Maintain an orbital hydraulic steering 6 Off-job Phase Test 6 7 Off-job Phase Test 7 22014-09-11Print date: www.mqa.org.za
  3. 3. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. 8-DM Select and change bearings for a radial load 9-DM Select and change bearings for an axial load A On-job Phase Test A AAB Maintain air-assisted brakes ATF Allowances and tolerances for fits B On-job Phase Test B BBS Temper and grind a chisel BIF Examine bearings BRR-1 Mount a bearing manually BRR-2 Remove a bearing mechanically BRR-3 Remove and mount a bearing with adaptor sleeve BRR-4 Remove and mount a bearing in a press C On-job Phase Test C CCD Course control documents CLU-DM Strip, inspect and maintain clutches D On-job Phase Test D DDA Tune-up on a direct pump fuel system DPA Tune-up an engine fitted with a distributer or in- DRG Read engineering drawings DRG-1-P Read Engineering drawings E On-job Phase Test E FPC Fit split pins and circlips 32014-09-11Print date: www.mqa.org.za
  4. 4. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. FT Fit washers and tighten screws HB Overhaul hydraulic brakes HTT Use a file and saw HYD-1 Principles of hydraulics HYD-10 Construct a circuit with sequenced actuators HYD-11 Construct a circuit with an accumulator HYD-12 Make up hydraulic hoses HYD-13 Diagnose and test an hydraulic circuit HYD-2 Test the pump in a circuit HYD-3 Fit and set pressure relief valves HYD-4 Construct a circuit with a single-acting cylinder HYD-5 Construct a circuit with double-acting cylinders HYD-6 Construct a circuit with a check valve HYD-7 Construct a circuit with rotary motion HYD-8 Control the speed of an actuator HYD-9 Construct a dual circuit LM Lift and move equipment LUB-2 Pack a plumber block MCS-1 Maintain a storage battery MCS-2 Maintain auto-electrical systems MDF Drill a flange MDG Sharpen a drill 42014-09-11Print date: www.mqa.org.za
  5. 5. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. MDM Maintain a pedestal drill MMG Maintain a pedestal grinder MMI Use measuring instruments MPD Plan a drilling workpiece OA-1 Operate oxy-acetylene cutting equipment OAW Use welding equipment OB Overhaul and maintain the blower of an engine OCA Overhaul a cylinder head assembly ODF-1 Strip, clean and inspect a differential and final drive ODF-2 Assemble a differential and final drive OMT-1 Select the gear ratios on a manual transmission OMT-2 Overhaul a manual transmission OPT Overhaul a power transmission OSA Overhaul a sub-assembly OSS Repair a steering system OT Overhaul and maintain a turbocharger PDC Maintain cylinder heads PDF Maintain fuel systems PDO Maintain lubrication systems PDS Start a four-stroke petrol/diesel engine PDW Maintain cooling systems PN-1 Principles of pneumatics 52014-09-11Print date: www.mqa.org.za
  6. 6. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. PN-2 Construct a circuit with single acting cylinders PN-3 Fit and adjust a service unit PN-4 Control the speed of single acting cylinders PN-5 Construct a circuit controlled from two points PN-6 Control the speed of a double acting cylinder PN-7 Design and construct a pneumatic circuit PN-8 Set pressure sequence valves PN-9 Construct and set a circuit with a time delay valve PT Tune-up on a pressure timed (PT) fuel system SPG-1 Cut and fit gaskets SPG-2 Fit seals and packings TC Cut a thread with stock and dies TRS Drill and tap holes TS Identify threads UN Remove and replace universal joints VG Grind valves 62014-09-11Print date: www.mqa.org.za
  7. 7. This is to confirm that : Learner Name ID Number Employer Reference No Unit Standard Code Unit Standard Title JACQUES PRETORIUS 7408235100086 18 3 was enrolled in the Learning Programme : DIESEL MECHANIC Coal and was assessed and found competent in the following unit standards Mining Qualifications Authority 7 Anerley Road Parktown, Johannesburg, 2193 Private Bag X118, Marshalltown, 2107 Tel: 011 547 2600 Email: info@mqa.org.za Statement of Results COLLIERY TRAINING COLLEGEProvider The Learner passed the Trade Test on 2014-09-10 and a certificate will be issued by the MQA in due course. Chief Executive Officer Sam Seepei 72014-09-11Print date: www.mqa.org.za

×