www.collegehillshonda.com
                                                                Accessory                       ...
www.collegehillshonda.com
TOOLS AND SUPPLIES REQUIRED                    Illustration of the Fog Lights on the Vehicle
Phi...
www.collegehillshonda.com
4.     Remove the front bumper (four self-tapping screws,                                6.     ...
www.collegehillshonda.com
8.   Cut off the four ribs on the front bumper as shown.               10. Inside the bumper, in...
www.collegehillshonda.com
Routing the Fog Light Harness                                                              17. R...
www.collegehillshonda.com
     Without a Vehicle Harness: Secure the fog light                    Without a Vehicle Harnes...
www.collegehillshonda.com
23. Route the fog light harness as shown, and secure                                    25. Rein...
www.collegehillshonda.com
27. Remove the driver’s dashboard lower cover (seven                  29. Pull back the door ope...
www.collegehillshonda.com
31. Remove the steering column upper cover (two                                 33. Plug the rel...
www.collegehillshonda.com
36. Plug the switch harness 2-pin connector into the                  38. Get the fog light swit...
www.collegehillshonda.com
42. Turn the steering wheel 90° counterclockwise, and                                   44. Inst...
www.collegehillshonda.com
46. If the 20A fuse is already installed in the fuse box, go          Fog Light Aiming Adjustmen...
www.collegehillshonda.com
BULB REPLACEMENT                                                                   4.         In...
Upcoming SlideShare
Loading in …5
×

www.collegehillshonda.com

715 views

Published on

0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
715
On SlideShare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
5
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

www.collegehillshonda.com

  1. 1. www.collegehillshonda.com Accessory Application Publications No. INSTALLATION FOG LIGHTS 2010 CR-V AII 42602-42850 Issue Date INSTRUCTIONS OCT 2009 PARTS LIST Relay bracket Fog Light Kit (With Auto Lights) P/N 08V31-SWA-100A Fog Light Kit (Without Auto Lights) P/N 08V31-SWA-100B 11 Wire ties Right fog light 4 Wire ties with clip Left fog light 2 Harness tapes Fog light harness 6 Self-tapping screws, 5 x 14 mm Switch harness 6 x 16 mm Washer bolt Right trim 6 mm Flange nut Left trim 20A Fuse 2 Clips Light/turn signal switch Relay © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 08V31-SWA-1000-9A 1 of 13
  2. 2. www.collegehillshonda.com TOOLS AND SUPPLIES REQUIRED Illustration of the Fog Lights on the Vehicle Phillips screwdriver LIGHT/TURN Flat-tip screwdriver SIGNAL SWITCH Diagonal cutters Ratchet 20A FUSE 10 mm Socket 10 mm Wrench Plastic trim tool T/N SILTRIMTL10 Isopropyl alcohol Shop towel Utility knife Tape RIGHT SWITCH Electrical tape FOG LIGHT HARNESS FOG LIGHT LEFT File HARNESS FOG LIGHT 922507AG Blanket INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the audio and navigation system if equipped, and write down the XM radio station presets if equipped. 2. Disconnect the negative cable from the battery. 3. Remove the front grille cover (seven clips). 7 CLIPS FRONT GRILLE COVER 920501BX 2 of 13 AII 42602-42850 (0910) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
  3. 3. www.collegehillshonda.com 4. Remove the front bumper (four self-tapping screws, 6. To protect the front bumper, apply masking tape to six clips, and two bolts). Have an assistant help you the front bumper around the left fog light opening. when removing and installing the front bumper. Place the front bumper on a blanket after removal. FRONT BUMPER 4 SELF- TAPPING SCREWS MASKING TAPE 930901AG 7. Using a utility knife, cut along the inner line of the hole as shown. Take care not to damage the front bumper. FRONT 6 CLIPS BUMPER FRONT Cut out. BUMPER 2 BOLTS 922304BG 5. Remove five clips from the left front inner fender, and pull down the left front inner fender. LEFT FRONT INNER FENDER CROSS SECTION Cut. 3 SHORT CLIPS Cut. LONG CLIP SHORT CLIP FRONT INNER FRONT 941701AB HOLE LINE BUMPER BUMPER 930902AG © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 3 of 13
  4. 4. www.collegehillshonda.com 8. Cut off the four ribs on the front bumper as shown. 10. Inside the bumper, install one clip to the front Remove any burrs. Remove the masking tape. bumper. FRONT BUMPER 4 RIBS Cut off. CROSS SECTION FRONT BUMPER HOLDER CLIP FRONT FRONT BUMPER 930903AG BUMPER 922305BG 9. From the outside of the bumper, install the left trim. 11. Install the left fog light to the front bumper using three 5 x 14 mm self-tapping screws. INSIDE VIEW PIN FRONT FRONT BUMPER BUMPER LEFT TRIM PIN LEFT FOG LIGHT 3 SELF-TAPPING FRONT SCREWS, BUMPER BUMPER OPENING 5 x 14 mm 922501AG Cut in step 7. 12. Repeat steps 6 thru 11 to install the right fog light on Check the 922402BG the right side of the front bumper. L mark. LEFT TRIM 4 of 13 AII 42602-42850 (0910) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
  5. 5. www.collegehillshonda.com Routing the Fog Light Harness 17. Route the fog light harness under the left headlight, and secure the fog light harness clip to the vehicle 13. Route the fog light harness 1-pin connector in front panel. of the left front inner fender as shown. Plug the fog light harness 1-pin connector to the vehicle 1-pin 3 FOG LIGHT LEFT connector. HARNESS CLIPS HEADLIGHT VEHICLE VEHICLE FOG LIGHT HARNESS BRACKET HARNESS VEHICLE HARNESS Secure the FRONT harness with no excess slack. WIRE TIE WIRE TIE VEHICLE 1-PIN CONNECTOR VEHICLE PANEL FRONT RESONATOR FOG LIGHT HARNESS SRS HARNESS FOG LIGHT HARNESS 18. Secure the other two fog light harness clips to the Do not secure. 1-PIN CONNECTOR LEFT FRONT holes in the resonator. 941702AB INNER FENDER 19. Secure the fog light harness to the front bulkhead. 14. Secure the fog light harness to the vehicle harness With a Vehicle Harness: Cut the clips off of the two with two wire ties. Do not secure the fog light harness wire ties with clips. Secure the fog light harness to to the SRS harness. the vehicle harness near the harness clips using two 15. Remove the vehicle ground bolt, and secure the fog wire ties. light harness ground terminal to the vehicle ground terminal with the vehicle ground bolt just removed. 2 WIRE TIES FOG LIGHT VEHICLE WITH CLIP HARNESS HARNESS FOG LIGHT 2 VEHICLE HARNESS CLIPS VEHICLE HARNESS 2 WIRE TIES FRONT WITH CLIP Cut off. WIRE TIE VEHICLE GROUND BOLT VEHICLE GROUND TERMINAL FOG LIGHT HARNESS GROUND TERMINAL 941703AB 16. Secure the fog light harness to the vehicle harness FRONT VEHICLE HARNESS FOG LIGHT with two wire ties. HARNESS 931201AG © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 5 of 13
  6. 6. www.collegehillshonda.com Without a Vehicle Harness: Secure the fog light Without a Vehicle Harness: Secure the fog light harness harness to the bumper beam using two wire ties with to the bumper beam using two wire ties with clip and one clip and one wire tie. wire tie. FOG LIGHT VEHICLE WIRE HARNESS PANEL FOG LIGHT FRONT BUMPER TIE HARNESS BEAM BUMPER BEAM FRONT FOG LIGHT 2 WIRE TIES 2 WIRE TIES HARNESS WITH CLIP WITH CLIP BUMPER 6303011B BEAM WIRE TIE 20. Route the fog light harness under the bumper beam 21. Using isopropyl alcohol on a shop towel, clean the towards the right side of the vehicle. Secure the fog bumper beam surface where the harness tape will light harness. attach. With a Vehicle Harness: Cut the wire ties off of the two wire ties with clip. Secure the fog light harness to 2 WIRE TIES BUMPER the vehicle harness using three wire ties. BEAM BUMPER VEHICLE FOG LIGHT BEAM HARNESS HARNESS FRONT WIRE TIE FRONT 2 HARNESS FOG LIGHT TAPES HARNESS VEHICLE HARNESS 22. Continue routing the fog light harness along the bumper beam to the right side of the vehicle. Secure the fog light harness under the bumper beam using two adhesive tapes and two wire ties connected FOG LIGHT together. 2 WIRE TIES Cut off. 2 WIRE TIES HARNESS WITH CLIP 2 VEHICLE CLIPS WITH CLIP 6 of 13 AII 42602-42850 (0910) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
  7. 7. www.collegehillshonda.com 23. Route the fog light harness as shown, and secure 25. Reinstall the inner fender. With the help of an the clip on the fog harness to the vehicle panel. assistant, bring the front bumper close to the vehicle, and plug the fog light harness 2-pin connectors into VEHICLE PANEL FOG the right and left fog lights. Reinstall the front LIGHT bumper. HARNESS FOG LIGHT HARNESS FOG LIGHT 2-PIN HARNESS CONNECTOR 2-PIN CONNECTOR FOG LIGHT HARNESS CLIP FRONT FOG LIGHT HARNESS 6303042B 24. Secure four remaining fog light harness clips to the holes in the vehicle panel. RIGHT FOG LIGHT Install position. FRONT LEFT BUMPER FOG LIGHT VEHICLE 922502BG PANEL Routing the Switch Harness 26. Remove the driver’s dashboard under cover (turn the knob and release the pin and the clip. KNOB FRONT Turn. VEHICLE PANEL PIN DRIVER’S DASHBOARD FRONT UNDER COVER CLIP FOG LIGHT 4 FOG LIGHT 6303080B HARNESS HARNESS CLIPS 6303053B © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 7 of 13
  8. 8. www.collegehillshonda.com 27. Remove the driver’s dashboard lower cover (seven 29. Pull back the door opening seal from around the clips and two hooks). driver’s kick panel, and remove the driver’s kick panel (two clips). 7 CLIPS DOOR OPENING SEAL 2 CLIPS Pull back. DRIVER’S DRIVER’S DASHBOARD KICK PANEL LOWER COVER HOOK 6303071B 6303100B 28. Remove the left front side step trim (three clips). 30. Lower the tilt lever. Using a flat-tip screwdriver, release one of the retaining tabs from the steering 3 CLIPS column lower cover. STEERING COLUMN LOWER COVER RETAINING TAB LEFT FRONT SIDE STEP TRIM 6303090B TILT LEVER FLAT-TIP SCREWDRIVER 6905030Y 8 of 13 AII 42602-42850 (0910) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
  9. 9. www.collegehillshonda.com 31. Remove the steering column upper cover (two 33. Plug the relay into the switch harness relay block. retaining tabs on each side). 2 RETAINING RELAY TABS STEERING COLUMN UPPER COVER Push. RELAY BRACKET SWITCH HARNESS RELAY BLOCK 6828010B 6819020Y 34. Install the relay bracket to the switch harness relay block. 32. Remove the steering column lower cover (two self- 35. Install the switch harness relay block on the vehicle tapping screws and one screw). panel using the 6 x 16 mm washer-bolt and the 6 mm flange nut. STEERING COLUMN VEHICLE SWITCH HARNESS LOWER COVER PANEL RELAY BLOCK 6 mm FLANGE NUT SCREW SELF-TAPPING SCREW 6819030Y FUSE 6 x 16 mm BOX WASHER-BOLT 6303130B © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 9 of 13
  10. 10. www.collegehillshonda.com 36. Plug the switch harness 2-pin connector into the 38. Get the fog light switch harness, and insert the white vehicle harness 2-pin connector. Secure the switch and pink switch harness terminals into the harness to the vehicle harness using two wire ties. appropriate cavities of the white vehicle 34-pin connector. SWITCH HARNESS 2-PIN CONNECTOR HARNESS SIDE VIEW VEHICLE 34-PIN CONNECTOR (white.) WHITE WIRE WHITE WIRE TERMINAL TERMINAL VEHICLE VEHICLE 2-PIN PINK WIRE HARNESS CONNECTOR TERMINAL ELECTRICAL TAPE PINK WIRE TERMINAL FUSE BOX SWITCH WIRE TIE HARNESS VEHICLE SWITCH WIRE TIE HARNESS SWITCH 940903AG HARNESS HARNESS 931203AG 37. Push the retaining tab (from the vehicle green 42-pin 39. Secure the switch harness to the vehicle harness connector, the white 34-pin connector, and the blue with electrical tape. 21-pin connector), and raise the lock lever from each connector. Remove the connectors from the fuse 40. Reinstall the connector cover, and reconnect the box. Close the lock and vehicle white 43-pin vehicle connectors. connector, and remove the cover by sliding it away 41. Secure the switch harness to the vehicle harness from the lock. using two wire ties. SWITCH VIEWED FROM FRONT HARNESS 42-PIN CONNECTOR 34-PIN CONNECTOR WIRE 21-PIN CONNECTOR TIE Slide. Push. FUSE BOX COVER Push. RETAINING FUSE TAB BOX VEHICLE HARNESS Push. 931204AG LOCK LEVER VEHICLE 34-PIN CONNECTOR FUSE VEHICLE BOX CONNECTORS 6303150B 10 of 13 AII 42602-42850 (0910) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
  11. 11. www.collegehillshonda.com 42. Turn the steering wheel 90° counterclockwise, and 44. Install the new light/turn signal switch on the steering unplug the vehicle connector from the light/turn column with two self-tapping screws. While installing signal switch. do not hold the light switch by the lever. VEHICLE HOLDER STEERING VEHICLE CONNECTOR CONNECTOR COLUMN TAB HOLE CASE LIGHT/TURN SIGNAL SWITCH RETAINING TAB LIGHT/TURN SIGNAL SELF-TAPPING SWITCH SCREW STEERING NEW LIGHT/TURN WHEEL LEVER SIGNAL SWITCH 6303180B 7109020E 43. Remove the two self-tapping screws from the light/ 45. Plug the vehicle connector into the new light/turn turn signal switch. While pushing the retaining tab, signal switch. slide the light/turn signal switch, and remove it from the steering column. While removing, do not hold the VEHICLE HOLDER CONNECTOR light/turn signal switch by the lever. VEHICLE CONNECTOR STEERING TAB COLUMN HOLE NEW LIGHT/ TURN SIGNAL CASE SWITCH NEW LIGHT/TURN SIGNAL SWITCH RETAINING TAB 6303210B SELF-TAPPING LIGHT/TURN SCREW LEVER SIGNAL SWITCH 7109010E © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 11 of 13
  12. 12. www.collegehillshonda.com 46. If the 20A fuse is already installed in the fuse box, go Fog Light Aiming Adjustment to step 47, otherwise install the 20A fuse to the fuse 51. Adjust the fog light: box. • Pull down the inner fender and under cover. • Adjust the aiming according to local laws and FUSE regulations. BOX • To adjust, turn the aiming adjustment knob in or out until the correct aiming is obtained. 52. Reinstall the bumper clips and bolts. FUSE BOX PLUGGING POINT To lower. To raise. 20A FUSE VIEWED FROM FRONT 6303220B 47. Check that all wire harnesses are routed properly and all connectors are plugged in. 48. Reinstall all removed parts. Do not reinstall the AIMING bumper clip and bolts that fasten the bumper at this ADJUSTMENT FOG LIGHT KNOB time. Check that all clips and fasteners are installed securely. 922503AG 49. Reconnect the negative cable to the battery. USE AND CARE 50. Reset the clock, and reset the XM radio presets (if equipped). How to Operate the Fog Lights • Turn the lights switch to the “ ” position (headlights on low beam). • Turn the fog light switch on (indicator is on). HEADLIGHT SWITCH AUTO/ OFF Low High FOG LIGHT OFF - - - - SWITCH ON - - ON - NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. • If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable. 12 of 13 AII 42602-42850 (0910) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
  13. 13. www.collegehillshonda.com BULB REPLACEMENT 4. Install the new bulb and socket to the fog light. Use 1. Remove one bolt and one clip, and pull down the only a Guine Honda halogen light bulb of specified under cover and inner fender. wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003. FRONT BUMPER • Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. • Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. CLIP BOLT 922504AG Turn. 2. Unplug the connector from the fog light. NEW BULB CONNECTOR LEFT FOG LIGHT FOG LIGHT NEW BULB 922506AG 5. Reinstall the removed parts in the reverse order of removal. • Check that the wire harnesses are not pinched. • Be sure to tighten the clip and bolts securely. BULB 6. Check the operation of the fog light; adjust the aiming if necessary. CONNECTOR 922505AG 3. Remove the bulb. © 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 42602-42850 (0910) 13 of 13

×